Super Circuits MVL24KIT Parts list manual

1www.supercircuits.com MVL24KIT_SQ
1. Tighten the adjustment knob on the side
of the gimbal assembly, then screw the
gimbal assembly onto the mounting
bracket until it is tight.
2. Anchor the camera mounting bracket and
gimbal assembly onto a at surface at the
surveillance location. The hardware kit
provided is useful for securing the bracket
onto most surfaces.
3. Attach the rubber washer (included in the
hardware kit) onto the gimbal bolt.
4. Loosen the adjustment knob.
Rubber
washer Adjustment
knob
5. Screw the gimbal bolt into the threaded hole on the underside of the camera.
6. Aim the camera at your surveillance target, then tighten the adjustment knob.
7. Attach the antenna to the back of the camera assembly.
Power cord
Antenna
connector
PAIR button
(under cap)
8. Plug the camera power cord into the 12 VDC power adapter provided, then plug the power adapter
into a standard 120 VAC outlet. WARNING: Do not use the 5 VDC power adapter provided for the
RX module with the MVL24CM camera.
Step 2. Installation - RX module
1. Find a location for the RX module that is within 500’ of the camera. If obstructions (walls, etc.)
exist between the camera and RX module, the module must be positioned closer to the camera.
The RX module can be anchored to the mounting surface, if necessary. The hardware kit provided is
useful for securing the module onto most surfaces.
2. Attach the A/V cable provided to the RX
module A/V OUT connector, then plug the
yellow RCA jack into a video recorder or
monitoring system. (NOTE: This kit does not
support audio monitoring.)
3. Attach the RX module antenna to the antenna
connector on the back of the module.
4. Plug the RX module 5 VDC power adapter
into the DC5V connector on the RX module,
then into a standard 120 VAC outlet.
WARNING: Do not use the 12 VDC power
adapter provided for the MVL24CM camera
with the RX module.
DC5V
power
connector
A/V OUT
connector
PAIR
button
MVL24KIT Digital Camera/Receiver System
Setup and Usage Guide
The MVL24KIT 420 Line 2.4GHz Digital Wireless video IR camera kit is a reliable and exceptionally easy to
install monitoring solution for home or oce. It includes these features:
• 30’ IR Range
• 500’ line of sight (camera to receiver) range
• Weather-resistant IP55 housing
• Red LED deterrent light built-in
• Digital wireless frequency hopping technology
• 3 dB omnidirectional antenna
A local area can accommodate up to 4 camera - receiver systems concurrently.
The MVL24KIT is composed of three SKUs: MVL24CM Digital Wireless IR Camera, MVL24RX 2.4GHz Digital
Wireless Receiver, and CON-4 female RCA to male BNC Adapter. An optional hi-gain antenna is available
for the MVL24RX receiver to improve reception and extend the range of the system.
What’s in the box:
MVL24CM Digital Wireless IR Camera:
• Camera assembly
• 12 VDC power adapter
• Antenna (1)
• Mounting bracket and gimbal assembly
• Hardware kit
MVL24RX 2.4GHz Digital Wireless Receiver:
• Receiver (RX) module
• 5 VDC power adapter
• Antenna (1)
• A/V cable
• Hardware kit
Step 1. Installation - camera
The camera is installed onto a mounting bracket and gimbal assembly, then powered on.
Mounting Bracket
Gimbal Assembly
All manuals and user guides at all-guides.com
all-guides.com

2www.supercircuits.com © 2011 Supercircuits, Inc. All rights reserved.
Step 3. PAIRing the camera and RX module
To PAIR the camera and RX module is the process for establishing a communication link between them.
Eective PAIRing is achieved when video from the receiver module can be seen at the video monitoring
equipment.
Single camera - RX module system
PAIRing a single camera - RX module system occurs automatically when the camera and RX module are
powered on. The POWER LED on the camera and receiver module ash initially, then remain on constantly
when camera and RX module are PAIRed. If PAIRing is lost, it can be re-established by powering o, then
powering on one or both of the units.
POWER LED
NOTE: After powering o either unit, wait about 10 seconds before powering it on again.
Multiple camera - receiver systems
In a multiple camera - RX module systems, placed the RX modules at least 1 foot apart. PAIRing can be
performed by powering on each camera and RX module system one at a time and waiting until they
PAIR. If PAIRing is lost between one camera and RX module system, it can be re-established by powering
o, then powering on either the camera or RX module of the system, then allowing them to PAIR
automatically.
Manual PAIRing
If PAIRing was not achieved automatically (no video signal from the receiver module), it can be manually
initiated by pressing and holding the PAIR button on the camera and/or RX module for 5 seconds. The
POWER LED will ash for about 10 seconds, then remain on continuously when the units are PAIRed.
The PAIR button on the camera is located on the back of the unit beneath a rubber cap. On the RX module,
the PAIR button is located on the top of the unit.
Troubleshooting
Problem Possible Solutions
No video
• Check power and A/V cable connections.
• Verify that the camera and RX module are powered on.
• Verify that the recording/video monitoring equipment is functioning properly.
• Verify that the POWER LEDs are lit constantly. If the POWER LEDs are ashing,
use the procedure above to PAIR the units.
Interference in video
• Adjust the orientation of the camera and RX module antennas.
• Move the equipment away from devices that emit high radiation, such as
microwave ovens, wireless phones, etc.
Specications - system
Item Specication
Transmission channels 80 channels, auto selected
Video bit rate Up to 12 Mbps
ID codes Up to 4 M
Video resolution 720 x 480 @ 30 fps (NTSC)
Operational range 500 ft (line of sight)
Specications - camera
Item Specication
Operating frequency 2.4000GHz – 2.4835GHz
Transmit power 100mW (maximum)
Modulation 16 QAM / QPSK / BPSK
Antenna Omnidirectional
Power consumption 1.9 W
Voltage 12 VDC / 1A
Dimensions 5.12” x 2.76” x 2.28” (130mm x 70mm x 58mm)
Weight 21.87oz (620g)
Specications - RX module
Item Specication
Operating frequency 2.4000GHz – 2.4835GHz
Receiver sensitivity -80dBm minimum
Video output level 1 ±0.2 Vp-p @ 75 Ω
Audio output level 1 ± 0.2 Vp-p @ 600 Ω (stereo) (NOTE: the MVL24CM does not provide an audio signal.)
Antenna 3 dB, omnidirectional
Power consumption 1.9 W
Power supply 5V / 1A
Dimensions 2.99” x 2.876” x .94” (76mm x 73mm x 24mm)
Weight 2.89 oz (82g)
All manuals and user guides at all-guides.com