SUPER-CAN LD611-54031 User manual

LED PAR 54x3in1 RGB
LD611-54031
User Manual
This product manual contains important information about the safe installation
and use of this product.Please read and follow these instruction carefully and
keep this manual in a safe place for future reference.

- 1 -
1Understanding of Product
1.1 Security Warning
When unpacking and before disposing of the carton, check if there is any transportation damage
before using the product. Should there be any damage caused by transportation, consult your
dealer and do not use the apparatus.
This product is suitable for indoor and outdoor, its protection grade is IP65.
Do not install the product or project the beam onto inflammable surfaces. Minimum distance is 5 M
.
The product is only intended for installation, operation and maintenance by qualified personnel.
And read the user manual and labels on the lighting carefully before use.
Product should install in a cool place. Keep away from the wall 50cm.
Do not look directly at the lamp light (especially for epilepsy), so as not to cause damage to the
eyes.
Keep the optical system clean. Do not touch the LED lens with bare hands. Do not use any alcohol
liquid or any other liquid to clean the optical system. Use medicinal absorbent cotton to clean it.
Please do not attempt to dismantle and/or modify the product inner structure. Otherwise, would not
provide 1 year of free warranty.
Electrical connection must only be carried out by qualified personnel.
Before installation, ensure that the voltage and frequency of power supply match the power
requirement of the product.
It is essential that each product is correctly earthed and that electrical installation conforms to all
relevant standards.
Do not connect this device to any other types of dimmer apparatus.
Make sure that the power-cord is never crimped or damaged by sharp edges.Never let the
power-cord come into contact with other cables. Only handle the power-cord by the plug.Never pull
out the plug by tugging the power-cord.
There is no user serviceable parts inside the product, do not open the housing and never operate
the product with the cover removed.
Place the unit where kids can't reach.
If you have any questions,don't hesitate to consult our dealer or manufacturer.
Important: Before any installation, maintenance and cleaning, please
ensure that the power cut off!

- 2 -
1.2Main Technical Parameters
Power supply
Rated Voltage: AC90~240V
Rated Frequency: 50~60Hz ±10%
Rated Power: 200W
LED
LED Type: 54pcs ×3in1 RGB Chips
Drive Current: 2700mA x 3
Colors: 2563(0~100% Dimming)
Life: About 50,000 hours
Control
Control Protocol: standard DMX-512 signal
Channel Mode: 3CHS/4CHS/5CHS/6CHS/9CHS
Control Mode: DMX-512, auto mode, master-slave mode, static mode
Auto Effect: 5 kinds of auto effects
Optical System
Dimming mode: Dimmer 0: Normal dimming. Dimmer [X]: fading speed.
Dimmer: 0~100% linear dimming.
Strobe rate: 1~20Hz
Beam angle: 25°
Physical
Dimensions: 294 x 220 x 324mm
Net Weight: 2.5kgs
Surface Treatment: Aluminum die casting, powder coating
Housing color: Black
Connection: DMX cable IN/OUT, Power cable IN/OUT
Security
Cooling System: Convection
Operating Environment: Indoor
Working Temperature:-20°C～40°C

- 3 -
1.3 Product Features
Using latest LED control technique, newest intelligent LED Par light can realize intelligent operation and
control through its special menu at the backside. It’s more convenient and easy to operate.This product
is designed for building large area spread light,large concerts, outdoor landscape lighting, wedding
scene, small performances, slow club KTV and various performance occasion. Its main features include:
1) Static color Settings (STATIC).
2) The static power consumption of the control panel is 0.3W, and its efficiency will reach up to 97%
3) 4K refresh rate, get rid of the dark fringe or waves during taking the videos .
4) Linear dimming and nonlinear dimming (DIMMER).
5) Overheating protection function
6) LED display screen.
7) 5 kinds DMX working mode.
9) Master-slave control, multi-units for synchronous control.
2Product Installation
2.1 Power Connection Method
Please connect power as following ：
L（live wire）=brown wire E（earth wire）=yellow/green double color wire N（null line）=blue wire
When connecting power, ensure that the voltage and frequency of power supply match the power
requirement of the product.
This equipment belong to class 1 protection equipment, therefore, the yellow-green double colors wire
must be earthed correctly by qualified personnel. Before installation, ensure that the voltage and
frequency of power supply match the power requirements of product. In power supply and voltage
fluctuation large areas, we suggest you to use 110V or 230V or use voltage regulator to supply power.
After electrical connection, this product will have a few seconds self-check action, self-check finished
can be used.
Input / output power cable diameter 2.5mm2 (13AWG).
AC220V: can be connected 15 units in series.
AC110V: can be connected 7 units in series.
Important: It is essential that Yellow/green double color wire is correctly earthed
and that electrical installation conforms to all relevant standards.

- 4 -
2.2 DMX Connection Method
2.2--1 When you set the DMX512 address code,, as below:
The DMX interface of lamp needs be connected to the
DMX controller
DMX address from 001 to 512.
Note: 1. As this fixture's DMX signal cable connection is Parallel
connection, please don’t more than 15 units.
2. If the signal cable is over 60m between the DMX512 controller
And fixture or between two fixtures, then a DMX signal amplifier
is needed.
3Operation Method
3.1 Control panel functions introduction
MENU：Menu button/return button, enter the menu selection interface or previous menu.
ENTER：Confirmation button, used to confirm the selected function.
UP/DOWN：Upward/downward select function or Parameter increment / decrement.

- 5 -
3.2 Menu Overview
3.3 Static Color Setting (STATIC)
Find【STATIC】menu and press【ENTER】to enter color static setting.
Press【ENTER】button to select【RED】,【GREEN】,【BLUE】, or【STROBE】.
Press【UP/DOWN】button to adjust parameters.
Press【MENU】button to return to the menu, the selected parameters will be automatically saved.
After setting lighting fixture's static color, restart the lighting fixture's power supply. The setting was
preserved. Exit menu, static color setting will be removed.
Note: When entered this submenu, the light fixture will automatically set
to the data status sent by the master, other light fixtures should be set as
the slave. Then,any other master lighting fixtures must be disconnected,
as well as the DMX signal cables. Otherwise it will cause disordering.

- 6 -
3.4 Automatic Programming Setting (AUTO)
Find【AUTO】menu and press【ENTER】to enter automatic programming setting.
Press【UP/DOWN】button to select【AT.01~05】5 kinds of auto-program.【PT.01~10】10 kinds of
programmable. Press【ENTER】to confirm your setting.
After setting lighting fixture's automatic operation,restart the lighting fixture's power supply.The
setting was preserved.Exit menu,automatic operation setting will be removed.
Note: When entered this submenu, the light fixture will automatically set
to the data status sent by the master, other light fixtures should be set as
the slave. Then,any other master lighting fixtures must be disconnected,
as well as the DMX signal cables. Otherwise it will cause disordering.
3.5 DMX code setting (DMX)
Find【DMX】menu and press【ENTER】to enter address code setting.
Press【UP/DOWN】button to select DMX address code.
Press【ENTER】to confirm or【MENU】to exit, the selected address code will be automatically saved.

- 7 -
3.6 DMX Channel Mode setting (PERS)
Find【PERS】menu and press【ENTER】to enter DMX channel mode setting.
Press【UP/DOWN】button to select【8CH, ARC.1……】5 kinds DMX channel modes.
Press【ENTER】to confirm or【MENU】to exit.The setting will be automatically saved.
3.7 Function Settings (SET)
Find【SET】menu and press【ENTER】to enter function setting.
Press【UP/DOWN】button to select【REST】restore factory settings,【ID】ID function setting,【DIM】
dimming mode setting.
【REST】restore factory settings, function settings and parameters will restore the factory settings.
【DIM】dimming mode setting,【OFF】means non-linear dimming closed,【DIM1~9】means 9 kinds
of non-dimming speed optional.
Press【ENTER】to confirm or【MENU】to exit and save the setting.

- 8 -
3.8 Temperature control protection State
When the temperature of the LED bead plate more than 65℃, the driver current begin slow down,to
protect the LED Chips bead is not damaged by high temperature heat aging.
4Control Channel
4.1----3CH 3CH Mode:
Channel
DMX Data
Control function
Detail description
1
0 255
Red dimmer
Brightness 0~100%
2
0 255
Green dimmer
Brightness 0~100%
3
0 255
Blue dimmer
Brightness 0~100%
4.2----ARC.3 4CH Mode:
Channel
DMX Data
Control function
Detail description
1
0 255
Red dimmer
Brightness 0~100%
2
0 255
Green dimmer
Brightness 0~100%
3
0 255
Blue dimmer
Brightness 0~100%
4
0 09
NO FUNCTION
10 34
Linear dimming speed (DIM=OFF)
Fading speed
35 59
Non-linear dimming speed1 (DIM=1)
Fading speed
60 84
Non-linear dimming speed2 (DIM=2)
Fading speed
85 109
Non-linear dimming speed3 (DIM=3)
Fading speed
110 134
Non-linear dimming speed4 (DIM=4)
Fading speed
135 159
Non-linear dimming speed5 (DIM=5)
Fading speed
101 150
Non-linear dimming speed6 (DIM=6)
Fading speed
151 200
Non-linear dimming speed7 (DIM=7)
Fading speed
201 255
Non-linear dimming speed8 (DIM=8)
Fading speed

- 9 -
4.3----ARC.3+D 5CH Mode:
Channel
DMX Data
Control function
Detail description
1
0 255
Over dimmer
Brightness 0~100%
2
0 255
Red dimmer
Brightness 0~100%
3
0 255
Green dimmer
Brightness 0~100%
4
0 255
Blue dimmer
Brightness 0~100%
5
0 09
NO FUNCTION
10 34
Linear dimming speed (DIM=OFF)
Fading speed
35 59
Non-linear dimming speed1 (DIM=1)
Fading speed
60 84
Non-linear dimming speed2 (DIM=2)
Fading speed
85 109
Non-linear dimming speed3 (DIM=3)
Fading speed
110 134
Non-linear dimming speed4 (DIM=4)
Fading speed
135 159
Non-linear dimming speed5 (DIM=5)
Fading speed
160 184
Non-linear dimming speed6 (DIM=6)
Fading speed
185 209
Non-linear dimming speed7 (DIM=7)
Fading speed
210 255
Non-linear dimming speed8 (DIM=8)
Fading speed
4.4----ARC.3+S 6CH Mode:
Channel
DMX Data
Control function
Detail description
1
0 255
Over dimmer
Brightness 0~100%
2
0 255
Red dimmer
Brightness 0~100%
3
0 255
Green dimmer
Brightness 0~100%
4
0 255
Blue dimmer
Brightness 0~100%
5
0 9
NO FUNCTION
Strobe
10 49
Synchronous slow strobe
50 99
Asynchronous slow strobe
100 149
Random slow strobe
150 199
Asynchronous fast strobe
200 255
Synchronous fast strobe
6
0 50
Linear dimming speed (DIM=OFF)
Fading speed
51 100
Non-linear dimming speed1 (DIM=1)
Fading speed
101 150
Non-linear dimming speed2 (DIM=2)
Fading speed
151 200
Non-linear dimming speed3 (DIM=3)
Fading speed
201 255
Non-linear dimming speed4 (DIM=4)
Fading speed

- 10 -
4.5----STAG 9CH mode:
CHs
DMX data
Functions
Descriptions
1
0 255
Overall Dimmer
Brightness 0~100%
2
0 255
Red Dimmer
Brightness 0~100%
3
0 255
Green Dimmer
Brightness 0~100%
4
0 255
Blue Dimmer
Brightness 0~100%
5
0 9
NO FUNCTION
COLOR MACRO
10 29
RED 100％/GREEN UP/BLUE 0％
30 49
RED DOWN/GREEN 100％/BLUE 0％
50 69
RED 0％/GREEN 100％/BLUE UP
70 89
RED 0％/GREEN DOWN/BLUE 100％
90 109
RED UP/GREEN 0％/BLUE 100％
110 129
RED 100％/GREEN 0％/BLUE DOWN
130 149
RED 100％/GREEN UP /BLUE UP
150 169
Red DOWN /Green DOWN /Blue 100％
170 255
Red 100％/Green 100％/Blue 100％/White
100％
6
000 015
No function
STROBE
016 215
Normal strobe
216 255
Random slow strobe
7
0 10
NO FUNCTION
11 50
AUTO1
Auto-program effect running
51 100
AUTO2
Auto-program effect running
101 150
AUTO3
Auto-program effect running
151 200
AUTO4
Auto-program effect running
201 255
AUTO5
Auto-program effect running
8
0 255
AUTO SPEED
9
0 09
NO FUNCTION
Fading speed
10 34
Linear dimming speed (dIM=OFF)
35 59
Non-linear dimming speed 1(dIM=1)
60 84
Non-linear dimming speed 2(dIM=2)
85 109
Non-linear dimming speed 3(dIM=3)
110 134
Non-linear dimming speed 4(dIM=4)
135 159
Non-linear dimming speed 5(dIM=5)
160 184
Non-linear dimming speed 6(dIM=6)
185 209
Non-linear dimming speed 7(dIM=7)
210 255
Non-linear dimming speed 8(dIM=8)

- 11 -
5Maintenance
5.1 Product Maintenance
To prolong the life of the product, it is very important to do maintenance work. The environment is hash
outdoors, or if the product is idle for a long time, damp, smoke or particularly dirty surroundings can
cause greater accumulation of dirt on its LED lens cover, fan vents and housing. So it should be cleaned
to maintain an optimum light output and at the same time to prevent it from corrupted by acid gas.
Cleaning frequency depends on the environment in which the fixture operates. Soft cloth and typical
glass cleaning products should be used for cleaning. It is recommended to clean product at least one
every 20 days.
Friendly notice: Please do not use any organic solvent, e.g. alcohol to
clean housing of the apparatus, lest cause damage.
5.2 Trouble Shooting
Remark: This product warranty for one year. We provide pay-needed maintenance service after the
warranty. But because of natural and man-made disasters or improper operation caused damage not
under warranty range!
SUPER-CAN INDUSTRY GROWING GROUP CO.,LTD.
MADE IN CHINA
Problems
Action
The product doesn't
switch on
Power connection is not correct--Re-connect it.
Power supply is damaged or abnormal. Call a qualified personnel to fix it.
Control section is damaged. Call a qualified personnel to fix it.
Connection of internal circuitry is not correct. Call a qualified personnel to fix it.
The product can turn
on,but LEDs do not emit
light and are out of control
DMX address is wrongly setting up. Resetting it according to instruction book.
DMX Signal wrongly connected. Connect it correctly according to instruction book.
Control section is damaged. Call a qualified personnel to fix it.
The beam appears dim
The product is too hot. Take ventilation measures to make it cool.