dallmeier RDF5000 Series User manual

camera series RDF5000(E)
INSTALLATION AND CONNECTION OF A DOMERA® IR LED STRIPE INCLUDING DOMERA® HOUSING COVER ALUMINIUM LED BLACK
© 2022 Dallmeier electronic V1.0.0 2022.11.17 1/7
▶ Remove the camera‘s housing cover
by turning and lifting it.
Preparing the camera
▶ Required for mounting:
1 x DOMERA® RDF5000(E)
1 x DOMERA® IR LED Stripe Retrot Kit
1 x Allen key (3)
1 x Tweezers
1 x Torx screwdriver (TX 8)
▶ Carefully remove the three rubber
covers of the screws with tweezers.
approx. 10°

camera series RDF5000(E)
INSTALLATION AND CONNECTION OF A DOMERA® IR LED STRIPE INCLUDING DOMERA® HOUSING COVER ALUMINIUM LED BLACK
© 2022 Dallmeier electronic V1.0.0 2022.11.17 2/7
▶ Then remove the cover ring including
the dome from the camera.
▶ Open the three screws of the cover
ring counterclockwise using an
Allen key.
▶ Carefully lift the rubber seal out of
the camera housing using tweezers.

camera series RDF5000(E)
INSTALLATION AND CONNECTION OF A DOMERA® IR LED STRIPE INCLUDING DOMERA® HOUSING COVER ALUMINIUM LED BLACK
© 2022 Dallmeier electronic V1.0.0 2022.11.17 3/7
▶ Insert the circuit board into the
corresponding slot and press it
carefully with light pressure.
▶ Insert the new seal into the slot
and press rmly until it rests evenly
on the surface.
▶ Insert the screws and tighten
them clockwise with an Allen key.

camera series RDF5000(E)
INSTALLATION AND CONNECTION OF A DOMERA® IR LED STRIPE INCLUDING DOMERA® HOUSING COVER ALUMINIUM LED BLACK
© 2022 Dallmeier electronic V1.0.0 2022.11.17 4/7
Installing the IR LED Stripe
▶ Place the IR LED stripe on the camera.
▶ Gently press on it until the plug
snaps into the socket.
▶ Insert the screw into the IR LED
Stripe and tighten it clockwise.
▶ Place the cover ring with the dome
on the IR LED stripe of the camera.
Pay attention to the alignment of
the three bracket screws.

camera series RDF5000(E)
INSTALLATION AND CONNECTION OF A DOMERA® IR LED STRIPE INCLUDING DOMERA® HOUSING COVER ALUMINIUM LED BLACK
© 2022 Dallmeier electronic V1.0.0 2022.11.17 5/7
▶ Carefully remove the protective
foil with tweezers.
▶ Remove the protective foil from
all ve viewing windows.
▶ Then tighten the screws clockwise
using an Allen key.

camera series RDF5000(E)
INSTALLATION AND CONNECTION OF A DOMERA® IR LED STRIPE INCLUDING DOMERA® HOUSING COVER ALUMINIUM LED BLACK
© 2022 Dallmeier electronic V1.0.0 2022.11.17 6/7
▶ Use the tweezers to remove the two
red covers for the fastening screws.
▶ Reinsert the rubber covers over
the three screws.
Installing the aluminum ring
▶ Mount the safety strap on the
camera with the self-tapping screw
and on the housing cover with the
metric screw.

Dallmeier electronic GmbH & Co.KG | Bahnhofstr. 16, 93047 Regensburg, Germany | [phone] | dallmeier.com
All trademarks identified by ® are registered trademarks of Dallmeier electronic GmbH & Co.KG.
Third-party trademarks are named for information purposes only. Dallmeier electronic respects the intellectual property of third parties and always attempts to ensure the complete identification of third-party
trademarks and indication of the respective holder of rights. In case that protected rights are not indicated separately, this circumstance is no reason to assume that the respective trademark is unprotected.
Specifications subject to change without notice. Errors and misprints excepted. Pictures may dier from the actual product.
© 2022 Dallmeier electronic V1.0.0 2022.11.17 7/7
camera series RDF5000(E)
INSTALLATION AND CONNECTION OF A DOMERA® IR LED STRIPE INCLUDING DOMERA® HOUSING COVER ALUMINIUM LED BLACK
▶ Place the aluminum ring on the
camera. Pay attention to the
position of the two bracket screws.
▶ Tighten them clockwise with an
Allen key.
▶ The installation is completed.
The camera can now be mounted.