SunSun COP-10000 User manual

Instruction manual
Floating Fountain COP-10000
55562
Illustration similar, may vary depending on model
Please read and follow the operating instructions and safety information prior to initial operation.
Technical changes reserved!
Illustrations, functional steps and technical data may deviate insignificantly due to continuous further
developments.

© by WilTec Wildanger Technik GmbH Item 55562 Page 2
http://www.WilTec.de
http://www.aoyue.eu 06 2021-1
http://www.teichtip.de
The information contained in this document may alter at any time without prior notice. No part of this
document may be copied or otherwise duplicated without prior written consent. All rights reserved.
WilTec Wildanger Technik GmbH cannot be held liable for any possible mistakes in this operating man-
ual, nor in the diagrams and illustrations shown.
Although WilTec Wildanger Technik GmbH has made every possible effort to ensure that this operating
manual is complete, accurate and up-to-date, errors cannot be ruled out entirely.
If you have found an error or wish to suggest an improvement, we look forward to hearing from you.
Send us an e-mail to:
[email protected]
or use our contact form:
https://www.wiltec.de/contacts/
The most recent version of this manual in several languages can be found in our online shop:
https://www.wiltec.de/docsearch
Our postal address is:
WilTec Wildanger Technik GmbH
Königsbenden 12
52249 Eschweiler Germany
Do you wish to collect your goods? Our address for collection is:
WilTec Wildanger Technik GmbH
Königsbenden 28
52249 Eschweiler Germany
In order to shorten the waiting time and to allow for an easy on-site processing, we kindly ask you to
contact us briefly beforehand or to place your order via the webshop.
E-mail: [e-mail]
Phone: [phone]
Fax: [phone]
To return your goods for exchange, repair or other purposes, please use the following address. Atten-
tion! To allow for a trouble-free complaint or return, it is important to contact our customer service team
before returning your goods.
Retourenabteilung
WilTec Wildanger Technik GmbH
Königsbenden 28
52249 Eschweiler Germany
E-mail: [email protected]o
Phone: [phone]
Fax: [phone])

© by WilTec Wildanger Technik GmbH Item 55562 Page 3
http://www.WilTec.de
http://www.aoyue.eu 06 2021-1
http://www.teichtip.de
Introduction
Thank you for choosing to purchase this quality product. To minimise the risk of injury, we ask you to
always take some basic safety precautions when using this product. Please read this operating manual
carefully and make sure that you understand it.
Keep these operation instructions in a safe place.
Range of application
This product is suitable for water temperatures between 4 ℃and 35 ℃. The fountain can be used in
ponds, landscape wells, becks, etc. where it makes for a positive water aeration.
Attention!
In and near standing water, garden ponds, and swimming ponds, the use of this device is only allowed
with a fault current protection switch with a triggering nominal current up to 30 mA (according to VDE
0100 Article 702 and 738).
The device is not suitable for use in swimming pools, paddling pools of any kind or waters in which
people or animals may stay during operation. Operation of the device with people being in the danger
area is not permitted. If you have doubts or questions concerning the operation, contact an electrician.
The device is not intended for use by persons (including children) with impaired or limited physical,
sensory and mental abilities or lack of experience and/or real knowledge, unless they are supervised by
a person responsible for their safety or follow the instructions made by this person on how to correctly
use the device. Children should be supervised to ensure that they do not play with the device.
Safety instructions
•Perform a visual inspection of the device before every use. Do not use the device if the safety
appliances are damaged or worn out. Never override safety regulations.
•Only use the device accordingly to the intended purpose stated in this manual.
•You are responsible for the safety of the working zone.
•If the cable or the plug is damaged due to external influences, the cable must not be repaired,
but has to be replaced with a new one. This work can only be carried out by an electrician.
•The voltage of 230 V AC indicated on the type plate of the device must match the existent mains
voltage.
•Never lift, carry, or fix the device by using the power cable.
•Make sure that the electrical plug connection is protected from flood and moisture.
•Pull out the plug before maintaining.
•The user is responsible for complying with local safety and mounting regulations. If necessary,
ask a qualified electrician.
•Pull out the plug before you get into contact with the water surface.
•The device must never run dry or be operated with its suction line fully closed. The manufac-
turer’s warranty is void for damage to the device caused by dry running.
•Only use the product to pump water.
Note! If the water pump is overcharged (e.g., by a stuck rotor), the anti-bloc function installed inside the
device automatically switches it off. After repairing the fault, the product is re-switched on and re-oper-
ated.

© by WilTec Wildanger Technik GmbH Item 55562 Page 4
http://www.WilTec.de
http://www.aoyue.eu 06 2021-1
http://www.teichtip.de
Assembly
1. Insert one end of the holding rope included into the hole at the edge of the buoy (from two or
three different diagonal directions).
2. Attach the other end of the rope to the holding peg.
3. To fix the product, firmly put the holding peg into the muddy edge zone of the water body.
Note! When fixing, make sure that the motor is fully immerged in the water; otherwise, it might be dam-
aged.
Cleaning and maintenance
Regularly clean the pump for to allow it to keep its efficiency.
1. Hold the main part of the water pump with one hand, turning the buoy counter-clockwise with
the other hand to detach the main part of the water pump from the buoy (Fig. 1).
2. Turn the mounting frame counter-clockwise and remove it (Fig. 2).
3. Slide the latch downwards (Fig. 3).
4. Turn the upper cover lid to detach it from the lower cover lid of the main part (Fig. 4 and 5).
5. Unscrew the adjusting screw to remove the rotor unit (Fig. 6 and 7).
6. To clean the individual parts, use a soft brush and clean them under running water.
7. Re-mount the individual parts of the product after cleaning.

© by WilTec Wildanger Technik GmbH Item 55562 Page 5
http://www.WilTec.de
http://www.aoyue.eu 06 2021-1
http://www.teichtip.de
Storage during winter
1. Take the pump out of the water.
2. Thoroughly clean it.
3. Check the pump and power cord for damage.
4. The device must be stored in a frost-free place and in a container with as much water as possi-
ble.
Troubleshooting
Problem
Possible cause
Proposed solution
Pump does not start.
No mains voltage
Check energy supply.
Pump does not pump (sufficient)
water.
1. Obstruction of pump housing
1. Clean pump housing.
2. Rotor stuck
2. Thoroughly clean pump.
3. Air in the pump
3. Re-start pump.

© by WilTec Wildanger Technik GmbH Item 55562 Page 6
http://www.WilTec.de
http://www.aoyue.eu 06 2021-1
http://www.teichtip.de
Exploded view and parts list
№
Designation
№
Designation
1
Mounting frame
6
Rotor
2
Buoy
7
Ceramic support
3
Water filter cover
8
Support
4
Rotor
9
Motor body
5
Screw
Technical specifications
Model
COP-10000
Intake voltage (V)
220–240
Intake frequency (㎐)
50
Power consumption (W)
90
Height of water column (m)
1
Spraying radius (m)
3
Max. flow rate (ℓ⁄h)
20,000
Size (㎜)
275×252×420
Length of cable (m)
10

© by WilTec Wildanger Technik GmbH Item 55562 Page 7
http://www.WilTec.de
http://www.aoyue.eu 06 2021-1
http://www.teichtip.de
Regulations for waste disposal
The Waste Electrical and Electronic Equipment Directive (WEEE Directive, 2012/19/EU) of the EU was
implemented in the German law related to electrical and electronic equipment and appliances.
All WilTec electric devices that fall under the WEEE directive are labelled with the symbol of a crossed-
out wheeled rubbish bin. This symbol indicates that this electric device must not be disposed of with the
domestic waste.
WilTec Technik GmbH is registered with the German registration authority EAR (Stiftung Elektro-
Altgeräte Register) under the WEEE-registration number DE45283704.
Disposal of used electrical and electronic devices (in-
tended for use in the countries of the European Union
and other European countries with a separate waste
collection system for these devices).
The symbol on the packaging or the product itself indi-
cates that this product must not be treated as normal
domestic waste but must be disposed of at a recycling
collection station for electrical and electronic waste.
By disposing of this product correctly, you contribute to
the protection of the environment and the health of your
fellow people. Inappropriate disposal threatens the en-
vironment and health.
Material recycling helps to reduce the consumption of raw materials.
Additional information about the recycling of this product can be provided by your local commune, the
municipal waste disposal facilities, or the store where you purchased the product.
Address:
WilTec Wildanger Technik GmbH
Königsbenden 12 / 28
52249 Eschweiler Germany
Important Note:
Reproduction and any commercial use (of parts) of this operating manual, requires a written permission
of WilTec Wildanger Technik GmbH.