Superior Fireplaces LMF24GTA Owner's manual

Installation and Operation Instructions
Models
PFS
®
USC
Report No. 10-87
P/N 900464-01 Rev. B 01/2019
Superior®Vented Gas Log and Burner Set
MNF24ONE MNF24OPE MNF30ONE MNF30OPE
For use with log sets
LMF24GTA/B
LMF30GTA/B
LMF36GTA/B
LMF24MOA/B
LMF30MOA/B
LMF36MOA/B
WHEN USED AS INDOOR VENTED APPLIANCE
- Do not store or use gasoline or other flammable vapors and liquids in the vicinity of this or any other appli-
ance.
- WHAT TO DO IF YOU SMELL GAS
• Do not try to light any appliance.
• Do not touch any electrical switch; do not use any phone in your building.
• Leave the building immediately.
• Immediately call your gas supplier from a neighbor’s phone. Follow the gas supplier’s instructions.
• If you cannot reach your gas supplier, call the fire department.
- Installation and service must be performed by a qualified installer, service agency or the gas supplier.
WARNING:
FIRE OR EXPLOSION HAZARD
Failure to follow safety warnings exactly could result in serious injury, death, or property damage.
INSTALLER: Leave this manual with the appliance.
CONSUMER: Retain this manual for future reference.
WHEN USED AS AN OUTDOOR APPLIANCE
CARBON MONOXIDE WARNING
• This appliance can produce carbon
monoxide which has no odor.
• Using it in an enclosed space can
kill you.
• Never use this appliance in an en-
closed space such as a camper, tent,
car or home.
WARNING: For Outdoor Use Only.
DANGER
IF YOU SMELL GAS:
1. Shut off gas to appliance.
2. Extinguish any open flame.
3. If odor continues, keep away from the
appliance and immediately call your gas
supplier or fire department.
WARNING: No not store gasoline or other flammable vapors and liquids in the vicinity of this or any other
appliance. An LP-cylinder not connected for use shall not be stored in the vicinity of this or any other appliance.
WARNING: Improper installation, adjustment, alteration, service or maintenance can cause injury or
property damage. Read the installation, operating and maintenance instructions thoroughly before install-
ing or servicing this equipment.
DANGER
P900464-01

SuperiorFireplaces.us.com 900464-01B
2
SAFETY
than others. These include pregnant women, people with
heart or lung disease or anemia, those under the inuence
of alcohol and those at high altitudes.
Natural and Propane/LP gases are odorless. An odor-making
agent is added to these gases. The odor helps you detect a
gas leak. However, the odor added to the gas can fade. Gas
may be present even though no odor exists.
Make certain you read and understand all warnings. Keep
this manual for reference. It is your guide to safe and proper
operation of this replace.
WARNING: Any change to this appliance or its
controls can be dangerous.
Solid fuels shall not be burned in a replace where a
decorative appliance is installed.
Due to high temperatures, the appliance should be
located out of trafc and away from furniture and
draperies.
Do not place clothing or other ammable material on
or near the appliance. Never place any objects on the
appliance.
A p p lianc e ba s e as s e m b l y be c o m e s ve r y ho t wh e n r u n -
n i n g a p p l i a n c e . K e e p c h i l d r e n a n d a d u l t s a w a y f r o m h o t
surface to avoid burns or clothing ignition. Appliance
will remain hot for a time after shutdown. Allow surface
to cool before touching.
Carefully supervise young children when they are in the
room with appliance. When using the hand-held remote
accessory, keep selector switch in the OFF position to
prevent children from turning on burners with remote.
You must operate this appliance with the replace
screen and hood in place. Make sure replace screen
and hood are in place before running appliance. The
replace screen shall have openings for introduction
of combustion air.
Keep the appliance area clear and free from combus-
tible materials, gasoline and other ammable vapors
and liquids.
WARNING: Improper installation, adjustment, al-
teration, service or maintenance can cause injury or
property damage. Refer to this manual for correct in-
stallation and operational procedures. For assistance
or additional information consult a qualied installer,
service agency or the gas supplier.
WARNING: This appliance is for installation only
in a solid-fuel-burning masonry or UL127 factory-built
replace or in a listed outdoor replace. Do not install
this appliance in an unvented replace indoors.
WARNING: Fireplace must be operated only with
doors fully open.
This appliance may be installed in an aftermarket,*
permanently located, manufactured (mobile) home,
where not prohibited by local codes.
This appliance is only for use with the type of gas
indicated on the rating plate. This appliance is not
convertible for use with other gases.
* Aftermarket: Completion of sale, not for purpose of resale,
from the manufacturer
WARNING: This product can expose you to chemicals
including Carbon Black, which is known to the State of
California to cause cancer, and Carbon Monoxide, which
is known to the State of California to cause birth defects
or other reproductive harm. For more information go to
www.P65Warnings.ca.gov
IMPORTANT: Read this owner’s manual carefully and
completely before trying to assemble, operate or ser-
vice this appliance. Improper use of this appliance can
cause serious injury or death from burns, re, explo-
sion, electrical shock and carbon monoxide poisoning.
DANGER: Carbon monoxide poisoning may lead
to death!
Carbon Monoxide Poisoning: Early signs of carbon mon-
oxide poisoning resemble the u, with headaches, dizziness
or nausea. If you have these signs, the replace may not be
working properly. Get fresh air at once! Have replace ser-
viced. Some people are more affected by carbon monoxide
TABLE OF CONTENTS
Safety ..................................................................................2
Product Identication...........................................................3
Local Codes.........................................................................4
Unpacking............................................................................4
Product Features.................................................................4
Installation ...........................................................................4
Operation...........................................................................14
Inspecting Burners.............................................................15
Cleaning and Maintenance................................................16
Specications ....................................................................16
Wiring Diagram..................................................................17
Troubleshooting.................................................................18
Accessories .......................................................................21
Parts ..................................................................................22
Replacement Parts............................................................26
Service Hints .....................................................................26
Technical Service...............................................................26
Warranty ............................................................................27

SuperiorFireplaces.us.com
900464-01B 3
SAFETY
Continued
1. This appliance is only for use with the type of gas indicated
on the rating plate. This appliance is not convertible for use
with other gases.
2. Do not place propane/LP supply tank(s) inside any struc-
ture. Locate propane/LP supply tank(s) outdoors (propane/
LP units only).
3. If you smell gas
•shut off gas supply
•do not try to light any appliance
•do not touch any electrical switch; do not use any phone
in your building
•immediately call your gas supplier from a neighbor’s
phone. Follow the gas supplier’s instructions
• if you cannot reach your gas supplier, call the re depart-
ment
4. This appliance shall not be installed in a bedroom or bath-
room, unless installed as a vented appliance. See Installing
Damper Clamp Accessory for Vented Operation, Page 6.
This gas log set may not be installed as a vented appli-
ance in a bedroom or bathroom in the Commonwealth of
Massachusetts.
5. Before installing in a solid fuel-burning replace, the chim-
ney ue and rebox must be cleaned of soot, creosote,
ashes and loose paint by a qualied chimney cleaner.
Creosote will ignite if highly heated. A dirty chimney ue
may create and distribute soot within the house. Inspect
chimney ue for damage. If damaged, repair ue and
rebox before operating appliance.
6. If replace has glass doors, never operate this appliance
with glass doors closed. If you operate appliance with doors
closed, heat buildup inside replace will cause glass to
burst. Make sure there are no obstructions across open-
ings of replace.
7. To prevent the creation of soot, follow the instructions in
Cleaning and Maintenance, Page 16.
8. Before using furniture polish, wax, carpet cleaner or similar
products, turn appliance off. If heated, the vapors from these
products may create a white powder residue within burner
box or on adjacent walls and furniture.
9. Do not use this appliance as a wood burning appliance.
Use only the logs provided with the appliance. Do not burn
solid fuels in this appliance.
10.Do not run appliance
• where ammable liquids or vapors are used or stored
•under dusty conditions
11.Do not use this appliance to cook food or burn paper or
other objects.
12.Do not use this appliance if any part has been exposed to
or under water. Immediately call a qualied service tech-
nician to inspect the room appliance and to replace any
part of the control system and any gas control which has
been under water.
13.Do not operate appliance if any log is broken.
14.Turn appliance off and let cool before servicing, installing
or repairing. Only a qualied service person should install,
service or repair appliance.
PRODUCT IDENTIFICATION
Figure 1 - Product Identication
15.This appliances must not be connected to any external
electrical source.
16.Operating appliance above elevations of 4,500 feet may
cause pilot outage.
17.To prevent performance problems, do not use propane/
LP fuel tank of less than 100 lb. capacity (propane/LP
units only).
18.Provide adequate clearances around air openings.
19.Do not operate replace if any log is broken.
If used with MFEB accessory ember burner, this appli-
ance shall only be installed in a wood burning replace.
WARNING: This appliance shall not be installed in a
room or space unless the required volume of indoor
combustion air is proved by the method described in
the National Fuel Gas Code, ANSI Z223.1/NFPA 54, the
International Fuel Gas Code.
Any part removed for servicing the appliance must be
replaced prior to operating the appliance.
When installing as a vented appliance in a manufactured
home or mobile home, the installation must conform
with the Manufactured Home Construction and Safety
Standard, Title 24 CFR, Part 3280 or when standard is
not applicable, with Manufacture Home Installations
Standard, ANSI/NCSBCS A225.1/NFPZ 501A.

SuperiorFireplaces.us.com 900464-01B
4
LOCAL CODES
Install and use appliance with care. Follow all local codes.
In the absence of local codes, use the latest edition of The
National Fuel Gas Code, ANSI Z223.1/NFPA 54*.
*Available from:
American National Standards Institute, Inc.
25 West 43rd Street, 4th oor
New York, NY 10036
National Fire Protection Association, Inc.
1 Batterymarch Park
Quincy, MA 02169-7471
State of Massachusetts: The installation must be made
by a licensed plumber or gas tter in the Commonwealth of
Massachusetts.
Sellers of unvented propane or natural gas-red supplemen-
tal room appliances shall provide to each purchaser a copy
of 527 CMR 30 upon sale of the unit.
Vent-free gas products are prohibited for bedroom and bath-
room installation in the Commonwealth of Massachusetts.
UNPACKING
CAUTION: Do not remove the data plates
from the grate assembly. The data plates con-
tain important warranty and safety information.
1. Remove logs and appliance base assembly from carton(s).
2. Remove all protective packaging applied to logs and ap-
pliance for shipment.
3. Check appliance for any shipping damage. If appliance is
damaged, promptly inform dealer where you purchased the
appliance.
PRODUCT FEATURES
OPERATION
This appliance is dual listed as a vented decorative gas
appliance to ANSI Z21.60 for use indoors in wood burning
replaces and as an outdoor decorative gas appliance to
ANSI Z21.97. When operated as an outdoor decorative gas
appliance, it must be installed outdoors in a site built wood
burning replace or a UL 127 listed wood burning replace
designed for outdoor use or in an unvented outdoor replace.
If optional accessory MFEB is used, the replace in which
the appliance is installed must have a working vent/ue as
described within these instructions.
ELECTRONIC IGNITION SYSTEM
This appliance has an electronic igniter to light appliance
fuel supply.
INSTALLATION
WARNING: A qualied service person must
install appliance. Follow all local codes.
NOTICE: State or local codes may only allow
operation of this appliance in a vented con-
guration. Check your state or local codes.
WARNING: Make sure the selector switch is
in the OFF position before installing appliance.
WARNING: Never install the appliance
• in a recreational vehicle
• where curtains, furniture, clothing or other am-
mable objects are less than 36" from front, 42"
from top of appliance; for side clearances see
Figure 2, Page 5
• in high trafc areas
• in windy or drafty areas
OUTDOOR ENCLOSURE REQUIREMENTS
This appliance is considered to be installed outdoors if in-
stalled with shelter no more inclusive than:
1. With walls on all sides, but with no overhead cover;
2. Within a partial enclosure which includes an overhead cover
and no more than two side walls. These side walls may be
parallel, as in a breezeway or at right angles to each side; or
3. Within a partial enclosure which includes an overhead cover
and three side walls; as long as 30% or more of the horizontal
periphery of the enclosure is permanently open.
This appliance must be installed in an approved replace.
When installed indoors or either indoors or outdoors with
optional ember burner MFEB, the appliance must be installed
in a wood burning replace with the ue damper in the open
position. This appliance may only be installed in a replace
with no ue when installed in an approved outdoor replace.
When installed in an outdoor replace with no ue, optional
ember burner MFEB may not be used.
CHECK GAS TYPE
Use the correct type of gas (natural or propane/LP). If your gas
supply is not the correct gas type, do not install appliance. Call
dealer where you bought appliance for proper type appliance.
WARNING: This appliance is equipped for
either natural gas or propane/LP gas but not
both. Gas type is indicated on the rating plate.
Field conversion is not permitted.
INSTALLATION AND CLEARANCES
WARNING:Maintaintheminimumclearances.
If you can, provide greater clearances from oor,
ceiling and adjoining wall.
WARNING: DO NOT INSTALL IN SLEEPING
ROOM OF MOBILE HOMES.

SuperiorFireplaces.us.com
900464-01B 5
Carefully follow the instructions below. This will ensure safe
installation into a masonry, UL127-listed manufactured re-
place or listed outdoor rebox.
Minimum Clearances For Side Combustible Material, Side
Wall and Ceiling
A. Clearances from the side of the replace cabinet to any com-
bustible material and wall should follow diagram in Figure 2.
Example:The face of a mantel, bookshelf, etc. is made of
combustible material and protrudes 3-1/2" from the wall.
This combustible material must be 4" from the side of the
replace cabinet (see Figure 2).
NOTE: When installing your gas logs into a manufactured
rebox, follow rebox manufacturer’s instructions for mini-
mum clearances to combustible materials.
B. Clearances from the top of the replace opening to the ceil-
ing should not be less than 42".
INSTALLATION
Continued
Figure 2 - Minimum Clearance for Combustible to Wall
*Minimum 16" from Side Wall
* When you add the optional MAGNIFLAME EMBER BURNER KIT
MFEB the depth dimension increases by 3.50''
*
Example
Minimum Noncombustible Material Clearances
If Not Using Mantel
NOTE: If using a mantel proceed to If Using Mantel. If not
using a mantel, follow these instructions.
You must have noncombustible material(s) above the replace
opening. Noncombustible materials (such as slate, marble, tile,
etc.) must be at least 1/2" thick. With sheet metal, you must
have noncombustible material behind it. Noncombustible
material must extend at least 8" up (for all models). If noncom-
bustible material is less than 12", you must install the replace
hood accessory. See Figure 3 for minimum clearances.
If Using Mantel
You must have noncombustible material(s) above the replace
opening. Noncombustible materials (such as slate, marble,
tile, etc.) must be at least 1/2" thick. With sheet metal, you
must have noncombustible material behind it. Noncombus-
tible material must extend at least 8" up (for all models). If
noncombustible material is less than 12", you must install the
replace hood accessory. Even if noncombustible material is
more than 12", you may need the hood accessory to deect
heat away from your mantel shelf. See Figure 3 and Figures
4 and 5, Page 6, for minimum clearances.
IMPORTANT:If you cannot meet these minimum clearances,
you must operate appliance with chimney ue damper open.
Go to Installing Damper Clamp Accessory for Vented Opera-
tion, Page 6.
Noncombustible
Material Distance
(A)
Requirements for Safe Installation
1 2" or more Noncombustible material OK.
Between 8" and 12" Install replace hood accessory
(GA6050 - see Accessories, Page 21).
Less than 8" Noncombustible material must be ex-
tended to at least 8". See Between 8"
and 12", above. If you cannot extend
material, you must operate appliance
with ue damper open.
MINIMUM FIREPLACE CLEARANCE TO COMBUSTIBLE
MATERIALS
Side Wall 16", Ceiling 42"
Floor 5", Front: 36"
LOG SIZING REQUIREMENTS
Log
Size
Minimum Firebox Size
Height Depth Front
Width
Rear*
Width
LMF24GTA/B
LMF24MOA/B 29" 15.5" 32.5" 22.75"
LMF30GTA/B
LMF30MOA/B 29" 15.5" 39" 26.75"
LMF36GTA/B
LMF36MOA/B 29'' 20'' 47'' 33''
Heat Resistant
Material
(A)
Figure 3 - Heat Resistant Material (Slate, Marble, Tile,
etc.) Above Fireplace

SuperiorFireplaces.us.com 900464-01B
6
NOTICE: Surface temperatures of adjacent
walls and mantels become hot during opera-
tion. Walls and mantels above the rebox may
become hot to the touch. If installed properly,
these temperatures meet the requirement of the
national product standard. Follow all minimum
clearances shown in this manual.
NOTICE: If your installation does not meet the
minimum clearances shown, you must do one
of the following:
• operate the logs only with the ue damper
open
• raise the mantel to an acceptable height
• remove the mantel
FLOOR CLEARANCES
A. If installing appliance on the oor level, you must maintain
the minimum distance of 14" to combustibles (see Fig-
ure 6).
B. If combustible materials are less than 14" to the replace,
you must install appliance at least 5" above the combustible
ooring (see Figure 7).
Figure 4 - Minimum Mantel Clearances Without Using Hood
Figure 5 - Minimum Mantel Clearances When Using Hood
Minimum Non-
Combustible
Material
Minimum Non-
Combustible
Material Height
Distances to
Underside of
Mantel
Top of Fireplace
Opening
Underside of
Mantel Shelf
12"
(A)
18" 20" 22" 24"
All minimum
distances are
in inches
2
1/2
"
6"
8"
10"
Mantel Shelf
Minimum
Noncombustible
Material 8"
Min.
12" 15" 18" 20"
2 1/2"
6"
8"
10"
12"
Distances to
Underside of
Mantel
Hood (GA6050
or GA6053)
Top of
Fireplace
Opening
Underside
of Mantel
Shelf
Mantel Shelf
INSTALLATION
Continued
Determining Minimum Mantel Clearance When Using a
Hood
If minimum clearances in Figure 4, are not met, you must have
a hood. When using a hood there are still certain minimum
mantel clearances required. Follow minimum clearances
shown in Figure 5, when using hood.
INSTALLING DAMPER CLAMP ACCESSORY FOR
VENTED OPERATION
NOTE: When used as a vented indoor appliance, appliance
must be installed only in a solid-fuel-burning replace with
a working ue and constructed of noncombustible material.
MANTEL CLEARANCES
In addition to meeting noncombustible material clearances,
you must also meet required clearances between replace
opening and mantel shelf. If you do not meet the clearances
listed below, you will need a hood.
Determining Minimum Mantel Clearance
If you meet minimum clearance between mantel shelf and top
of replace opening, a hood is not required (see Figure 4,
Page 6).
14"
Min.
Combustible
Material
Noncombustible Material
Figure 6 - Minimum Fireplace Clearances If Installed at
Floor Level
Hearth
5"
Min.
Combustible
Material
Figure 7 - Minimum Fireplace Clearances Above
Combustible Flooring
Minimum clearance requirements include any projections such as shelves, window
sills, mantels, etc. above the appliance.

SuperiorFireplaces.us.com
900464-01B 7
INSTALLATION
Continued
INSTALLING APPLIANCE BASE ASSEMBLY
Area of Various Standard Round Flues
Diameter Area
5" 20 sq. inches
6" 29 sq. inches
7" 39 sq. inches
8" 51 sq. inches
Chimney Height Minimum Permanent Flue Opening
6' to 15' 39 sq. inches
15' to 30' 29 sq. inches
Figure 8 - Attaching Damper Clamp
Damper
Damper
Clamp
Damper
Damper
Clamp
Damper
Manufactured Fireplace
Masonry Fireplace
INSTALLING APPLIANCE BASE ASSEMBLY
WARNING: You must secure this appliance
to replace oor. If not, appliance will move
when you adjust controls. Moving appliance
may cause a gas leak.
WARNING: If installing in a sunken replace,
special care is needed. You must raise the re-
place oor to allow access to appliance control
panel. This will ensure adequate air ow and
guard against sooting and controls being dam-
aged. Raise replace oor with noncombustible
material. Make sure material is secure.
Figure 9 - Connecting Incoming Gas Line to Flex Gas Line
NOTE:
1) Wire connections not shown for clarity
2) * 1/8" NPT Plugged Tapping
MAIN
IN
OUT
PILOTADJ
PILOT
Pilot Adjustment
Inlet Pressure Tap
Outlet Pressure Tap
Gas Shutoff
Valve
Flexible Gas Line
Do NOT Kink
1/2" NPT Incoming
Gas Line
Set Screw
Installation Items Needed
• hardware package (provided with appliance)
• approved exible gas hose and ttings provided (if allowed
by local codes)
• sealant (resistant to propane/LP gas, not provided)
• electric drill with 3/16” masonry drill bit
1. Apply pipe joint sealant lightly to male threads of the 1/2
NPT side of gas tting elbow (provided) and connect to inlet
side of gas control. Remove gas tting from exible gas
hose (provided) before connecting to elbow (see Figure
9).
2. Position appliance base assembly in replace.
3. Mark screw locations through holes in front panel of base
(see Figure 10, Page 8). If installing in a brick-bottom
replace, mark screw locations in mortar joint of bricks.
4. Remove appliance base from replace.
5. Drill holes at marked locations using 3/16" drill bit.
6. Attach base, through holes in back side panels of base, to
replace oor using masonry screws provided in hardware
package (see Figure 10, Page 8).
7. Connect to gas supply. See Connecting To Gas Supply,
Page 8.
For Massachusetts Residents Only: Installation of this gas
log set as a vented indoor appliance in the Commonwealth of
Massachusetts requires the damper be permanently removed
or welded in the fully open position.
You must install the damper clamp accessory (to order, see
Accessories, Page 21). This will ensure vented operation
(see Figure 8). The damper clamp will keep damper open.
Installation instructions are included with clamp accessory.
See chart below for minimum permanent ue opening you
must provide. Attach damper clamp so the minimum perma-
nent ue opening will be maintained at all times.

SuperiorFireplaces.us.com 900464-01B
8
optional equipment shutoff valve from your dealer.
For propane/LP units, the installer must supply an external
regulator. The external regulator will reduce incoming gas
pressure. You must reduce incoming gas pressure to between
11" and 14" of water. If you do not reduce incoming gas pres-
sure, appliance regulator damage could occur. Install external
regulator with the vent pointing down as shown in Figure 11.
Pointing the vent down protects it from freezing rain or sleet.
CAUTION: Use only new, black iron or
steel pipe. Internally-tinned copper tubing
may be used in certain areas. Check your
local codes. Use pipe of 1/2" diameter or
greater to allow proper gas volume to appli-
ance. If pipe is too small, undue loss of volume
will occur.
Installation must include an equipment shutoff valve, union
and plugged 1/8" NPT tap. Locate NPT tap within reach for
test gauge hook up. NPT tap must be upstream from appli-
ance (see Figure 12, Page 9).
IMPORTANT:Install equipment shutoff valve in an acces-
sible location. The equipment shutoff valve is for turning on
or shutting off the gas to the appliance.
Check your building codes for any special requirements for
locating equipment shutoff valve to appliances.
Apply pipe joint sealant lightly to male NPT threads. This will
prevent excess sealant from going into pipe. Excess sealant
in pipe could result in clogged appliance valves.
WARNING: Use pipe joint sealant that is
resistant to liquid petroleum (LP) gas.
Figure 11 - External Regulator With Vent Pointing Down
Propane/LP
Supply Tank External
Regulator
with Vent
Pointing
Down
INSTALLATION
Continued
Figure 10 - Attaching Base to Fireplace Floor
(Model Shown May Vary from Actual Model)
Masonry Screw
CONNECTING TO GAS SUPPLY
WARNING: This appliance requires a 1/2"
NPT (National Pipe Thread) inlet connection
to the pressure regulator.
WARNING: A qualied service person must
connect appliance to gas supply. Follow all
local codes.
CAUTION: Never connect propane/LP ap-
pliance directly to the propane/LP supply.
This appliance requires an external regulator
(not supplied). Install the external regulator
between the appliance and propane/LP supply.
WARNING: Never connect natural gas ap-
pliance to private (non-utility) gas wells. This
gas is commonly known as wellhead gas.
Installation Items Needed
Before installing appliance, make sure you have the items
listed below.
• external regulator (supplied by installer)
• piping (check local codes)
• sealant (resistant to propane/LP gas)
• equipment shutoff valve *
• test gauge connection *
• sediment trap
• tee joint
• pipe wrench
• approved exible gas line with gas connector (if allowed by
local codes) (not provided)
* An equipment shutoff valve with 1/8" NPT tap is an ac-
ceptable alternative to test gauge connection. Purchase the

SuperiorFireplaces.us.com
900464-01B 9
INSTALLATION
Continued
We recommend that you install a sediment trap in supply
line as shown in Figure 12. Locate sediment trap where it is
within reach for cleaning. Install in piping system between fuel
supply and appliance. Locate sediment trap where trapped
matter is not likely to freeze. A sediment trap traps moisture
and contaminants. This keeps them from going into appliance
controls. If sediment trap is not installed or is installed wrong,
appliance may not run properly.
CAUTION: Avoid damage to gas control.
Hold gas control with wrench when connect-
ing it to gas piping and/or ttings.
CHECKING GAS CONNECTIONS
WARNING: Test all gas piping and connec-
tions, internal and external to unit, for leaks
after installing or servicing. Correct all leaks
at once.
WARNING: Never use an open ame to
check for a leak. Apply a noncorrosive leak
detection uid to all joints. Bubbles forming
show a leak. Correct all leaks at once.
CAUTION: Make sure external regulator has
been installed between propane/LP supply and
appliance. See guidelines under Connecting
to Gas Supply, Page 8.
PRESSURE TESTING GAS SUPPLY PIPING SYSTEM
Test Pressures In Excess Of 1/2 PSIG (3.5 kPa)
1. Disconnect appliance with its appliance main gas valve
(control valve) and equipment shutoff valve from gas supply
piping system. Pressures in excess of 1/2 psig will damage
appliance regulator.
* Purchase the optional equipment shutoff valve from your
dealer.
**Minimum inlet pressure for purpose of input adjustment.
Figure 12 - Gas Connection
Pipe Cap Tee
Nipple Joint
Gas Control
3" Minimum
Sediment Trap
Equipment Shutoff Valve
With 1/8" NPT Tap*
Approved Flexible
Gas Hose (if allowed
by local codes)
PROPANE/LP
From External
Regulator
(11" W.C.**
to 14" W.C.
Pressure)
NATURAL
From Gas
Meter
(5" W.C.**
to 10.5"
W.C.
Pressure)
2. Cap off open end of gas pipe where equipment shutoff
valve was connected.
3. Pressurize supply piping system by either opening pro-
pane/LP supply tank valve for propane/LP gas or opening
main gas valve located on or near gas meter for natural
gas or using compressed air.
4. Check all joints of gas supply piping system. Apply noncor-
rosive leak detection uid to all joints. Bubbles forming show
a leak.
5. Correct all leaks at once.
6. Reconnect appliance and equipment shutoff valve to gas
supply. Check reconnected ttings for leaks.
Test Pressures Equal To or Less Than 1/2 PSIG (3.5 kPa)
1. Close equipment shutoff valve (see Figure 13).
2. Pressurize supply piping system by either opening pro-
pane/LP supply tank valve for propane/LP gas or opening
main gas valve located on or near gas meter for natural
gas or using compressed air.
3. Check all joints from gas meter to equipment shutoff valve
for natural gas or propane/LP supply to equipment shutoff
valve for propane/LP (see Figure 14 or Figure 15, Page
10). Apply noncorrosive leak detection uid to all joints.
Bubbles forming show a leak.
4. Correct all leaks at once.
Figure 13 - Equipment Shutoff Valve
Open
Closed
Equipment
Shutoff
Valve
Figure 14- Checking Gas Joints (Propane/LP Only)
Control Valve
Location
Propane/LP
Supply Tank Equipment
Shutoff Valve

SuperiorFireplaces.us.com 900464-01B
10
CONTROL AND BATTERY PACK
Installing Batteries in Battery pack
1. Remove access cover on battery pack.
2. Install 4 AA batteries, included, into battery pack following
positive and negative directions.
3. Replace access cover on battery pack.
4. Place battery pack next control valve away from the burner.
Installing Batteries in Handheld Remote Control
1. Remove battery cover on back of remote control.
2. Install supplied A23/12V battery following positive and
negative directions.
3. Replace battery cover onto remote control.
Gas Meter
Figure 15 - Checking Gas Joints (Natural Gas Only)
Control Valve
Location
Equipment Shutoff Valve
INSTALLATION
Continued
PRESSURE TESTING APPLIANCE GAS
CONNECTIONS
1. Open equipment shutoff valve (see Figure 13, Page 9).
2. Open main gas valve located on or near gas meter for
natural gas or open propane/LP supply tank valve.
3. Make sure control knob of appliance is in the OFF position.
4. Check all joints from gas meter to equipment shutoff valve
for natural gas or propane/LP supply to equipment shutoff
valve for propane/LP (see Figure 14, Page 9 or Figure
15, Page 10). Apply noncorrosive leak detection uid to all
joints. Bubbles forming show a leak.
5. Correct all leaks at once.
6. Light appliance (see Operation, Page 14). Check all other
internal joints for leaks.
7. Turn off appliance (see To Turn Off Gas to Appliance, Page 14).
INSTALLING BATTERIES IN HAND HELD REMOTE
INSTALLING LOGS AND VOLCANIC STONE
WARNING: Failure to position the parts in
accordance with these diagrams or failure to
use only parts specically approved with this
appliance may result in property damage or
personal injury.
CAUTION: After installation and periodically
thereafter, check to ensure that no ame comes
in contact with any log. With appliance set to
Hi, check to see if ames contact any log. If
so, reposition logs according to log installation
instructions in this manual. Flames contacting
logs will create soot.
LOG PLACEMENT
It is very important to install these logs exactly as instructed.
Do not modify logs. Only use logs supplied with appliance.
NOTE: Each log includes an identifying number cast in the
log. Look at each log when placing them on the burner system
to be certain it is correct.
1. Find the right front log (LMF24GTA/B or LMF24MOA/B
models: D-061, LMF30GTA/B or LMF30MOA/B models:
D-019, LMF36GTA/B or LMF36MOA/B models: D-027).
See Figures 16, 16A, 16B, and 16C for reference. The log
has a rectangular shape on the bottom that ts against the
lip on the black metal base, the square grate, and the round
tube burner. Slide the log in place as shown in gures.
Figure 16 - Installing Right Front Log
Burner
Tube
Grate Finger
Right Front Log
(D-061, D-019 or D027)
MF SERIES BURNER SYSTEM
LOG COMPATIBILITY CHART
Burner System Model Refractory Concrete Logs For Use With This Burner
System
MNF24ONE
MNF24OPE
LMF24GTA/B
LMF30GTA/B
LMF24MOA/B
LMF30MOA/B
MNF30ONE
MNF30OPE
LMF36GTA/B
LMF36MOA/B

SuperiorFireplaces.us.com
900464-01B 11
INSTALLATION
Continued
Figure 16A - Installing Right Front Log, Top View
Round Tube
Burner
Grate Finger
Figure 17 - Installing Back Left Log
Figure 16B - Installing Right Front Log, Top View
Figure 16C - Installing Right Front Log, Side View
Burner Tube Square Grate
2. Find the back left log (LMF24GTA/B or LMF24MOA/B mod-
els: D-060, LMF30GTA/B or LMF30MOA/B models: D-018,
LMF36GTA/B or LMF36MOA/B models: D-026). See Fig-
ures 17, 17A, and 17B. Figure 17A shows how the log must
t against the end of the burner. Figure 17B shows how the
notch in log ts against the vertical portion of the burner tube.
Place this log on the base assembly by inserting it from the
left side as shown in Figure 17. You will need to twist the
log slightly to get it to t against the burners properly. It will
rest even with the back edge of the pan.
Back Left Log (D-060,
D-018 or D026) Flat Part of Log
Log Notch
Burner Tube
Figure 17A - Installing Back Left Log
Figure 17B - Installing Back Left Log (D-018) Rear View
Burner Tube
Log Notch
Vertical Portion of Burner Tube

SuperiorFireplaces.us.com 900464-01B
12
INSTALLATION
Continued
Figure 18 - Installing Front Left Log
4. Find the charred log (D-020). See Figures 19, 19A, and
19B. The log has a slot in the bottom that ts over the
square grate and rests against the burner tube as shown in
Figure 19. Place this log on the base as shown in gures.
3. Find the front left log (LMF24GTA/B or LMF24MOA/B mod-
els: D-059, LMF30GTA/B or LMF30MOA/B models: D-017,
LMF36GTA/B or LMF36MOA/B models: D-025). See Figures
18, 18A, and 18B. The log has a rectangular stand off on
the bottom that ts against the lip on the black metal base as
shown in Figure 18A. The bottom of this log has a slot that
ts over the second bar on the grate as shown in Figure 18B.
Place the log on the base assembly as shown in gures.
Figure 18A - Installing Front Left Log Side View
Figure 18B - Installing Front Left Log
Charred Log
Log Notch
Right Front Log
Figure 19 - Installing Charred Log
Grate Finger Log Slot
Front Left Log (D-059,
D-017 or D-025)
Grate Fingers
Figure 19A - Installing Charred Log Top View
Figure 19B - Installing Charred Log Top Side View
Square Grate Log Notch
D020

SuperiorFireplaces.us.com
900464-01B 13
INSTALLATION
Continued
5. Find the middle split log (LMF24GTA/B or LMF24MOA/B
models: D-063, LMF30GTA/B or LMF30MOA/B models:
D-021, LMF36GTA/B or LMF36MOA/B models: D-028).
See Figures 20 and 20A. The split side of the log faces
forward. The log has a notch that ts around the burner
tube on the right side. The left side of the burner tube ts
into the notch on the back side of this log. The log is placed
properly when it sits parallel to the tube burner and the
square peg is pointing up. See gures for reference.
Figure 20 - Installing Middle Split Log (D-021)
Middle Split Log (D-063,
D-021 or D-028)
Square Peg
Figure 20A - Installing Middle Split Log Rear Top Side View
Figure 21 - Installing Right Split Crossover Log
Log Notch
Burner Tube
7. For GTA/GTB logs, nd the front top log (D-024). See
Figure 22. The left end of this log has a square hole that
ts over a square peg that is on the top of the middle split
log. The right end of this log rests behind the knot on the
top of the front right log.
6. Find the right split crossover log (D-022) The bottom of
the log has a rectangular stand off that ts in the slots on
the right side of the front right log and the middle split log.
Place this log as shown in Figure 21.
Right Split Crossover
Log (D-022)
Right Front Log
Square Peg
Figure 22 - Installing Large Middle Log
Front Top Log
(D-024) Rectangular
Peg
Right Split
Crossover
Log (D-022)
Middle Split Log
8. Find the back top log (LMF24GTA/B or LMF24MOA/B
models: D-062, LMF30GTA/B or LMF30MOA/B models:
D-023, LMF36GTA/B or LMF36MOA/B models: D-029).
See Figures 23, and 23A. The left end of this log has a
round hole that ts over the round peg that is on the top of
the back left log. The right end of this log has a rectangular
hole that ts over the rectangular peg on the top of the
right crossover log.
VOLCANIC STONE PLACEMENT
Place Volcanic Stone around the base of the burner assembly
on the replace oor to simulate an ash bed. Do not place
Volcanic Stone or any other material on the burner.

SuperiorFireplaces.us.com 900464-01B
14
INSTALLATION
Continued
Figure 23 - Installing Back Top Log and Final Assembly
Figure 23A - Installing Back Top Log, Top View
Right Split
Crossover
Log (D-022)
Back Top Log (D-062,
D-023 or D-029)
OPERATION
FOR YOUR SAFETY
READ BEFORE LIGHTING
WARNING: If you do not follow these instruc-
tions exactly, a re or explosion may result
causing property damage, personal injury or
loss of life.
A. This appliance does not have a pilot, it is equipped
with an ignition device which automatically lights the
pilot. Do not light pilot by hand.
B. BEFORE LIGHTING smell all around the appliance area
for gas. Be sure to smell next to the oor because some
gas is heavier than air and will settle on the oor.
WHAT TO DO IF YOU SMELL GAS
•Do not try to light any appliance.
• Do not touch any electric switch; do not use any
phone in your building.
•Immediately call your gas supplier from a neighbor's
phone. Follow the gas supplier's instructions.
C. Do not use this appliance if any part has been under
water. Immediately call a qualied service technician
to inspect the appliance and to replace any part of the
control system and any gas control which has been
under water.
LIGHTING
INSTRUCTIONS
1. STOP! Read the safety information rst.
2. Do not attempt to light the burner by hand.
3. Turn equipment shutoff valve clockwise to the OFF
position (see Figure 25). Do not force.
4. Wait ve (5) minutes to clear out any gas. Then smell for
gas, including near the oor. If you smell gas, STOP! Fol-
low “B” in the safety information. If you don't smell gas, go
to the next step.
5. Turn equipment shutoff valve counterclockwise to the
ON position. Do not force.
6. Push remote control ''ON'' button.
7. Visually locate igniter. Igniter should begin to spark and
main burner should ignite once ame appears at pilot.
• If lighting appliance for the rst time each season, it may
take several attempts before supply gas can reach pilot
and main burners.
•If appliance will not stay lit after several attempts, follow
instructions under To Turn Off Gas To Appliance and call
your service technician or gas supplier.
TO TURN OFF GAS
TO APPLIANCE
1. Push remote control ''OFF'' button.
2. Turn equipment shutoff valve clockwise to OFF. Do
not force.
Figure 24 - Installing Small Left Hand And
Right Hand Logs
For MOA/B logs only, follow steps 9 and 10.
9. Install the small Left Top Log D080 as shown in Figure 24
by mating the rectangular peg and notch.
10. Install the small Right Top Log D081 as shown in Figure 24.
D-080
D-081
Front Top
Left
Front Top
Right

SuperiorFireplaces.us.com
900464-01B 15
OPERATION
Continued
Figure 25 - Turning Equipment Shutoff Valve to the OFF
Position
MAIN
IN
OUT
PILOTADJ
PILOT
Equipment
Shutoff Valve
Incoming
Gas Line
GAS CONTROL MODULE SYSTEM
REMOTE CONTROL FEATURE
The module has a built in remote control receiver that allows
the user to program the remote transmitter at any time during
or after the installation of the burner.
1. There is a switch located on the right side of the module
that reads REMOTE/OFF (Figure 26).
2. When the remote/off switch is in the OFF position, the
burner will operate from the rocker switch or wall switch
connected to the two BROWN wires on the module.
3. When the remote/off is in the REMOTE position the burner
will operate from the Remote Control Transmitter.
NOTE: The module must be programmed to the Remote
Control Transmitter.
• To program the module (make sure the system has
power), locate the learn button (Figure 27)on the module.
Locate the metal shield that is covering the module and
remove the screw on top. Use a small thin object like a
paper clip (not sharp points) to press and release the learn
button. There will be a beep sound from the module. Then
press any button on the remote transmitter. Once the
module's internal receiver accepts the transmitter code,
there will be a series of conrming beeps.
• The remote system is ready for use.
• Pushing and holding the LEARN button for 6 seconds
will result in clearing the transmitter security code from
the module's memory. The module will make three long
beeps in succession when it has been cleared.
Remote/Off Switch ADJ.
“S” Pilot Connection “I” Pilot Connection
AF-4000 MOD Module Rt Side
Figure 26 - Gas Module Right Side
AF-4000 MOD Module Lt Side
AUX Connection
Learn Button
Figure 27 - Gas Module Left Side
INSPECTING BURNERS
Check burner ame patterns often.
IGNITER ASSEMBLY
The igniter assembly is factory preset for proper ignition of
the burner. Alterations may have occurred during shipping
and handling. Call a qualied service person to readjust the
igniter assembly if necessary.
The igniter should be positioned as shown in Figure 28.
NOTE: Figure 28, shows the correct positioning of the igniter
and sensing rod.
If your igniter assembly does not meet these requirements:
• turn appliance off (see To Turn Off Gas to Appliance, Page
14).
• see Troubleshooting, Page 18
Figure 28 - Igniter Assembly
Igniter
Igniter
Sensing Rod
Burner
Tube
Figure 29 - Correct Burner Flame Pattern
BURNER FLAME PATTERN
Figure 29 shows correct burner ame pattern.
NOTICE: Do not mistake orange ames with
yellow tipping. Dirt or other ne particles are
burned by appliance, causing brief patches of
orange ame.
If burner ame pattern is incorrect, as shown in Figure 30,
Page 16.
• turn appliance off (see To Turn Off Gas to Appliance, Page
14)
• see Troubleshooting,Page 18
Yellow Flames with
Orange Streaks

SuperiorFireplaces.us.com 900464-01B
16
CLEANING AND MAINTENANCE
Continued
INSPECTING BURNERS
Continued
Figure 30 - Incorrect Burner Flame Pattern
CLEANING AND MAINTENANCE
WARNING: Turn off appliance and let cool
before cleaning.
CAUTION: You must keep control areas,
burners and circulating air passageways of ap-
pliance clean. Inspect these areas of appliance
before each use. Have appliance inspected
yearly by a qualied service person.
WARNING: Failure to keep the primary air
opening(s) of the burner(s) clean may result
in sooting and property damage.
BURNER INJECTOR HOLDER AIR INLET HOLE
The primary air inlet holes allow the proper amount of air to
mix with the gas. This provides a clean burning ame. Keep
these holes clear of dust, dirt, lint and pet hair. Clean these air
inlet holes prior to each heating season. Blocked air holes will
create soot. We recommend that you clean the unit every three
months during operation and have appliance inspected yearly
by a qualied service person.
We also recommend that you keep the burner tube clean and
free of dust and dirt. To clean these parts we recommend using
compressed air no greater than 30 PSI. Your local computer
store, hardware store or home center may carry compressed
air in a can. If using compressed air in a can, please follow
the directions on the can. If you don’t follow directions on the
can, you could damage the pilot assembly.
1. Shut off unit. Allow unit to cool for at least thirty minutes.
2. Inspect burner, and primary air inlet holes on injector holder
for dust and dirt (see Figure 31).
3. Blow air through the ports/slots and holes in the burner.
4. Check injector holder located at end of burner tube again.
Remove any large particles of dust, dirt, lint or pet hair with
a soft cloth or vacuum cleaner nozzle.
5. Blow air into the primary air holes on the injector holder.
6. In case any large clumps of dust have now been pushed
into the burner repeat steps 3 and 4. Additional cleaning
may be needed for proper operation based on use/lack of
use.
Figure 31 - Injector Holder On Outlet Burner Tube
Burner Tube
Injector
Holder
Primary Air
Inlet Holes
LOGS
• If you remove logs for cleaning, refer to Installing Logs and
Volcanic Stone, Page 10, to properly replace logs.
• Replace log(s) if broken or chipped (dime-sized or larger).
MAIN BURNER
Periodically inspect all burner ame holes with appliance running.
All slotted burner ame holes should be open with ame present.
All round burner ame holes should be open with a small blue
ame present. Some burner ame holes may become blocked
by debris or rust, with no ame present. If so, turn off appliance
and let cool. Remove blockage, blocked burner ame holes will
create soot.
WARNING: The injector holders (air shut-
ters) are not adjustable. Do not move injector
holders from their original positions.
At least once a year, the vent system for the
replace in which this appliance is installed
shall be inspected, cleaned, and repaired as
necessary by a qualied service person.
SPECIFICATIONS
MNF24ONE AND MNF30ONE
• Rating (Variable): 29,000/40,000 Btu/Hr
• Type Gas: Natural
• Ignition: Electronic
• Manifold Pressure: 3.4" W.C.
• Inlet Gas Pressure (in. of water):
Max - 10.5" W.C., Min* - 5" W.C.
*For purpose of input adjustment
MNF24OPE AND MNF30OPE
• Rating (Variable): 29,000/40,000 Btu/Hr
• Type Gas: Propane/LP
• Ignition: Electronic
• Manifold Pressure: 10.0" W.C.
• Inlet Gas Pressure (in. of water):
Max - 14" W.C., Min* - 11" W.C.
*For purpose of input adjustment
Dark Orange
Flames

SuperiorFireplaces.us.com
900464-01B 17
WIRING DIAGRAM
Orange
Orange
Orange
Red
Brown
Black
Solenoid
White
Brown
Brown
Green
Igniter
Pilot
I
S
AUX
AF-5000MOD
AF-4000
AF-4000B/P
Control Module
Black
Black
Optional DC Battery Back-up
Red
SWI
SWI
(GND)
Black
Red
HI/LO
Main
Black
These wires are not
used on this application

SuperiorFireplaces.us.com 900464-01B
18
TROUBLESHOOTING
WARNING: Turn off appliance and let cool before servicing. Only a qualied service person
should service and repair appliance.
NOTE: All troubleshooting items are listed in order of operation.
POSSIBLE CAUSE
1.Igniter electrode not connected to
igniter cable
2.Igniter cable pinched or wet
3.Broken igniter cable
4.Bad igniter
5.Igniter electrode positioned wrong
6.Igniter electrode broken
7.Battery not installed, battery
power low or battery not installed
correctly (electronic ignition mod-
els only)
1.Gas supply turned off or equip-
ment shutoff valve closed
2. Air in gas lines when installed
3.Depleted gas supply (propane/
LP only)
4.Control module not in REMOTE
position
5.Gas control valve pressure setting
is not correct
6.Inlet gas pressure is too low
7. Burner orice(s) clogged
8.Wire disconnected from gas con-
trol
9.Ground wire issue
REMEDY
1.Reconnect igniter cable
2.Free igniter cable if pinched by
any metal or tubing. Keep igniter
cable dry
3.Replace igniter
4.Replace igniter
5.Adjust igniter wires as shown in
Figure 28 on Page 15. Replace
igniter assembly if repositioning
does not correct the problem
6.Replace igniter
7.Install new alkaline battery in
remote control and battery pack.
Verify batteries are installed
correctly. (5.4 volts batteries re-
quired to operate valve system)
1.Turn on gas supply or open equip-
ment shutoff valve
2. Repeat igniting operation until air
is removed
3.Contact local propane/LP gas
company
4.Set control module to REMOTE
position
5. Contact qualied service person
to check pressure
6.Contact local natural or propane/
LP gas company
7.Clean burner (see Cleaning and
Maintenance, Page 16)or re-
place burner orice(s)
8. See Wiring Diagram, Page 17
9. Verify black ground wire from
module is secured under screw
adjacent to igniter
OBSERVED PROBLEM
When ''ON'' button on remote con-
trol is pressed, there is no spark at
igniter assembly
When ''ON'' button on remote control
is pressed, there is spark at igniter.
but no ignition

SuperiorFireplaces.us.com
900464-01B 19
POSSIBLE CAUSE
1.Manifold pressure is too low
2. Burner orice clogged
1. Burner orice is clogged or dam-
aged
2.Damaged burner
1.Residues from manufacturing
processes and logs curing
1.Air in gas line
2.Air passageways on appliance
blocked
3.Dirty or partially clogged burner
orice.
1.When heated, vapors from furni-
ture polish, wax, carpet cleaners,
etc. may turn into white powder
residue
1.Battery is not installed. Battery
power is low
1.Metal expanding while heating or
contracting while cooling
2.Igniter Assembly is out of position
3.Wind is disturbing the burner
ame and the igniter assembly is
relighting the burner
4. Wire connection loose or wire
broken
REMEDY
1.Contact local natural or propane/
LP gas company
2.Clean burner (see Cleaning and
Maintenance, Page 16)or replace
burner orice(s)
1.Clean burner (see Cleaning and
Maintenance, Page 16)or replace
burner orice
2.Replace damaged burner
1.Problem will stop after a few hours
of operation
1.Operate burners until air is re-
moved from line. Have gas line
checked by local natural or pro-
pane/LP gas company
2.Observe minimum installation
clearances (see Pages 4 through
6)
3.Clean burner (see Cleaning and
Maintenance, Page 16)or replace
burner orice(s)
1.Turn appliance off when using fur-
niture polish, wax, carpet cleaners
or similar products
1.Replace batteries in battery pack
and in hand-held remote
1.This is normal with most applianc-
es. If noise is excessive, contact
qualied service person
2.Check igniter position and adjust if
needed. See Figure 28, Page 15.
3.Should wind disturb the burner
ame, the igniter will automati-
cally spark to relight the burner.
This is normal when the appliance
is installed outdoors in windy con-
ditions.
4. Check wiring connections (see
wiring diagram, Page 17). Re-
place wire harness if necessary.
OBSERVED PROBLEM
Delayed ignition of burner
Burner backring during combustion
Slight smoke or odor during initial
operation
Appliance produces a whistling
noise when burners are lit
White powder residue forming within
burner box or on adjacent walls or
furniture
Remote does not function
Appliance produces a clicking/tick-
ing noise just after burners are lit
or shut off
TROUBLESHOOTING
Continued

SuperiorFireplaces.us.com 900464-01B
20
TROUBLESHOOTING
Continued
WARNING: If you smell gas
• Shut off gas supply.
• Do not try to light any appliance.
• Do not touch any electrical switch; do not use any phone in your building.
• Immediately call your gas supplier from a neighbor’s phone. Follow the gas supplier’s instruc-
tions.
• If you cannot reach your gas supplier, call the re department.
IMPORTANT: Operating appliance where impurities in air exist may create odors. Cleaning supplies, paint, paint remover,
cigarette smoke, cements and glues, new carpet or textiles, etc., create fumes. These fumes may mix with combustion air
and create odors. These odors will disappear over time.
POSSIBLE CAUSE
1. Appliance burning vapors from paint,
hair spray, glues, cleaners, chemicals,
new carpet, etc. (See IMPORTANT
statement above)
2.Low fuel supply (propane/LP only)
3.Gas leak. See Warning state-
ment at top of page
1.Low line pressure
1.Gas leak. See Warning state-
ment at top of page
2.Control valve or gas control de-
fective
1.The module's internal tempera-
ture is too high
1.The burner did not successfully
ignite
1.Gas leak. See Warning state-
ment at top of page
REMEDY
1.Open window to ventilate room.
Stop using odor causing products
while appliance is running
2.Refill supply tank (propane/LP
only)
3.Locate and correct all leaks (see
Checking Gas Connections,
Page 9)
1.Contact local natural or propane/
LP gas company
1.Locate and correct all leaks (see
Checking Gas Connections,
Page 9)
2.Replace control valve or gas con-
trol
1. Check to see the minimum re-
place size requirements are met,
Page 5
1.Press OFF then ON buttons to re-
attempt ignition. Refer to '' When
''on'' button on remote control is
pressed, there is spark at igniter
but no ignition'' on Page 18
1.Locate and correct all leaks (see
Checking Gas Connections,
Page 9)
OBSERVED PROBLEM
Appliance produces unwanted odors
Appliance shuts off in use
Gas odor even when control knob
is in OFF position
Module makes 4 beeps every 2
seconds
Module makes one beep every one
second
Gas odor during combustion