Sunwayi 4M58 User manual
User Manual
4M58
Important note:
The dash cam is not intended for use as a surveillance, security or
time-lapse camera system.
1. 4M58 DASH CAM(DVR) PROFILE
2. BUTTON DEFINITION
3. INSTALLATION & MOUNTING
4. FUNCTION
5. SETTING MENU
6. HOME SCREEN
7. FAQ
8. WARRANTY
1
2
3
4
5
6
7
7
- 1 -
1. 4M58 DASH CAM(DVR) PROFILE
TECHNICAL PARAMETERS
Video Resolution 1080FHD, 1080P, 720P, WVGA, VGA
Storage compression H.264
Video Format MOV
Picture Format JPG
Lens HD CMOS image sensor
DDR3 1GB
LCD Size 4.0 inches
LCD Resolution 800*480
G-SENSOR 380B
Working Power 4W
SD Card (TF) 4GB, 8GB, 16GB, 32GB, …,128GB(max)
Voltage DC 5V(1.5A)
Work Temperature -4°F~149°F(-20 ~65 )℃ ℃
Storage Temperature -13°F~167°F(-25 ~75 )℃ ℃
Air Pressure 960Mbar~1040Mbar
Battery 200mAh/3.7V lithium polymer battery
PARTS INCLUDED
Suction-cup mount
*1
DVR unit
*1
Trochilus
car charging adapter(12-24V)
*1
*1
Rear view camera
FEATURES
Private Tooling with Exclusive & Attractive Appearance.
Full HD 1080P for high Definition Video Recording.
Big Camera Lens(Diameter 1'' ) for HD Video and Photo.
170 Ultra-wide-Angle Camera provides multi-lane coverage.
High Quality Image Sensor & fill-in light for outstanding night video clarity.
Big IPS Screen 4'' for clear HD displaying and Clarify.
Dual Recording from Front & Back, Rearview camera assist parking reversing.
WDR function for HD video Clarity.
Gravity sensing, Motion detection, Parking monitor, License plate watermark.
12-24V /5V (1.5A) Car adapter with charging cable.
Works with Micro TF card 32GB(max128GB).
Suction cup mount swivels for optimal position.
Hands-free auto ON/OFF(turns ON/OFF with the vehicle).
Seamless loop Recording, Photo Taking, Replaying fuctions.
Video File Format: MOV.
- 2 -
1
Switch between Recording / Camera / Playback; When date/time
setting, press 0.5s to move the light bar to next choice; In recording
press 0.5s to lock video file.
MODE
FI
4M58 OVERVIEW
2. BUTTON DEFINITION
H
G
KTrochilus
J
LM
RESET
MIC
MODE
MENU O K
1 2 3 4 5 6A B
USB AV-IN
7 C D E
N
Definition & Operating Instructions
NO. Button/Point
LVoice broadcast
Speaker
In menu options, upward function; In standby or recording state,
picture in picture switch function.
UP
3
TF memory card slot, please install in correct direction.
FTF card slot
MENU
In standby mode, press 0.5s enter/exit setup menu; short press
(0.5s) twice to next menu-setup page;long press(3 seconds)
turn on/off fill-in light.
5
6lock the video file, to avoid being covered by loop recording.
LOCK
A RESET Resetting Key, System restart. Reset button is only used to
restore factory settings, when crashed or abnormal situation.
Microphone
MICB
plug the rearview camera.
AV IN HOLEE
The indictor light will on when energized or working.
Power/workG
H4.0'’ HD IPS Screen.
Screen
heat dissipation
I
MBracket
If there is reversing in any state, reverse image will show on the
screen.
Rear view
camera
N
Press 3s can ON/OFF the machine; press 0.5s can sleep/wake
the screen.
ON/OFF KEY
Screen Saving
7
Holder Port
D
You can choose to turn on in dark circumstance.
Fill-in light
J
In menu options, downward function; In standby or recording
state, record audio on/off.
DOWN
2
OK
Recording / camera / playback / confirmation key; In recording
mode, press 0.5s to start recording, press again to stop recording.
In camera mode, press 0.5s to taking photo; In menu mode, it’s
Enter(confirm)Key.
4
CFor providing power supply. connecting a PC to transfer data;
or power connector.
USB port
Camera LensK
4.Connect the dark red wire of camera
with reversing light. Inserting car charger machine will
automatically start recording, if there is reversing in any
state, reverse image will show on the screen. After
reversing, it will return to recording mode automatically.
3. Install and fix DVR on the front windshield;
5. Insert the adapter with charging cable in the car
cigarette lighter hole;
6. Insert the usb end of the charging cable in the DVR
usb port. Then route and hide the cable;
7. Swivel camera lens for optimal position;
8. Start car engine, format TF card, then check if DVR
installation is correct.
If correct, dash cam (DVR) indicator light will work,
and will enter recording automatically, recording
indicator light will start.
MOUNTING
INSTALLING 4M58 DASH CAM
1. Insert the hook of suction mount into the top slot of
the 4M58 as shown (A).
2. Select an area of the windshield directly above the
dash board(make sure not obstructing driving view),
then clean the area thoroughly.
3. With the suction lever in the released
position (B) press the suction cup
against the windshield (C) .Press
the suction lever toward the suction
cup to lock the mount in position (D).
4. To adjust the angle of the 4M58,
loosen the collar on the ball joint,
adjust the angle, then retighten in
the desired position (E).
3. INSTALLATION & MOUNTING
INSTALLATION
USB
power
socket
Rear view camera
1. Power off car engine;
2. Insert the right TF card in the card slot;
A
B
C
D
E
DVR
CAMERA ADJUSTMENT
The DVR camera records in one
direction. To record the view in front
of the vehicle. the camera should
face to the front windshield.
Optional:
To record the view inside of the vehicle, the camera should face the
rear window.
Sometimes should adjust camera lens direction to avoid direct sun glare.
MOUNTING REAR VIEW CAMERA
First, you need to make a hole in the rear of the car, pass the wire of the rear
view camera through this hole, and then connect the red wire on the rear view
camera to the reversing light cable on the car, and connect the black wire to the
DVR. Finally, use the provided screws to fix the rearview camera in place and
- 3 -
User Manual
4M58
Important note:
The dash cam is not intended for use as a surveillance, security or
time-lapse camera system.
1. 4M58 DASH CAM(DVR) PROFILE
2. BUTTON DEFINITION
3. INSTALLATION & MOUNTING
4. FUNCTION
5. SETTING MENU
6. HOME SCREEN
7. FAQ
8. WARRANTY
1
2
3
4
5
6
7
7
- 1 -
1. 4M58 DASH CAM(DVR) PROFILE
TECHNICAL PARAMETERS
Video Resolution 1080FHD, 1080P, 720P, WVGA, VGA
Storage compression H.264
Video Format MOV
Picture Format JPG
Lens HD CMOS image sensor
DDR3 1GB
LCD Size 4.0 inches
LCD Resolution 800*480
G-SENSOR 380B
Working Power 4W
SD Card (TF) 4GB, 8GB, 16GB, 32GB, …,128GB(max)
Voltage DC 5V(1.5A)
Work Temperature -4°F~149°F(-20 ~65 )℃ ℃
Storage Temperature -13°F~167°F(-25 ~75 )℃ ℃
Air Pressure 960Mbar~1040Mbar
Battery 200mAh/3.7V lithium polymer battery
PARTS INCLUDED
Suction-cup mount
*1
DVR unit
*1
Trochilus
car charging adapter(12-24V)
*1
*1
Rear view camera
FEATURES
Private Tooling with Exclusive & Attractive Appearance.
Full HD 1080P for high Definition Video Recording.
Big Camera Lens(Diameter 1'' ) for HD Video and Photo.
170 Ultra-wide-Angle Camera provides multi-lane coverage.
High Quality Image Sensor & fill-in light for outstanding night video clarity.
Big IPS Screen 4'' for clear HD displaying and Clarify.
Dual Recording from Front & Back, Rearview camera assist parking reversing.
WDR function for HD video Clarity.
Gravity sensing, Motion detection, Parking monitor, License plate watermark.
12-24V /5V (1.5A) Car adapter with charging cable.
Works with Micro TF card 32GB(max128GB).
Suction cup mount swivels for optimal position.
Hands-free auto ON/OFF(turns ON/OFF with the vehicle).
Seamless loop Recording, Photo Taking, Replaying fuctions.
Video File Format: MOV.
- 2 -
1
Switch between Recording / Camera / Playback; When date/time
setting, press 0.5s to move the light bar to next choice; In recording
press 0.5s to lock video file.
MODE
FI
4M58 OVERVIEW
2. BUTTON DEFINITION
H
G
KTrochilus
J
LM
RESET
MIC
MODE
MENU O K
1 2 3 4 5 6A B
USB AV-IN
7 C D E
N
Definition & Operating Instructions
NO. Button/Point
LVoice broadcast
Speaker
In menu options, upward function; In standby or recording state,
picture in picture switch function.
UP
3
TF memory card slot, please install in correct direction.
FTF card slot
MENU
In standby mode, press 0.5s enter/exit setup menu; short press
(0.5s) twice to next menu-setup page;long press(3 seconds)
turn on/off fill-in light.
5
6lock the video file, to avoid being covered by loop recording.
LOCK
A RESET Resetting Key, System restart. Reset button is only used to
restore factory settings, when crashed or abnormal situation.
Microphone
MICB
plug the rearview camera.
AV IN HOLEE
The indictor light will on when energized or working.
Power/workG
H4.0'’ HD IPS Screen.
Screen
heat dissipation
I
MBracket
If there is reversing in any state, reverse image will show on the
screen.
Rear view
camera
N
Press 3s can ON/OFF the machine; press 0.5s can sleep/wake
the screen.
ON/OFF KEY
Screen Saving
7
Holder Port
D
You can choose to turn on in dark circumstance.
Fill-in light
J
In menu options, downward function; In standby or recording
state, record audio on/off.
DOWN
2
OK
Recording / camera / playback / confirmation key; In recording
mode, press 0.5s to start recording, press again to stop recording.
In camera mode, press 0.5s to taking photo; In menu mode, it’s
Enter(confirm)Key.
4
CFor providing power supply. connecting a PC to transfer data;
or power connector.
USB port
Camera LensK
4.Connect the dark red wire of camera
with reversing light. Inserting car charger machine will
automatically start recording, if there is reversing in any
state, reverse image will show on the screen. After
reversing, it will return to recording mode automatically.
3. Install and fix DVR on the front windshield;
5. Insert the adapter with charging cable in the car
cigarette lighter hole;
6. Insert the usb end of the charging cable in the DVR
usb port. Then route and hide the cable;
7. Swivel camera lens for optimal position;
8. Start car engine, format TF card, then check if DVR
installation is correct.
If correct, dash cam (DVR) indicator light will work,
and will enter recording automatically, recording
indicator light will start.
MOUNTING
INSTALLING 4M58 DASH CAM
1. Insert the hook of suction mount into the top slot of
the 4M58 as shown (A).
2. Select an area of the windshield directly above the
dash board(make sure not obstructing driving view),
then clean the area thoroughly.
3. With the suction lever in the released
position (B) press the suction cup
against the windshield (C) .Press
the suction lever toward the suction
cup to lock the mount in position (D).
4. To adjust the angle of the 4M58,
loosen the collar on the ball joint,
adjust the angle, then retighten in
the desired position (E).
3. INSTALLATION & MOUNTING
INSTALLATION
USB
power
socket
Rear view camera
1. Power off car engine;
2. Insert the right TF card in the card slot;
A
B
C
D
E
DVR
CAMERA ADJUSTMENT
The DVR camera records in one
direction. To record the view in front
of the vehicle. the camera should
face to the front windshield.
Optional:
To record the view inside of the vehicle, the camera should face the
rear window.
Sometimes should adjust camera lens direction to avoid direct sun glare.
MOUNTING REAR VIEW CAMERA
First, you need to make a hole in the rear of the car, pass the wire of the rear
view camera through this hole, and then connect the red wire on the rear view
camera to the reversing light cable on the car, and connect the black wire to the
DVR. Finally, use the provided screws to fix the rearview camera in place and
- 3 -
User Manual
4M58
Important note:
The dash cam is not intended for use as a surveillance, security or
time-lapse camera system.
1. 4M58 DASH CAM(DVR) PROFILE
2. BUTTON DEFINITION
3. INSTALLATION & MOUNTING
4. FUNCTION
5. SETTING MENU
6. HOME SCREEN
7. FAQ
8. WARRANTY
1
2
3
4
5
6
7
7
- 1 -
1. 4M58 DASH CAM(DVR) PROFILE
TECHNICAL PARAMETERS
Video Resolution 1080FHD, 1080P, 720P, WVGA, VGA
Storage compression H.264
Video Format MOV
Picture Format JPG
Lens HD CMOS image sensor
DDR3 1GB
LCD Size 4.0 inches
LCD Resolution 800*480
G-SENSOR 380B
Working Power 4W
SD Card (TF) 4GB, 8GB, 16GB, 32GB, …,128GB(max)
Voltage DC 5V(1.5A)
Work Temperature -4°F~149°F(-20 ~65 )℃ ℃
Storage Temperature -13°F~167°F(-25 ~75 )℃ ℃
Air Pressure 960Mbar~1040Mbar
Battery 200mAh/3.7V lithium polymer battery
PARTS INCLUDED
Suction-cup mount
*1
DVR unit
*1
Trochilus
car charging adapter(12-24V)
*1
*1
Rear view camera
FEATURES
Private Tooling with Exclusive & Attractive Appearance.
Full HD 1080P for high Definition Video Recording.
Big Camera Lens(Diameter 1'' ) for HD Video and Photo.
170 Ultra-wide-Angle Camera provides multi-lane coverage.
High Quality Image Sensor & fill-in light for outstanding night video clarity.
Big IPS Screen 4'' for clear HD displaying and Clarify.
Dual Recording from Front & Back, Rearview camera assist parking reversing.
WDR function for HD video Clarity.
Gravity sensing, Motion detection, Parking monitor, License plate watermark.
12-24V /5V (1.5A) Car adapter with charging cable.
Works with Micro TF card 32GB(max128GB).
Suction cup mount swivels for optimal position.
Hands-free auto ON/OFF(turns ON/OFF with the vehicle).
Seamless loop Recording, Photo Taking, Replaying fuctions.
Video File Format: MOV.
- 2 -
1
Switch between Recording / Camera / Playback; When date/time
setting, press 0.5s to move the light bar to next choice; In recording
press 0.5s to lock video file.
MODE
FI
4M58 OVERVIEW
2. BUTTON DEFINITION
H
G
KTrochilus
J
LM
RESET
MIC
MODE
MENU O K
1 2 3 4 5 6A B
USB AV-IN
7 C D E
N
Definition & Operating Instructions
NO. Button/Point
LVoice broadcast
Speaker
In menu options, upward function; In standby or recording state,
picture in picture switch function.
UP
3
TF memory card slot, please install in correct direction.
FTF card slot
MENU
In standby mode, press 0.5s enter/exit setup menu; short press
(0.5s) twice to next menu-setup page;long press(3 seconds)
turn on/off fill-in light.
5
6lock the video file, to avoid being covered by loop recording.
LOCK
A RESET Resetting Key, System restart. Reset button is only used to
restore factory settings, when crashed or abnormal situation.
Microphone
MICB
plug the rearview camera.
AV IN HOLEE
The indictor light will on when energized or working.
Power/workG
H4.0'’ HD IPS Screen.
Screen
heat dissipation
I
MBracket
If there is reversing in any state, reverse image will show on the
screen.
Rear view
camera
N
Press 3s can ON/OFF the machine; press 0.5s can sleep/wake
the screen.
ON/OFF KEY
Screen Saving
7
Holder Port
D
You can choose to turn on in dark circumstance.
Fill-in light
J
In menu options, downward function; In standby or recording
state, record audio on/off.
DOWN
2
OK
Recording / camera / playback / confirmation key; In recording
mode, press 0.5s to start recording, press again to stop recording.
In camera mode, press 0.5s to taking photo; In menu mode, it’s
Enter(confirm)Key.
4
CFor providing power supply. connecting a PC to transfer data;
or power connector.
USB port
Camera LensK
4.Connect the dark red wire of camera
with reversing light. Inserting car charger machine will
automatically start recording, if there is reversing in any
state, reverse image will show on the screen. After
reversing, it will return to recording mode automatically.
3. Install and fix DVR on the front windshield;
5. Insert the adapter with charging cable in the car
cigarette lighter hole;
6. Insert the usb end of the charging cable in the DVR
usb port. Then route and hide the cable;
7. Swivel camera lens for optimal position;
8. Start car engine, format TF card, then check if DVR
installation is correct.
If correct, dash cam (DVR) indicator light will work,
and will enter recording automatically, recording
indicator light will start.
MOUNTING
INSTALLING 4M58 DASH CAM
1. Insert the hook of suction mount into the top slot of
the 4M58 as shown (A).
2. Select an area of the windshield directly above the
dash board(make sure not obstructing driving view),
then clean the area thoroughly.
3. With the suction lever in the released
position (B) press the suction cup
against the windshield (C) .Press
the suction lever toward the suction
cup to lock the mount in position (D).
4. To adjust the angle of the 4M58,
loosen the collar on the ball joint,
adjust the angle, then retighten in
the desired position (E).
3. INSTALLATION & MOUNTING
INSTALLATION
USB
power
socket
Rear view camera
1. Power off car engine;
2. Insert the right TF card in the card slot;
A
B
C
D
E
DVR
CAMERA ADJUSTMENT
The DVR camera records in one
direction. To record the view in front
of the vehicle. the camera should
face to the front windshield.
Optional:
To record the view inside of the vehicle, the camera should face the
rear window.
Sometimes should adjust camera lens direction to avoid direct sun glare.
MOUNTING REAR VIEW CAMERA
First, you need to make a hole in the rear of the car, pass the wire of the rear
view camera through this hole, and then connect the red wire on the rear view
camera to the reversing light cable on the car, and connect the black wire to the
DVR. Finally, use the provided screws to fix the rearview camera in place and
- 3 -
User Manual
4M58
Important note:
The dash cam is not intended for use as a surveillance, security or
time-lapse camera system.
1. 4M58 DASH CAM(DVR) PROFILE
2. BUTTON DEFINITION
3. INSTALLATION & MOUNTING
4. FUNCTION
5. SETTING MENU
6. HOME SCREEN
7. FAQ
8. WARRANTY
1
2
3
4
5
6
7
7
- 1 -
1. 4M58 DASH CAM(DVR) PROFILE
TECHNICAL PARAMETERS
Video Resolution 1080FHD, 1080P, 720P, WVGA, VGA
Storage compression H.264
Video Format MOV
Picture Format JPG
Lens HD CMOS image sensor
DDR3 1GB
LCD Size 4.0 inches
LCD Resolution 800*480
G-SENSOR 380B
Working Power 4W
SD Card (TF) 4GB, 8GB, 16GB, 32GB, …,128GB(max)
Voltage DC 5V(1.5A)
Work Temperature -4°F~149°F(-20 ~65 )℃ ℃
Storage Temperature -13°F~167°F(-25 ~75 )℃ ℃
Air Pressure 960Mbar~1040Mbar
Battery 200mAh/3.7V lithium polymer battery
PARTS INCLUDED
Suction-cup mount
*1
DVR unit
*1
Trochilus
car charging adapter(12-24V)
*1
*1
Rear view camera
FEATURES
Private Tooling with Exclusive & Attractive Appearance.
Full HD 1080P for high Definition Video Recording.
Big Camera Lens(Diameter 1'' ) for HD Video and Photo.
170 Ultra-wide-Angle Camera provides multi-lane coverage.
High Quality Image Sensor & fill-in light for outstanding night video clarity.
Big IPS Screen 4'' for clear HD displaying and Clarify.
Dual Recording from Front & Back, Rearview camera assist parking reversing.
WDR function for HD video Clarity.
Gravity sensing, Motion detection, Parking monitor, License plate watermark.
12-24V /5V (1.5A) Car adapter with charging cable.
Works with Micro TF card 32GB(max128GB).
Suction cup mount swivels for optimal position.
Hands-free auto ON/OFF(turns ON/OFF with the vehicle).
Seamless loop Recording, Photo Taking, Replaying fuctions.
Video File Format: MOV.
- 2 -
1
Switch between Recording / Camera / Playback; When date/time
setting, press 0.5s to move the light bar to next choice; In recording
press 0.5s to lock video file.
MODE
FI
4M58 OVERVIEW
2. BUTTON DEFINITION
H
G
KTrochilus
J
LM
RESET
MIC
MODE
MENU O K
1 2 3 4 5 6A B
USB AV-IN
7 C D E
N
Definition & Operating Instructions
NO. Button/Point
LVoice broadcast
Speaker
In menu options, upward function; In standby or recording state,
picture in picture switch function.
UP
3
TF memory card slot, please install in correct direction.
FTF card slot
MENU
In standby mode, press 0.5s enter/exit setup menu; short press
(0.5s) twice to next menu-setup page;long press(3 seconds)
turn on/off fill-in light.
5
6lock the video file, to avoid being covered by loop recording.
LOCK
A RESET Resetting Key, System restart. Reset button is only used to
restore factory settings, when crashed or abnormal situation.
Microphone
MICB
plug the rearview camera.
AV IN HOLEE
The indictor light will on when energized or working.
Power/workG
H4.0'’ HD IPS Screen.
Screen
heat dissipation
I
MBracket
If there is reversing in any state, reverse image will show on the
screen.
Rear view
camera
N
Press 3s can ON/OFF the machine; press 0.5s can sleep/wake
the screen.
ON/OFF KEY
Screen Saving
7
Holder Port
D
You can choose to turn on in dark circumstance.
Fill-in light
J
In menu options, downward function; In standby or recording
state, record audio on/off.
DOWN
2
OK
Recording / camera / playback / confirmation key; In recording
mode, press 0.5s to start recording, press again to stop recording.
In camera mode, press 0.5s to taking photo; In menu mode, it’s
Enter(confirm)Key.
4
CFor providing power supply. connecting a PC to transfer data;
or power connector.
USB port
Camera LensK
4.Connect the dark red wire of camera
with reversing light. Inserting car charger machine will
automatically start recording, if there is reversing in any
state, reverse image will show on the screen. After
reversing, it will return to recording mode automatically.
3. Install and fix DVR on the front windshield;
5. Insert the adapter with charging cable in the car
cigarette lighter hole;
6. Insert the usb end of the charging cable in the DVR
usb port. Then route and hide the cable;
7. Swivel camera lens for optimal position;
8. Start car engine, format TF card, then check if DVR
installation is correct.
If correct, dash cam (DVR) indicator light will work,
and will enter recording automatically, recording
indicator light will start.
MOUNTING
INSTALLING 4M58 DASH CAM
1. Insert the hook of suction mount into the top slot of
the 4M58 as shown (A).
2. Select an area of the windshield directly above the
dash board(make sure not obstructing driving view),
then clean the area thoroughly.
3. With the suction lever in the released
position (B) press the suction cup
against the windshield (C) .Press
the suction lever toward the suction
cup to lock the mount in position (D).
4. To adjust the angle of the 4M58,
loosen the collar on the ball joint,
adjust the angle, then retighten in
the desired position (E).
3. INSTALLATION & MOUNTING
INSTALLATION
USB
power
socket
Rear view camera
1. Power off car engine;
2. Insert the right TF card in the card slot;
A
B
C
D
E
DVR
CAMERA ADJUSTMENT
The DVR camera records in one
direction. To record the view in front
of the vehicle. the camera should
face to the front windshield.
Optional:
To record the view inside of the vehicle, the camera should face the
rear window.
Sometimes should adjust camera lens direction to avoid direct sun glare.
MOUNTING REAR VIEW CAMERA
First, you need to make a hole in the rear of the car, pass the wire of the rear
view camera through this hole, and then connect the red wire on the rear view
camera to the reversing light cable on the car, and connect the black wire to the
DVR. Finally, use the provided screws to fix the rearview camera in place and
- 3 -
adjust the angle(This step may require the help of a local auto repair shop)
Plug the included Adapter into your vehicle’s Lighter socket.
Connect the adapter to the 4M58.
POWERING THE 4M58
4. FUNCTION
1. Automatic Record Function
Start car engine, dvr will start and record automatically. The charging light will
work, and the recording icon will flash on the screen. When power off car
engine, DVR will save the video file in TF card and power off automatically
following the car power off, the blue light stops flashing.
2. Manual Record Function
In standby mode and formatting TF card inside, short press (0.5s) [OK] key to
enter recording. The charging light will work, and the recording icon wil flash
on the screen. While recording, short press [OK] key to stop.
Have to choose the loop record time (1' 2' 3' 5' 10'), please prefer
1' or 3' , mustn’t choose OFF;
NOTICE:
You need to make a hole in the rear of the car,
pass the wire of the rear view camera through this
hole , and then connect the red wire and black (A)
wire on the rear view camera to the reversing light
cable on the car, and connect the black wire to the DVR. Finally, use the
provided screws to fix the rearview camera in place and adjust the angle(B)
The red wire is connected to positive pole of the
reversing light cable.
The black wire is connected to negative pole of the
reversing light cable.
(A)
(B) Red w ire
Bla ck wi re
3. Taking Photo
4. Gravity Sensor
In camera mode, short press [OK] key for 0.5s to take photo.
Built-in G-sensor can be activated and lock the key video (from 10 seconds
before accident to 3 munites after the accident) if collision happens.
- 4 -
(This step may require the help of a local auto repair shop)
5. One-click lock function
The machine has One-click lock function, it can lock the reserved files that
need to be retained without being recycled. In recording mode, short press
(0.5 Seconds) [menu], the recorder will lock the image in the first 10 seconds
and then 1/3/5 minutes.
6. Date/Time Setting
Press [MENU] key to enter Date / Time setting, short press [UP] / [DOWN] to
setup the right data, press [OK] key to confirm. press[MODE] key move the
light bar to the next item.
In order to get effectively recording date and time for prove, please
set the correct time before using the machine.
NOTICE:
7. Playback Files
Press [MODE] key to switch to playback mode on the boot state. Short press
(0.5 Seconds) “Up”/ “Down”can find the files. Short press(0.5 Seconds) “OK”
button to play.
8. Parking Monitoring
Under parking monitoring function, in shutdown status, if there is a slight
len, the video recorder will switch on automatically. It will record for 20 seconds
and then shut down if it's in the flame out state(time can be set up in the setting
menu)
9. Motion Detection
When machine turns on but In standby mode, if Motion detection is on, and the
lens senses a moving object, the machine enters the recording mode. When
the camera does not sense the moving object for 5 seconds, the system stops
recording. If you need to exit the Motion detection mode, set “off” in the [Menu].
The user must select day or night mode for best performance. The 4M58 DVR
cannot switch between day and night automatically. Long press (3 seconds)
the [MENU] button or select LIGHT SET menu to switch on or off.
10. DAY/NIGHT mode
If connecting dash camera to a computer through a USB data cable, the display
will show two options (mass storage /pc camera) (remember that you need to
insert a format memory card (TF card).Then the dash camera can be used as
MEMORY or PC CAMERA on your choice.
11. Download file
Rearview camera is optional. If with rearview camera, the dash camera will
have dual record (Front & Rearview). Besides rear image recording function,
the back camera can used as rearview system for reversing. Rearview camera
is connected with [AV IN].
12. Rearview Camera
13. Languages:
English / traditional Chinese / simplified Chinese / Japanese /French /
German / Italian / Portuguese / Russian / Spanish / Thai
5. SETTING MENU
Turn on dash camera and stop recording, press Menu key to enter setting menu.
Press DOWN/UP key to select those suitable option, finally press OK button to
confirm the operation. When all settings are complete, continue to press MENU
key to exit the setting interface.
MENU DEFINITION
- 5 -
To set video’s resolution 1080FHD, 1080P, WVGA,720P, VGA
Resolution
To adjust the light
automatically
ON, OFF.
Suggest opening full-time.
WDR
To detect moving objects
and record automatically
in standby mode
Motion
Detection On, Off
To watermark videos date
Date Stamp On, Off
Setting: In standby mode, press the Menu key twice to enter the setting
interface. select “Date/time” and press OK key to set date/time. Press
UP key / DOWN key to adjust the numbers then press OK button to
confirm. Press MODE button to move the light bar to next choice. Finally
press OK key to exit Date/Time setting to the upper menu.
Date / Time
Parking
monitor On, Off.
Menu Choice Explantion Available options
(Item with drawing line is Default)
To set video’s looping
time
1', 2', 3'(minute), 5', 10', off. if you choose
OFF, the card won’t be cyclic covering
automatically.
Loop
recording
To fill light when under-
exposed or dim screen.
+0.0, -1/3, -2/3, -1.0, -4/3, -5/3, -2.0,
+2.0, +5/3, +4/3, +1.0, +2/3, +1/3
Exposure
Compensation
To turn on/off the
Audio recording
Audio
Recording On, Off
The video of collision will
never be overwritten
G-sensor High, Middle, Low, Off
Rear Camera
Mirroring On, Off.
Off , 3 minutes, 5 minutes, 10 minutes
Auto power off
On, Off.
Beep Sound
multi-language support
Language
settings
12 Languages: English, Spanish,
Russian, French, German, Chinese…
50Hz , 60Hz.
Light source
frequency
1'(1 minute), 3', 5',Off. screen timing off
Screen Saver
Off, on
Fill-in Light
License plate
number set
Customizing for Chinese
License plate number
Displays the software version number and release schedule.
Version
When not knowing what has
changed,restore the default settings.
Default Setting Restore factory settings
Must format for first use
Format delete all the data of card
01:32:30 1080FHD+D1
2017/08/20 09:52:18 粤B88888
WDR
1234 5
6
7
8910111213
14
15
16
Playback icon, indicates the playback mode.
1. Recording standby icon, indicates the recording mode;
Red flashing indicates the device is recording.
Camera icon, indicates the photographing mode;
2. Red Font indicates the current time-imaging segment time;
01:32:30
6. Motion detection icon, when it showing in the right of the screen,
it indicates the motion is activated.
5. Small picture in the big one means there is a rearview camera is
connected for dual recording.
4.1080FHD+D1 Indicate the current select resolution is 1080FHD; D1 means
connecting one rearview camera for dual recording.
3. Loop recording segment time icon, indicating there are there 3 minutes for
recording time.
01:32:30 Yellow fond show the remaining recording time of TF card; After inserting
the memory card, in standby mode, it will show the remaining recording
time in yellow font.
7. Battery level icon: indicates the current battery level.
8. Micro SD card icon: indicates Micro SD card in the card slot.
9. Wide-Dynamic icon, when the icon showing on the screen, it indicates the
function is activated. we advise open this icon always.
WDR
10. Audio Recording;
Mute Recording.
11. Licence plate watermark function is used, and current car licence
number is .
粤B88888
粤B88888
12. Time icon, indicates the current standard time; please initial setting
before using it.
09:52:18
13. Date display, shows the current standard data, please initial
setup before using it;
2017/08/20
HOME SCREEN
All dash cameras have factory default setting. User can check all functions.
If need modification for his/her preferrence, the default setting can be modified.
Please refer to “Button Definition” & “Menu Definition” as above.
6. HOME SCREEN
14. Parking Monitoring icon: indicates the parking guard function is
activated;
15. Fill-in light open icon.
16. Lock icon means current video file is locked.
Note:
the home screen will prompt you that a memory
card is not installed.
If no TF card installed in DVR,
If a previously used SD card is formatted, all previous data will be deleted.
- 6 -
a. Reset the machine with a sharp object (such as a paperclip, pins, etc...)
inserting in the RESET hole.
b. This situation occurs mostly when over-current protection fo the machine. So
you’d avoid the machine in a car parked in the sun’s exposure for long time.
c. Reformat the TF card in the machine.
7. Fuzzy video
a. Please use the lens cloth swab dipped in alcohol or scouring oil, to wipe clean
the lens. Try to avoid touching the lens, and please keep auto glass clean.
b. Check the lens on the machine whether the protective film is removed.
If troubleshooting occurs under normal operation, please refer to the following
solutions.
1. Can't record or take photos
Solution: Please check whether the TF card has enough space, whether it is
locked or not, or the card may be broken.
2. Automatically stops when recording
Solutions: Because HD video file is big, please use the high-speed TF card
compatible with SDHC, Please use C10 or above high-speed TF card.
3. "File error" prompts when replay images and video
Solutions: Error occurred while TF card stored data, resulting in incomplete file.
Please use the "format" function of the camera to reformat the TF card.
4. The image was foggy
Solutions: Please check whether the lens has dirt or finger print. Before
shooting, wipe the lens with lens paper.
5. Horizontal stripe interference in the image
Solutions: This is due to the setting of the wrong "light source frequency",
depending on the local power supply frequency, set to "50Hz" or "60Hz".
6. Crash machine
7. FAQ
Please don’t remove or insert a memory card in boot state, to avoid
damaging the memory card.
1. Don’t follow user manual to operate product.
Exception to warranty:
2. Product damaged because of accident, neglect, abuse, misuse.
3. Repair without authorization.
4. Damaged due to transportation.
5. Other damage not because of design, technical, manufacturing and quality
problem.
All failure products should be sent to us or our authorized repair center,
attached with detail description of defect and show original purchase invoice.
WARRANTY
Warranty is 1 year counting from buying date (not include periodical
consumable part). if the product failure under normal operation, We will
provide free replacement or repair during the period of warranty. We reserve
the right to change new products or other equivalent products. We will not be
responsible for the damage(such as traffic accident) which doesn’t cause from
our products themselves.
8. Fuzzy pictures
Fix the machine on the suction cup bracket, camera shooting can achieve the
best results. But the machine itself is not a professional digital camera. Its main
use is video record.
8. WARRANTY
- 7 -
adjust the angle(This step may require the help of a local auto repair shop)
Plug the included Adapter into your vehicle’s Lighter socket.
Connect the adapter to the 4M58.
POWERING THE 4M58
4. FUNCTION
1. Automatic Record Function
Start car engine, dvr will start and record automatically. The charging light will
work, and the recording icon will flash on the screen. When power off car
engine, DVR will save the video file in TF card and power off automatically
following the car power off, the blue light stops flashing.
2. Manual Record Function
In standby mode and formatting TF card inside, short press (0.5s) [OK] key to
enter recording. The charging light will work, and the recording icon wil flash
on the screen. While recording, short press [OK] key to stop.
Have to choose the loop record time (1' 2' 3' 5' 10'), please prefer
1' or 3' , mustn’t choose OFF;
NOTICE:
You need to make a hole in the rear of the car,
pass the wire of the rear view camera through this
hole , and then connect the red wire and black (A)
wire on the rear view camera to the reversing light
cable on the car, and connect the black wire to the DVR. Finally, use the
provided screws to fix the rearview camera in place and adjust the angle(B)
The red wire is connected to positive pole of the
reversing light cable.
The black wire is connected to negative pole of the
reversing light cable.
(A)
(B) Red w ire
Bla ck wi re
3. Taking Photo
4. Gravity Sensor
In camera mode, short press [OK] key for 0.5s to take photo.
Built-in G-sensor can be activated and lock the key video (from 10 seconds
before accident to 3 munites after the accident) if collision happens.
- 4 -
(This step may require the help of a local auto repair shop)
5. One-click lock function
The machine has One-click lock function, it can lock the reserved files that
need to be retained without being recycled. In recording mode, short press
(0.5 Seconds) [menu], the recorder will lock the image in the first 10 seconds
and then 1/3/5 minutes.
6. Date/Time Setting
Press [MENU] key to enter Date / Time setting, short press [UP] / [DOWN] to
setup the right data, press [OK] key to confirm. press[MODE] key move the
light bar to the next item.
In order to get effectively recording date and time for prove, please
set the correct time before using the machine.
NOTICE:
7. Playback Files
Press [MODE] key to switch to playback mode on the boot state. Short press
(0.5 Seconds) “Up”/ “Down”can find the files. Short press(0.5 Seconds) “OK”
button to play.
8. Parking Monitoring
Under parking monitoring function, in shutdown status, if there is a slight
len, the video recorder will switch on automatically. It will record for 20 seconds
and then shut down if it's in the flame out state(time can be set up in the setting
menu)
9. Motion Detection
When machine turns on but In standby mode, if Motion detection is on, and the
lens senses a moving object, the machine enters the recording mode. When
the camera does not sense the moving object for 5 seconds, the system stops
recording. If you need to exit the Motion detection mode, set “off” in the [Menu].
The user must select day or night mode for best performance. The 4M58 DVR
cannot switch between day and night automatically. Long press (3 seconds)
the [MENU] button or select LIGHT SET menu to switch on or off.
10. DAY/NIGHT mode
If connecting dash camera to a computer through a USB data cable, the display
will show two options (mass storage /pc camera) (remember that you need to
insert a format memory card (TF card).Then the dash camera can be used as
MEMORY or PC CAMERA on your choice.
11. Download file
Rearview camera is optional. If with rearview camera, the dash camera will
have dual record (Front & Rearview). Besides rear image recording function,
the back camera can used as rearview system for reversing. Rearview camera
is connected with [AV IN].
12. Rearview Camera
13. Languages:
English / traditional Chinese / simplified Chinese / Japanese /French /
German / Italian / Portuguese / Russian / Spanish / Thai
5. SETTING MENU
Turn on dash camera and stop recording, press Menu key to enter setting menu.
Press DOWN/UP key to select those suitable option, finally press OK button to
confirm the operation. When all settings are complete, continue to press MENU
key to exit the setting interface.
MENU DEFINITION
- 5 -
To set video’s resolution 1080FHD, 1080P, WVGA,720P, VGA
Resolution
To adjust the light
automatically
ON, OFF.
Suggest opening full-time.
WDR
To detect moving objects
and record automatically
in standby mode
Motion
Detection On, Off
To watermark videos date
Date Stamp On, Off
Setting: In standby mode, press the Menu key twice to enter the setting
interface. select “Date/time” and press OK key to set date/time. Press
UP key / DOWN key to adjust the numbers then press OK button to
confirm. Press MODE button to move the light bar to next choice. Finally
press OK key to exit Date/Time setting to the upper menu.
Date / Time
Parking
monitor On, Off.
Menu Choice Explantion Available options
(Item with drawing line is Default)
To set video’s looping
time
1', 2', 3'(minute), 5', 10', off. if you choose
OFF, the card won’t be cyclic covering
automatically.
Loop
recording
To fill light when under-
exposed or dim screen.
+0.0, -1/3, -2/3, -1.0, -4/3, -5/3, -2.0,
+2.0, +5/3, +4/3, +1.0, +2/3, +1/3
Exposure
Compensation
To turn on/off the
Audio recording
Audio
Recording On, Off
The video of collision will
never be overwritten
G-sensor High, Middle, Low, Off
Rear Camera
Mirroring On, Off.
Off , 3 minutes, 5 minutes, 10 minutes
Auto power off
On, Off.
Beep Sound
multi-language support
Language
settings
12 Languages: English, Spanish,
Russian, French, German, Chinese…
50Hz , 60Hz.
Light source
frequency
1'(1 minute), 3', 5',Off. screen timing off
Screen Saver
Off, on
Fill-in Light
License plate
number set
Customizing for Chinese
License plate number
Displays the software version number and release schedule.
Version
When not knowing what has
changed,restore the default settings.
Default Setting Restore factory settings
Must format for first use
Format delete all the data of card
01:32:30 1080FHD+D1
2017/08/20 09:52:18 粤B88888
WDR
1234 5
6
7
8910111213
14
15
16
Playback icon, indicates the playback mode.
1. Recording standby icon, indicates the recording mode;
Red flashing indicates the device is recording.
Camera icon, indicates the photographing mode;
2. Red Font indicates the current time-imaging segment time;
01:32:30
6. Motion detection icon, when it showing in the right of the screen,
it indicates the motion is activated.
5. Small picture in the big one means there is a rearview camera is
connected for dual recording.
4.1080FHD+D1 Indicate the current select resolution is 1080FHD; D1 means
connecting one rearview camera for dual recording.
3. Loop recording segment time icon, indicating there are there 3 minutes for
recording time.
01:32:30 Yellow fond show the remaining recording time of TF card; After inserting
the memory card, in standby mode, it will show the remaining recording
time in yellow font.
7. Battery level icon: indicates the current battery level.
8. Micro SD card icon: indicates Micro SD card in the card slot.
9. Wide-Dynamic icon, when the icon showing on the screen, it indicates the
function is activated. we advise open this icon always.
WDR
10. Audio Recording;
Mute Recording.
11. Licence plate watermark function is used, and current car licence
number is .
粤B88888
粤B88888
12. Time icon, indicates the current standard time; please initial setting
before using it.
09:52:18
13. Date display, shows the current standard data, please initial
setup before using it;
2017/08/20
HOME SCREEN
All dash cameras have factory default setting. User can check all functions.
If need modification for his/her preferrence, the default setting can be modified.
Please refer to “Button Definition” & “Menu Definition” as above.
6. HOME SCREEN
14. Parking Monitoring icon: indicates the parking guard function is
activated;
15. Fill-in light open icon.
16. Lock icon means current video file is locked.
Note:
the home screen will prompt you that a memory
card is not installed.
If no TF card installed in DVR,
If a previously used SD card is formatted, all previous data will be deleted.
- 6 -
a. Reset the machine with a sharp object (such as a paperclip, pins, etc...)
inserting in the RESET hole.
b. This situation occurs mostly when over-current protection fo the machine. So
you’d avoid the machine in a car parked in the sun’s exposure for long time.
c. Reformat the TF card in the machine.
7. Fuzzy video
a. Please use the lens cloth swab dipped in alcohol or scouring oil, to wipe clean
the lens. Try to avoid touching the lens, and please keep auto glass clean.
b. Check the lens on the machine whether the protective film is removed.
If troubleshooting occurs under normal operation, please refer to the following
solutions.
1. Can't record or take photos
Solution: Please check whether the TF card has enough space, whether it is
locked or not, or the card may be broken.
2. Automatically stops when recording
Solutions: Because HD video file is big, please use the high-speed TF card
compatible with SDHC, Please use C10 or above high-speed TF card.
3. "File error" prompts when replay images and video
Solutions: Error occurred while TF card stored data, resulting in incomplete file.
Please use the "format" function of the camera to reformat the TF card.
4. The image was foggy
Solutions: Please check whether the lens has dirt or finger print. Before
shooting, wipe the lens with lens paper.
5. Horizontal stripe interference in the image
Solutions: This is due to the setting of the wrong "light source frequency",
depending on the local power supply frequency, set to "50Hz" or "60Hz".
6. Crash machine
7. FAQ
Please don’t remove or insert a memory card in boot state, to avoid
damaging the memory card.
1. Don’t follow user manual to operate product.
Exception to warranty:
2. Product damaged because of accident, neglect, abuse, misuse.
3. Repair without authorization.
4. Damaged due to transportation.
5. Other damage not because of design, technical, manufacturing and quality
problem.
All failure products should be sent to us or our authorized repair center,
attached with detail description of defect and show original purchase invoice.
WARRANTY
Warranty is 1 year counting from buying date (not include periodical
consumable part). if the product failure under normal operation, We will
provide free replacement or repair during the period of warranty. We reserve
the right to change new products or other equivalent products. We will not be
responsible for the damage(such as traffic accident) which doesn’t cause from
our products themselves.
8. Fuzzy pictures
Fix the machine on the suction cup bracket, camera shooting can achieve the
best results. But the machine itself is not a professional digital camera. Its main
use is video record.
8. WARRANTY
- 7 -
adjust the angle(This step may require the help of a local auto repair shop)
Plug the included Adapter into your vehicle’s Lighter socket.
Connect the adapter to the 4M58.
POWERING THE 4M58
4. FUNCTION
1. Automatic Record Function
Start car engine, dvr will start and record automatically. The charging light will
work, and the recording icon will flash on the screen. When power off car
engine, DVR will save the video file in TF card and power off automatically
following the car power off, the blue light stops flashing.
2. Manual Record Function
In standby mode and formatting TF card inside, short press (0.5s) [OK] key to
enter recording. The charging light will work, and the recording icon wil flash
on the screen. While recording, short press [OK] key to stop.
Have to choose the loop record time (1' 2' 3' 5' 10'), please prefer
1' or 3' , mustn’t choose OFF;
NOTICE:
You need to make a hole in the rear of the car,
pass the wire of the rear view camera through this
hole , and then connect the red wire and black (A)
wire on the rear view camera to the reversing light
cable on the car, and connect the black wire to the DVR. Finally, use the
provided screws to fix the rearview camera in place and adjust the angle(B)
The red wire is connected to positive pole of the
reversing light cable.
The black wire is connected to negative pole of the
reversing light cable.
(A)
(B) Red w ire
Bla ck wi re
3. Taking Photo
4. Gravity Sensor
In camera mode, short press [OK] key for 0.5s to take photo.
Built-in G-sensor can be activated and lock the key video (from 10 seconds
before accident to 3 munites after the accident) if collision happens.
- 4 -
(This step may require the help of a local auto repair shop)
5. One-click lock function
The machine has One-click lock function, it can lock the reserved files that
need to be retained without being recycled. In recording mode, short press
(0.5 Seconds) [menu], the recorder will lock the image in the first 10 seconds
and then 1/3/5 minutes.
6. Date/Time Setting
Press [MENU] key to enter Date / Time setting, short press [UP] / [DOWN] to
setup the right data, press [OK] key to confirm. press[MODE] key move the
light bar to the next item.
In order to get effectively recording date and time for prove, please
set the correct time before using the machine.
NOTICE:
7. Playback Files
Press [MODE] key to switch to playback mode on the boot state. Short press
(0.5 Seconds) “Up”/ “Down”can find the files. Short press(0.5 Seconds) “OK”
button to play.
8. Parking Monitoring
Under parking monitoring function, in shutdown status, if there is a slight
len, the video recorder will switch on automatically. It will record for 20 seconds
and then shut down if it's in the flame out state(time can be set up in the setting
menu)
9. Motion Detection
When machine turns on but In standby mode, if Motion detection is on, and the
lens senses a moving object, the machine enters the recording mode. When
the camera does not sense the moving object for 5 seconds, the system stops
recording. If you need to exit the Motion detection mode, set “off” in the [Menu].
The user must select day or night mode for best performance. The 4M58 DVR
cannot switch between day and night automatically. Long press (3 seconds)
the [MENU] button or select LIGHT SET menu to switch on or off.
10. DAY/NIGHT mode
If connecting dash camera to a computer through a USB data cable, the display
will show two options (mass storage /pc camera) (remember that you need to
insert a format memory card (TF card).Then the dash camera can be used as
MEMORY or PC CAMERA on your choice.
11. Download file
Rearview camera is optional. If with rearview camera, the dash camera will
have dual record (Front & Rearview). Besides rear image recording function,
the back camera can used as rearview system for reversing. Rearview camera
is connected with [AV IN].
12. Rearview Camera
13. Languages:
English / traditional Chinese / simplified Chinese / Japanese /French /
German / Italian / Portuguese / Russian / Spanish / Thai
5. SETTING MENU
Turn on dash camera and stop recording, press Menu key to enter setting menu.
Press DOWN/UP key to select those suitable option, finally press OK button to
confirm the operation. When all settings are complete, continue to press MENU
key to exit the setting interface.
MENU DEFINITION
- 5 -
To set video’s resolution 1080FHD, 1080P, WVGA,720P, VGA
Resolution
To adjust the light
automatically
ON, OFF.
Suggest opening full-time.
WDR
To detect moving objects
and record automatically
in standby mode
Motion
Detection On, Off
To watermark videos date
Date Stamp On, Off
Setting: In standby mode, press the Menu key twice to enter the setting
interface. select “Date/time” and press OK key to set date/time. Press
UP key / DOWN key to adjust the numbers then press OK button to
confirm. Press MODE button to move the light bar to next choice. Finally
press OK key to exit Date/Time setting to the upper menu.
Date / Time
Parking
monitor On, Off.
Menu Choice Explantion Available options
(Item with drawing line is Default)
To set video’s looping
time
1', 2', 3'(minute), 5', 10', off. if you choose
OFF, the card won’t be cyclic covering
automatically.
Loop
recording
To fill light when under-
exposed or dim screen.
+0.0, -1/3, -2/3, -1.0, -4/3, -5/3, -2.0,
+2.0, +5/3, +4/3, +1.0, +2/3, +1/3
Exposure
Compensation
To turn on/off the
Audio recording
Audio
Recording On, Off
The video of collision will
never be overwritten
G-sensor High, Middle, Low, Off
Rear Camera
Mirroring On, Off.
Off , 3 minutes, 5 minutes, 10 minutes
Auto power off
On, Off.
Beep Sound
multi-language support
Language
settings
12 Languages: English, Spanish,
Russian, French, German, Chinese…
50Hz , 60Hz.
Light source
frequency
1'(1 minute), 3', 5',Off. screen timing off
Screen Saver
Off, on
Fill-in Light
License plate
number set
Customizing for Chinese
License plate number
Displays the software version number and release schedule.
Version
When not knowing what has
changed,restore the default settings.
Default Setting Restore factory settings
Must format for first use
Format delete all the data of card
01:32:30 1080FHD+D1
2017/08/20 09:52:18 粤B88888
WDR
1234 5
6
7
8910111213
14
15
16
Playback icon, indicates the playback mode.
1. Recording standby icon, indicates the recording mode;
Red flashing indicates the device is recording.
Camera icon, indicates the photographing mode;
2. Red Font indicates the current time-imaging segment time;
01:32:30
6. Motion detection icon, when it showing in the right of the screen,
it indicates the motion is activated.
5. Small picture in the big one means there is a rearview camera is
connected for dual recording.
4.1080FHD+D1 Indicate the current select resolution is 1080FHD; D1 means
connecting one rearview camera for dual recording.
3. Loop recording segment time icon, indicating there are there 3 minutes for
recording time.
01:32:30 Yellow fond show the remaining recording time of TF card; After inserting
the memory card, in standby mode, it will show the remaining recording
time in yellow font.
7. Battery level icon: indicates the current battery level.
8. Micro SD card icon: indicates Micro SD card in the card slot.
9. Wide-Dynamic icon, when the icon showing on the screen, it indicates the
function is activated. we advise open this icon always.
WDR
10. Audio Recording;
Mute Recording.
11. Licence plate watermark function is used, and current car licence
number is .
粤B88888
粤B88888
12. Time icon, indicates the current standard time; please initial setting
before using it.
09:52:18
13. Date display, shows the current standard data, please initial
setup before using it;
2017/08/20
HOME SCREEN
All dash cameras have factory default setting. User can check all functions.
If need modification for his/her preferrence, the default setting can be modified.
Please refer to “Button Definition” & “Menu Definition” as above.
6. HOME SCREEN
14. Parking Monitoring icon: indicates the parking guard function is
activated;
15. Fill-in light open icon.
16. Lock icon means current video file is locked.
Note:
the home screen will prompt you that a memory
card is not installed.
If no TF card installed in DVR,
If a previously used SD card is formatted, all previous data will be deleted.
- 6 -
a. Reset the machine with a sharp object (such as a paperclip, pins, etc...)
inserting in the RESET hole.
b. This situation occurs mostly when over-current protection fo the machine. So
you’d avoid the machine in a car parked in the sun’s exposure for long time.
c. Reformat the TF card in the machine.
7. Fuzzy video
a. Please use the lens cloth swab dipped in alcohol or scouring oil, to wipe clean
the lens. Try to avoid touching the lens, and please keep auto glass clean.
b. Check the lens on the machine whether the protective film is removed.
If troubleshooting occurs under normal operation, please refer to the following
solutions.
1. Can't record or take photos
Solution: Please check whether the TF card has enough space, whether it is
locked or not, or the card may be broken.
2. Automatically stops when recording
Solutions: Because HD video file is big, please use the high-speed TF card
compatible with SDHC, Please use C10 or above high-speed TF card.
3. "File error" prompts when replay images and video
Solutions: Error occurred while TF card stored data, resulting in incomplete file.
Please use the "format" function of the camera to reformat the TF card.
4. The image was foggy
Solutions: Please check whether the lens has dirt or finger print. Before
shooting, wipe the lens with lens paper.
5. Horizontal stripe interference in the image
Solutions: This is due to the setting of the wrong "light source frequency",
depending on the local power supply frequency, set to "50Hz" or "60Hz".
6. Crash machine
7. FAQ
Please don’t remove or insert a memory card in boot state, to avoid
damaging the memory card.
1. Don’t follow user manual to operate product.
Exception to warranty:
2. Product damaged because of accident, neglect, abuse, misuse.
3. Repair without authorization.
4. Damaged due to transportation.
5. Other damage not because of design, technical, manufacturing and quality
problem.
All failure products should be sent to us or our authorized repair center,
attached with detail description of defect and show original purchase invoice.
WARRANTY
Warranty is 1 year counting from buying date (not include periodical
consumable part). if the product failure under normal operation, We will
provide free replacement or repair during the period of warranty. We reserve
the right to change new products or other equivalent products. We will not be
responsible for the damage(such as traffic accident) which doesn’t cause from
our products themselves.
8. Fuzzy pictures
Fix the machine on the suction cup bracket, camera shooting can achieve the
best results. But the machine itself is not a professional digital camera. Its main
use is video record.
8. WARRANTY
- 7 -
adjust the angle(This step may require the help of a local auto repair shop)
Plug the included Adapter into your vehicle’s Lighter socket.
Connect the adapter to the 4M58.
POWERING THE 4M58
4. FUNCTION
1. Automatic Record Function
Start car engine, dvr will start and record automatically. The charging light will
work, and the recording icon will flash on the screen. When power off car
engine, DVR will save the video file in TF card and power off automatically
following the car power off, the blue light stops flashing.
2. Manual Record Function
In standby mode and formatting TF card inside, short press (0.5s) [OK] key to
enter recording. The charging light will work, and the recording icon wil flash
on the screen. While recording, short press [OK] key to stop.
Have to choose the loop record time (1' 2' 3' 5' 10'), please prefer
1' or 3' , mustn’t choose OFF;
NOTICE:
You need to make a hole in the rear of the car,
pass the wire of the rear view camera through this
hole , and then connect the red wire and black (A)
wire on the rear view camera to the reversing light
cable on the car, and connect the black wire to the DVR. Finally, use the
provided screws to fix the rearview camera in place and adjust the angle(B)
The red wire is connected to positive pole of the
reversing light cable.
The black wire is connected to negative pole of the
reversing light cable.
(A)
(B) Red w ire
Bla ck wir e
3. Taking Photo
4. Gravity Sensor
In camera mode, short press [OK] key for 0.5s to take photo.
Built-in G-sensor can be activated and lock the key video (from 10 seconds
before accident to 3 munites after the accident) if collision happens.
- 4 -
(This step may require the help of a local auto repair shop)
5. One-click lock function
The machine has One-click lock function, it can lock the reserved files that
need to be retained without being recycled. In recording mode, short press
(0.5 Seconds) [menu], the recorder will lock the image in the first 10 seconds
and then 1/3/5 minutes.
6. Date/Time Setting
Press [MENU] key to enter Date / Time setting, short press [UP] / [DOWN] to
setup the right data, press [OK] key to confirm. press[MODE] key move the
light bar to the next item.
In order to get effectively recording date and time for prove, please
set the correct time before using the machine.
NOTICE:
7. Playback Files
Press [MODE] key to switch to playback mode on the boot state. Short press
(0.5 Seconds) “Up”/ “Down”can find the files. Short press(0.5 Seconds) “OK”
button to play.
8. Parking Monitoring
Under parking monitoring function, in shutdown status, if there is a slight
len, the video recorder will switch on automatically. It will record for 20 seconds
and then shut down if it's in the flame out state(time can be set up in the setting
menu)
9. Motion Detection
When machine turns on but In standby mode, if Motion detection is on, and the
lens senses a moving object, the machine enters the recording mode. When
the camera does not sense the moving object for 5 seconds, the system stops
recording. If you need to exit the Motion detection mode, set “off” in the [Menu].
The user must select day or night mode for best performance. The 4M58 DVR
cannot switch between day and night automatically. Long press (3 seconds)
the [MENU] button or select LIGHT SET menu to switch on or off.
10. DAY/NIGHT mode
If connecting dash camera to a computer through a USB data cable, the display
will show two options (mass storage /pc camera) (remember that you need to
insert a format memory card (TF card).Then the dash camera can be used as
MEMORY or PC CAMERA on your choice.
11. Download file
Rearview camera is optional. If with rearview camera, the dash camera will
have dual record (Front & Rearview). Besides rear image recording function,
the back camera can used as rearview system for reversing. Rearview camera
is connected with [AV IN].
12. Rearview Camera
13. Languages:
English / traditional Chinese / simplified Chinese / Japanese /French /
German / Italian / Portuguese / Russian / Spanish / Thai
5. SETTING MENU
Turn on dash camera and stop recording, press Menu key to enter setting menu.
Press DOWN/UP key to select those suitable option, finally press OK button to
confirm the operation. When all settings are complete, continue to press MENU
key to exit the setting interface.
MENU DEFINITION
- 5 -
To set video’s resolution 1080FHD, 1080P, WVGA,720P, VGA
Resolution
To adjust the light
automatically
ON, OFF.
Suggest opening full-time.
WDR
To detect moving objects
and record automatically
in standby mode
Motion
Detection On, Off
To watermark videos date
Date Stamp On, Off
Setting: In standby mode, press the Menu key twice to enter the setting
interface. select “Date/time” and press OK key to set date/time. Press
UP key / DOWN key to adjust the numbers then press OK button to
confirm. Press MODE button to move the light bar to next choice. Finally
press OK key to exit Date/Time setting to the upper menu.
Date / Time
Parking
monitor On, Off.
Menu Choice Explantion Available options
(Item with drawing line is Default)
To set video’s looping
time
1', 2', 3'(minute), 5', 10', off. if you choose
OFF, the card won’t be cyclic covering
automatically.
Loop
recording
To fill light when under-
exposed or dim screen.
+0.0, -1/3, -2/3, -1.0, -4/3, -5/3, -2.0,
+2.0, +5/3, +4/3, +1.0, +2/3, +1/3
Exposure
Compensation
To turn on/off the
Audio recording
Audio
Recording On, Off
The video of collision will
never be overwritten
G-sensor High, Middle, Low, Off
Rear Camera
Mirroring On, Off.
Off , 3 minutes, 5 minutes, 10 minutes
Auto power off
On, Off.
Beep Sound
multi-language support
Language
settings
12 Languages: English, Spanish,
Russian, French, German, Chinese…
50Hz , 60Hz.
Light source
frequency
1'(1 minute), 3', 5',Off. screen timing off
Screen Saver
Off, on
Fill-in Light
License plate
number set
Customizing for Chinese
License plate number
Displays the software version number and release schedule.
Version
When not knowing what has
changed,restore the default settings.
Default Setting Restore factory settings
Must format for first use
Format delete all the data of card
01:32:30 1080FHD+D1
2017/08/20 09:52:18 粤B88888
WDR
1234 5
6
7
8910111213
14
15
16
Playback icon, indicates the playback mode.
1. Recording standby icon, indicates the recording mode;
Red flashing indicates the device is recording.
Camera icon, indicates the photographing mode;
2. Red Font indicates the current time-imaging segment time;
01:32:30
6. Motion detection icon, when it showing in the right of the screen,
it indicates the motion is activated.
5. Small picture in the big one means there is a rearview camera is
connected for dual recording.
4.1080FHD+D1 Indicate the current select resolution is 1080FHD; D1 means
connecting one rearview camera for dual recording.
3. Loop recording segment time icon, indicating there are there 3 minutes for
recording time.
01:32:30 Yellow fond show the remaining recording time of TF card; After inserting
the memory card, in standby mode, it will show the remaining recording
time in yellow font.
7. Battery level icon: indicates the current battery level.
8. Micro SD card icon: indicates Micro SD card in the card slot.
9. Wide-Dynamic icon, when the icon showing on the screen, it indicates the
function is activated. we advise open this icon always.
WDR
10. Audio Recording;
Mute Recording.
11. Licence plate watermark function is used, and current car licence
number is .
粤B88888
粤B88888
12. Time icon, indicates the current standard time; please initial setting
before using it.
09:52:18
13. Date display, shows the current standard data, please initial
setup before using it;
2017/08/20
HOME SCREEN
All dash cameras have factory default setting. User can check all functions.
If need modification for his/her preferrence, the default setting can be modified.
Please refer to “Button Definition” & “Menu Definition” as above.
6. HOME SCREEN
14. Parking Monitoring icon: indicates the parking guard function is
activated;
15. Fill-in light open icon.
16. Lock icon means current video file is locked.
Note:
the home screen will prompt you that a memory
card is not installed.
If no TF card installed in DVR,
If a previously used SD card is formatted, all previous data will be deleted.
- 6 -
a. Reset the machine with a sharp object (such as a paperclip, pins, etc...)
inserting in the RESET hole.
b. This situation occurs mostly when over-current protection fo the machine. So
you’d avoid the machine in a car parked in the sun’s exposure for long time.
c. Reformat the TF card in the machine.
7. Fuzzy video
a. Please use the lens cloth swab dipped in alcohol or scouring oil, to wipe clean
the lens. Try to avoid touching the lens, and please keep auto glass clean.
b. Check the lens on the machine whether the protective film is removed.
If troubleshooting occurs under normal operation, please refer to the following
solutions.
1. Can't record or take photos
Solution: Please check whether the TF card has enough space, whether it is
locked or not, or the card may be broken.
2. Automatically stops when recording
Solutions: Because HD video file is big, please use the high-speed TF card
compatible with SDHC, Please use C10 or above high-speed TF card.
3. "File error" prompts when replay images and video
Solutions: Error occurred while TF card stored data, resulting in incomplete file.
Please use the "format" function of the camera to reformat the TF card.
4. The image was foggy
Solutions: Please check whether the lens has dirt or finger print. Before
shooting, wipe the lens with lens paper.
5. Horizontal stripe interference in the image
Solutions: This is due to the setting of the wrong "light source frequency",
depending on the local power supply frequency, set to "50Hz" or "60Hz".
6. Crash machine
7. FAQ
Please don’t remove or insert a memory card in boot state, to avoid
damaging the memory card.
1. Don’t follow user manual to operate product.
Exception to warranty:
2. Product damaged because of accident, neglect, abuse, misuse.
3. Repair without authorization.
4. Damaged due to transportation.
5. Other damage not because of design, technical, manufacturing and quality
problem.
All failure products should be sent to us or our authorized repair center,
attached with detail description of defect and show original purchase invoice.
WARRANTY
Warranty is 1 year counting from buying date (not include periodical
consumable part). if the product failure under normal operation, We will
provide free replacement or repair during the period of warranty. We reserve
the right to change new products or other equivalent products. We will not be
responsible for the damage(such as traffic accident) which doesn’t cause from
our products themselves.
8. Fuzzy pictures
Fix the machine on the suction cup bracket, camera shooting can achieve the
best results. But the machine itself is not a professional digital camera. Its main
use is video record.
8. WARRANTY
- 7 -
Table of contents
Other Sunwayi Dashcam manuals
