70mai M500 User manual

70mai Dash Cam M500 User Manual

01
Product overview
Please read this manual carefully before using the product and keep it in a safe place.
Note: Illustrations of the product, accessories, and user interface in the user manual are for reference purposes only. The actual product and functions may vary due to
product enhancements.
①① Type-C power portType-C power port
② Camera
③ Microphone
④ Ventilation holes
⑤ Indicator
⑥ Power button
⑦ Heat resistant adhesive
⑧⑧ MountMount
⑨⑨ Power cord holePower cord hole
2. Inserting the dash cam into the bracket
Insert the dash dam into the bracket with the power port facing inside until you hear a click sound.
And then the dash cam is well installed.
Installation
1. Installing the electrostatic sticker
Clean your windshield and put the electrostatic sticker on the recommended area as shown in the
figure. Avoid the edge of the windshield and select the flat and smooth area for the installation.
Make sure you remove air bubbles between the sticker and the glass.

02
3. Connecting the power cord
Connect the power cord to the Type-C power portType-C power port of the dasm cam. Pull the power cord to make
sure that it is well connected.
5. Connecting the power supply
As shown in the figure, run the power cord along the top of the windshield, down the A-pillar, and
around the glove compartment, so that the power connector is near the cigarette lighter. Connect
the power cord to the car charger, then plug the charger into the cigarette lighter socket.
Notes:
● Use the included crowbar to hide the power cord underneath the vehicle’s headliner and rubber seal
along the A-pillar.
● Depending on the vehicle, the cigarette lighter socket may be located in a different position. The figure
provided is for reference only.
6. Adjusting the dash cam angle
Connect the dash cam with the 70mai app following the instructions on the user guide.
Turn on the dash cam and adjust the camera angle based on the preview screen on the app.
4. Pasting the bracket
Rotate the mount of the bracket and make the heat resistant adhesive face toward the front
windshield.
Peel off the protective film from the heat resistant adhesive, and paste the bracket on the
electrostatic sticker in the dotted area.
Press the mount to make sure it is firmly attached on the electrostatic sticker.

03
Button functions
Press the power button a different number of times to perform different functions.
Status Operation Function
Turned off Press once Turn on the device
Turned on
Press once Turn on/off Wi-Fi
Press 4 times in a row Format the built-in memory card
Press 5 times in a row Reset factory settings
Press and hold for about 3 seconds Turn off the device
Receiving the connection request Press once Confirm the connection authorization
During the operation process Press and hold for about 15 seconds Force shut down the device
Connecting with 70mai app
This product needs to be used in conjunction with the 70mai app. Use your phone to search for "70mai" in the app stores
or scan the QR code listed here to download and install the app.
Note: Android 4.4 & iOS 9.0 or above is required to connect to the dash cam’s Wi-Fi hotspot with a mobile phone.
Refer to the user guide for how to establish a connection.
70mai Dash Cam M500 Wi-Fi hotspot information:
●Hotspot name: 70mai_M500_XXXX (You can find the hotspot name on the label of the device.)
●Default password: 12345678
User guide
Scan the QR code to access the user guide. The guide provides detailed product information including descriptions of
functions. Read this guide carefully before use in order to avoid damage due to incorrect use.

04
Voice control
Dash cam supports voice control. During the operation of the dash cam, the voice commands from the user will trigger the relevant functions of the
dash cam.
Please note that this dash cam only supports English voice commands, and the system language of the dash cam should be set to English before using
the voice control function.
The supported voice commands are as follows:
Voice command Function
Take a photo Dash cam will take a photo and save it to the album.
Shoot a video Dash cam will record an emergency video and store it in the emergency video directory.
Enable sound recording Dash cam will record audio as well as videos.
Disable sound recording Dash cam will not record audio but only videos.
Open hotspot Dash cam's Wi-Fi hotspot will be turned on.
Close hotspot Dash cam's Wi-Fi hotspot will be turned off.
Note: When the dash cam is connected to the 70mai app, voice command is not supported.
Specifications
Product: Dash Cam
Model: M500
Resolution: 2592 × 1944
Lens: FOV 170°/ F2.0
Input: 5V 2A
Power supply: Car cigarette lighter
Battery type:Li-ion battery
Packing list
1. 70mai Dash Cam M500 × 1
2. Power cord × 1
3. Dual USB car charger × 1
4. Bracket × 1
5. Electrostatic sticker × 1
6. Wiring crowbar × 1
7. Adhesive sticker × 1
8. User manual × 1