Superior Fireplaces WRE3036WS Owner's manual

PFS
®
USC
Installation and Operation Instructions
Superior® Residential and Outdoor Wood-
Burning Fireplace
Models
P127020-01
P/N 127020-01 Rev. E 03/2017
Report No. F10-078
WRE3036WS
WRE3036WH
SAVE THIS BOOK
This book is valuable. In addition to instructing you on how to install and maintain your appliance, it also
contains information that will enable you to obtain replacement parts or accessory items when needed. Keep
it with your other important papers.
INSTALLER: Leave this manual with the appliance.
CONSUMER: Retain this manual for future reference.
Installateur : Laissez cette notice avec l’appareil.
Consommateur : Conservez cette notice pour consultation ultérieure.
This wood burning fireplace complies with UL127
CAN/ULC-S610-M87 standard as a FACTORY
BUILT FIREPLACE.
Ce foyer au bois est conforme aux UL 127 CAN/ULC-
S610-M87 norme comme une USINE CONSTRUITE
CHEMINÉE.
This fireplace is approved for use as a wood burning fireplace or for use with a vented gas log approved to
ANSI Z21.60 or Z21.84 standards or for use with a vent-free gas log heater approved to ANSI Z21.11.2 standard .
An IHP hood must be installed when using a vent-free log heater (see Accessories, page 20).
FOR CANADA: The authority having jurisdiction
(such as the municipal building department, fire
department, etc.) should be contacted before
installation to determine the need to obtain a permit.
POUR LE CANADA: L’autorité compétente (comme le
service municipal du bâtiment, les pompiers, etc.) doit
être contacté avant l’installation afin de déterminer la
nécessité d’obtenir un permis.
This appliance may be installed in an aftermarket permanently located, manufactured home (USA only) or
mobile home, where not prohibited by local codes.
This installation manual will enable you to obtain a safe, efficient and dependable installation of your fireplace
system. Please read and understand these instructions before beginning your installation.
Do not alter or modify the fireplace or its components under any circumstances. Any modification or alteration of
the fireplace system, including but not limited to the fireplace, chimney components and accessories, may void the
warranty, listings and approvals of this system and could result in an unsafe and potentially dangerous installation.
IMPORTANT! TO ASSURE PROPER ALIGNMENT OF GLASS DOORS: INSTALL THIS FIREPLACE IN A SQUARE
AND PLUMB CONDITION, USING SHIMS AS NECESSARY AT SIDES AND/OR BOTTOM.
Ce manuel est disponible en francais, simplement
en faire la demande. Numéro de la pièce 127020-02.
NOTE: DIAGRAMS AND ILLUSTRATIONS THROUGHOUT THE MANUAL ARE NOT TO SCALE.

SuperiorFireplaces.us.com 127020-01_E2
SAFETY
WARNING: Improper installation, adjustment,
alteration, service or maintenance can cause injury,
property damage or loss of life. Refer to this manual
for assistance or additional information. Consult a
qualified installer or local distributor.
IMPORTANT: Check local codes before installing this
fireplace.
Before beginning installation of this fireplace, read these instructions
through completely.
• This INNOVATIVE HEARTH PRODUCTS (IHP) fireplace and its
components are safe when installed according to this installa-
tion manual. Unless you use IHP components, which have been
designed and tested for the fireplace system, you may cause a fire
hazard.
• The IHP warranty will be voided by and IHP disclaims any respon-
sibility for the following actions.
a. Modification of the fireplace, components, doors, air inlet system
and damper control.
b. Use of any component part not manufactured or approved by
IHP in combination with an IHP fireplace system.
Proper installation is the most important step in ensuring safe and
continuous operation of fireplace. Consult the local building codes
as to the particular requirements concerned with the installation of
all factory built fireplaces.
WARNING: Do not install a fireplace insert in this
box unless the manufacturer's instructions with the
insert specifically state this fireplace has been tested
for use with this insert.
TABLE OF CONTENTS
Safety............................................................................................. 2
Specifications................................................................................. 4
Fireplace Installation ...................................................................... 5
Venting Installation ........................................................................ 7
Optional Gas Line Installation ...................................................... 12
Operation and Maintenance Guidelines........................................ 13
Technical Service ......................................................................... 14
Replacement Parts....................................................................... 14
Important Notices - Canada ......................................................... 15
Parts ............................................................................................ 16
Accessories.................................................................................. 18
Draft Smoke Guidelines - Appendix A ......................................... 21
Warranty ...................................................................................... 23
Thank you for your purchase. We appreciate your
business!
Please carefully read and follow all instructions in this manual. Pay
special attention to all warnings and safety information.
Following these safety, care, and operation instructions will help
ensure many years of dependable and enjoyable service from your
fireplace.
Please read and understand these instructions before installing
or operating.
FOR YOUR SAFETY
• Do not store or use gasoline or any other flammable
vapors or liquids in the vicinity of this or any other
appliance.
• Due to high temperatures, the appliance should be
located out of traffic and away from furniture and
draperies.
• Do not place clothing or other flammable materials
on or near the appliance.
• Never leave children unattended when a fire is burn-
ing in the fireplace.
WARNING: Use solid wood or processed solid fuel
firelogs only. When processed wood fuel fire logs are
used, do not poke or stir the logs while they are burning.
Use only fire logs that have been evaluated for the ap-
plication in fireplace and refer to fire log warnings and
caution markings on packaging prior to use.
This fireplace is not intended to be used as a substitute
for a furnace to heat an entire home. Use for supple-
mental heat only.
Overfiring of a fireplace is a condition where excessive
temperaturesarereached,beyondthedesigncapabilities
of theappliance. Thedamage thatoccurs from overfiring
isnotcoveredunderthemanufacturer’slimitedwarranty.

SuperiorFireplaces.us.com
127020-01_E 3
SAFETY Continued
WARNING: CONTINUED OVERFIRING CAN PER-
MANENTLY DAMAGE YOUR FIREPLACE SYSTEM.
SOME EXAMPLES OF CONDITIONS THAT COULD
CAUSE OVERFIRING ARE:
• BURNINGQUANTITIESOFSCRAPLUMBER,PINE
BRANCHES, PAPER OR CARDBOARD BOXES
WHICH EXCEED THE VOLUME OF THE NORMAL
LOG FIRE.
• BURNING TRASH, CHEMICALS OR CHEMICALLY
TREATED COMBUSTIBLES.
Disposal of Ashes
Ashes should be placed in a metal container with a
tight-fitting lid. The closed container of ashes should
be placed on a noncombustible floor or on the ground,
well away from all combustible materials, pending
final disposal. If the ashes are disposed of by burial
in soil or otherwise locally dispersed, they should be
retained in the closed container until all cinders have
thoroughly cooled.
WHEN USING THE DECORATIVE APPLIANCE, THE
FIREPLACE DAMPER MUST BE SET IN THE FULLY
OPEN POSITION.
Never use gasoline, gasoline-type lantern fuel, kero-
sene, charcoal lighter fluid, or similar liquids to start
or ’freshen up’ a fire in this fireplace. Keep all such
liquids well away from the fireplace while it is in use.
Use SOLID WOOD only for fuel. It is best to use dry
and well seasoned hardwood. Softwoods tend to burn
veryquickly.DONOTusetreatedwood,charcoal,coal,
trash,driftwoodorwoodsthathavebeendippedintar,
pitch, pine tar, creosote, etc. Wood products made
with synthetic binders, such as plywood, produce ab-
normally high temperatures and sputtering, smoking
fires. When burning artificial logs, please read and
follow the instructions provided by the manufacturer.
Never burn treated construction lumber or scraps.
These woods burn excessively hot and may contain
chemicals used to treat insects and fungus. When
burned,thesechemicalscanposeasignificanthazard.
IMPORTANT: See appendix A, page 21 for additional
information regarding draft requirements, smoking
causes and troubleshooting.
WARNING:BURNINGIMPROPERFUEL(I.E.CHAR-
COAL) CAN RESULT IN CARBON MONOXIDE POISON-
ING, WHICH MAY LEAD TO DEATH!
Carbon Monoxide Poisoning – Early signs of carbon
monoxidepoisoningresemblethefluwithheadaches,
dizziness, or nausea. If you have these signs, get
fresh air at once! Have the appliance inspected by a
qualifiedservicetechnician. Somepeoplearemoreaf-
fectedbycarbonmonoxidethanothers. Theseinclude
pregnant women, people with heart or lung disease
or anemia, those under the influence of alcohol, and
those at high altitudes.
Ventilation Requirements - Provide adequate air for
combustion. The fresh air requirements of this ap-
pliance must be met within the space where it will
be installed.
Smoke Detectors - Since there are always several
potential sources of fire in any home, we recommend
installing smoke detectors. If possible, install the
smoke detector in a hallway adjacent to the room (to
reduce the possibility of occasional false activation
fromtheheat producedbythe appliance). Ifyourlocal
coderequires asmoke detectorbe installedwithin the
same room, you must follow the requirements of your
local code. Check with your local building department
for requirements in your area.
Creosote – Formation and Need for Removal
When wood is burned slowly, it produces tar and other
organic vapors, which combine with expelled mois-
ture to form creosote. The creosote vapors condense
in the relatively cool chimney flue of a slow-burning
fire. As a result, creosote residue accumulates on
the flue lining. When ignited this creosote makes an
extremely hot fire.
The chimney shall be inspected at least twice a year
duringtheheatingseasontodeterminewhenacreosote
builduphasoccurred. Whencreosotehasaccumulated
(1/8" [3 mm] or more) it shall be removed to reduce
the risk of a chimney fire.

SuperiorFireplaces.us.com 127020-01_E4
SPECIFICATIONS
GAS LINE
KNOCK OUTS
GAS LINE
KNOCK OUTS
ELECTRICAL
OUTLET
LEFT SIDE
RIGHT SIDE
AIR KIT
KNOCK OUT
7 1/8" (181 mm)
8 3/4" (223 mm)
8 3/4" (223 mm)
14 1/4"
(362 mm)
32 1/2" (826 mm)
11 1/4" (286 mm)
11 3/4"
(299 mm)
20 1/2"
(521 mm)
41 1/4"
(1048 mm)
5/8"
(16 mm)
9 1/8
" (232 mm)
9 1/8" (232 mm)
3 1/2"
(89 mm)
3 1/2"
(89 mm)
11 1/2" (292 mm)
22" (559 mm)
29" (737 mm)
41" (1042 mm)
1" (26 mm)
1" (26 mm)
21"
(534 mm)
8" (204 mm)
35" (889 mm)
37"
(940 mm)
41" (1042 mm)
1" (26 mm) AIRSPACE
TO COMBUSTIBLE
MATERIAL
0" (0 mm)
TO TOP
SPACERS
0" (0 mm)
TO BOTTOM 8" (204 mm)
EACH SIDE
NO COMBUSTIBLE
MATERIAL ON FACE
HEARTH EXTENSION
51" X 16" (1296 mm X 407 mm)
COMBUSTIBLE
WALL BOARD
NOT LESS THAN
12" (305 mm) TO
PERPENDICULAR
SIDEWALL
OUTSIDE AIR
(LEFT SIDE ONLY)
ROUND TOP TERMINATION
SQUARE CHASE-TOP TERMINATION
3/4" (19 mm)
AIR SPACE
BACK AND
SIDES
CAUTION: THE STRUCTURAL INTEGRITY OF THE MANUFACTURED HOME FLOOR, WALL, AND CEILING/ROOF
MUST BE MAINTAINED.

SuperiorFireplaces.us.com
127020-01_E 5
FIREPLACE INSTALLATION
4. Check the level of the fireplace and shim with sheet metal if neces-
sary.
5. Before securing fireplace to prepared framing, the ember protector
(provided) must be placed between the hearth extension (not sup-
plied) and under bottom front edge of fireplace to protect against
glowing embers falling through. If fireplace is to be installed on a
raised platform, a Z-type ember protector (not supplied) must be
fabricated to fit your required platform height. The ember protec-
tor should extend under fireplace a minimum of 1 1/2". The ember
protector should be made of galvanized sheet metal (28 gauge
minimum) to prevent corrosion.
6. Using screws or nails, secure fireplace to framing through flanges
located on sides of fireplace.
DRAIN PAN (DP36)
For outdoor installations, the fireplace enclosure must allow for
adequate drainage and fresh air ventilation. It is recommended that
a sealed, corrosion resistant catch pan with provision for drainage
be installed under the fireplace within the fireplace enclosure (see
Accessories on page 19).
41 3/4"
(1061 mm)
41 3/4"
(1061 mm)
21 7/8"
(556 mm)
Figure 1 - Framing Dimensions
Figure 2 - Corner Installation
SELECTING LOCATION
WARNING: DO NOT INSTALL IN SLEEPING ROOM
OF MOBILE HOMES.
To determine the safest and most efficient location for the fireplace,
you must take into consideration the following guidelines:
1. The location must allow for proper clearances (see Figures 1 and
2).
2. Consider a location where the fireplace will not be affected by
drafts, air conditioning ducts, windows or doors.
3. A location that avoids the cutting of joists or roof rafters will make
installation easier.
4. An outside air kit is available with this fireplace (see Optional Outside
Air Kit on page 7).
MINIMUM CLEARANCE TO COMBUSTIBLES
Ceiling 40" (1016 mm) minimum
Back and sides of fireplace 3/4" (19 mm) minimum*
Floor** 0" (0 mm) minimum
Perpendicular wall to opening 12" (305 mm) minimum
Top spacers 0" (0 mm) minimum
Mantel clearances see Mantels, page 6.
Chimney outer pipe surface 1" (26 mm) minimum
* Not required at nailing flanges
** See step 2 of Framing
WARNING: Do not pack required air spaces with
insulation or other materials.
Minimum/Maximum Chimney Height for Residential Installation
The minimum height of the chimney, measured from the base of
the fireplace to the flue gas outlet of the termination, is 14.5 feet for
straight flue or a flue with one elbow set. The maximum distance
between elbows is 6 feet. For systems with two elbow sets, the
minimum height is 22 feet. The maximum height of any system is
50 feet. This measurement includes the fireplace, chimney sections
and the height of the termination assembly at the level of the flue gas
outlet (see Figure 18, page 11).
Minimum/Maximum Chimney Height for Outdoor Installation
The minimum height of the chimney, measured from the base of the
fireplace to the flue gas outlet of the termination, is 7 1/2feet (minimum
of 4 feet of chimney pipe sections required for outdoor installation).
FRAMING
1. Frame opening for fireplace using the dimensions shown in Figures
1 and 2.
2. If fireplace is to be installed directly on carpeting, tile or any
combustible material other than wood flooring, the fireplace must
be installed upon a metal or wood panel extending the full width
and depth of fireplace.
3. Set fireplace directly in front of this opening and slide unit back
until nailing flanges touch side framing.
Maintain 3/4
"
Clearance at
Sides and
Back of
Fireplace
3/4" Clearance Not
Required at Nailing Flanges
24 1/2"
(623 mm)
52 1/4"
(1328 mm)
17 3/8"
(442 mm)
73 7/8" (1877 mm)

SuperiorFireplaces.us.com 127020-01_E6
OPTIONAL OUTSIDE AIR KIT (MODEL AK4/AK4F)
The installation of an outside air kit should be performed during the
rough framing of the fireplace due to the nature of it's location. Outside
combustion air is accessed through a vented crawl space (AK4F) or
through a sidewall (AK4). See Figure 22 on page 13 for instruction of
operating air kit.
CAUTION: Combustion air inlet ducts shall not
terminate in attic space.
The maximum height for the air vent can not exceed
3 feet below the flue gas outlet of the termination.
HEARTH EXTENSION
A hearth extension projecting a minimum of 16" in front of and a
minimum of 8" beyond each side of the fireplace opening is required
to protect combustible floor construction in front of the fireplace.
Fabricate a hearth extension using a material which meets the fol-
lowing specifications: a layer of noncombustible, inorganic material
having a thermal conductivity of k=0.84 BTU IN/FT, HR. F (or less) at
1" thick. For example, if the material selected has a k factor of 0.25,
such as glass fiber, the following formula would apply:
0.25 x 1.0" = 0.30" thickness required
0.84
Thermal conductivity "k" of materials can be obtained from the manu-
facturer or supplier of the noncombustible material. If the hearth
extension is to be covered, use noncombustible material such as
tile, slate, brick, concrete, metal, glass, marble, stone, etc. Provide
a means to prevent the hearth extension from shifting and seal gap
between the fireplace frame and hearth extension with a noncom-
bustible material (see Figure 3).
WARNING: Hearth extension is to be installed only
as shown in Figure 3.
Figure 3 - Hearth Extension
Seal Gap
Fireplace Front
Ember Protector
Fireplace Front Raised
Hearth
Fireplace Front Elevated
Ember Protector
Ember Protector
Seal Gap
Hearth
Extension
MANTELS
A mantel may be installed if desired (see Figure 4). Woodwork such
as wood trims, mantels or any other combustible material project-
ing from the front face must not be placed within 12" of the fireplace
opening. Combustible materials above 12" and projecting more than
11/2" from the fireplace must not be placed less than 15" from the
top opening of the fireplace (NFPA 211, Section - Clearance from
Combustible Material).
Mantels or any other combustible material also may come up to the
side edge of the black metal face of the fireplace just as long as the
projection from the front face fall within the limit shown in Figure 4.
Figure 4 - Mantel Clearances to Combustible Material
FIREBOX
SAFE ZONE
Top View of Fireplace
2" (51 mm) Max.
3.0"
(77 mm)
Min. to
Perpendicular
Side Wall
12" (305 mm)
8" (204 mm)
33°
Combustible
Material Must Not
Overlap Front Face
FIREPLACE INSTALLATION Continued
12 1/4"
(312 mm)
Ref.
12"
(305 mm)
Min.
9"
(229 mm)
Min.
6"
(153 mm)
Ref.
11/2"
(38 mm)
Max.
3" (77 mm)
Nom.
33°
Combustible
Material
Safe Zone for
Projection of
Combustible
Materials
Fireplace Opening
Upper
Section of
Fireplace

SuperiorFireplaces.us.com
127020-01_E 7
Figure 6 - Lineal Gain
Hemmed
End
8" Stainless
Inner Pipe
12 3/8" Galvanized
Outer Pipe
LINEAL GAIN
PART NO. DESCRIPTION GAIN
36" Fireplace 40 "
12-8DM
12-8HT Pipe Section 10 5/8
"
18-8DM
18-8HT Pipe Section 16 5/8
"
24-8DM
24-8HT Pipe Section 23 5/8
"
36-8DM
36-8HT Pipe Section 34 5/8
"
48-8DM
48-8HT Pipe Section 46 5/8
"
RT-8DM Round Termination 6 7/8 "
*
RTL-8DM Round Termination 7 3/4 "
*
RTT-8DM Round Termination with Slip Section 6 7/8
" to
23 1/8"*
RTTL-8DM Round Termination with Slip Section 8 1/2
" to
21 1/2"*
ET-8DM Square Chase-Top 12 "
*
ETO-8DM Square Chase-Top with Mesh 12 "
*
ETL-8DM Square Chase-Top with Slip Section 7" to
15"*
ETLO-8DM Square Chase-Top with Mesh & Slip Sec-
tion
12 " to
25 1/2" *
* The lineal gain for the terminations is measured to the flue gas
outlet height.
Figure 5 - Outside Air Kit
Secure to Collars with Metal Tape, Screws or Straps
(Min. of 1/4" x 20" in size)
Air Inlet
Location Must
Allow For
Bushes or
Snow
Vent Hood
Required for
Wall Installation
Air Inlet
Eyebrow
Vented Crawl Space
(Check Local Codes Before
Installing in a Vented Crawl Space)
VENTING INSTALLATION
CHIMNEY PIPE
WARNING: Label part number 900599-01 must
be applied by the installer to all chimney pipe
sections but is not required on sections that will
be visible after the installation is complete. Label
must wrap around the circumference of the pipe.
See accessories, page 20 for Kit F2659.
The IHP chimney system consists of 12", 18", 24", 36" and 48" snap-
lock, double-wall pipe segments, planned for maximum adaptability to
individual site requirements. Actual lengths gained after fitting overlaps
must be taken into consideration (lineal gain) and are given in the lineal
gain chart (see Figure 6). Lineal gain is the actual measurable length of
a part after two or more parts are connected. For Canada, use chimney
parts designated "HT".
A SSEMBLY AND INSTALLATION OF DOUBLE WALL CHIMNEY
SYSTEM
Each double wall chimney section consists of a galvanized outer pipe,
a stainless steel inner flue pipe and a wire spacer. The pipe sections
must be assembled independently as the chimney is installed.
When connecting chimney directly to the fireplace, the inner flue
pipe section must be installed first with the lanced side up. The outer
pipe section can then be installed over the flue pipe section with the
hemmed end up. Press down on each pipe section until the lances
securely engage the hem on the fireplace starter. The wire will as-
sure the proper spacing between the inner and outer pipe sections.
Continue to assemble chimney sections as outlined, making sure
that both the inner and outer pipe sections are locked together. When
installing double wall snap-lock chimney together, it is important to
assure the joint between the chimney sections is locked. Check by
pulling chimney upward after locking. The chimney will not come
apart if properly locked. It is not necessary to add screws to keep the
chimney together (exception - see Figure 9, page 9).
The height of a vertical chimney pipe supported ONLY by the
fireplace, must not exceed 20 feet. Chimney heights above 20 feet
must be supported.
WARNING: The opening in collar around chimney
at top of fireplace must not be obstructed. Never use
blown insulation to fill chimney enclosure.

SuperiorFireplaces.us.com 127020-01_E8
VENTING INSTALLATION Continued
Figure 7 - Typical Offset Terminations
Figure 8 - Ceiling Support Pipe 12S-8DM
2" Min.
Straps Straps
Straps
Straps
Detail A Return Elbow Detail B Angle Firestop
See Detail A
See Detail B
Ceiling Support Pipe
12S-8DM
USING ELBOW OFFSETS (30E-8DM)
1. To achieve desired offset, you may install combinations of 12",
18", 24", 36" and 48" length of double wall pipe (see offset chart,
page 9 and Figure 7).
2. Chimney weight above offset rests on return elbow. Straps must
be securely nailed to rafters or joists (see Figure 8, details A and
B).
3. Maximum length of pipe between supports (return elbow or 12S-
8DM) is 6' of angle run. Maximum of two 6' angle run sections
per chimney system (see Figure 7).
4. All pipe connections between offset and return must be secured
with two screws on outer pipe only (see Figure 9, page 9). Do not
penetrate inner stainless.
Return
Elbow
Return
Elbow Return
Elbow
Offset
Elbow Offset
Elbow
Return
Elbow
Return
Elbow
Offset
Elbow
Offset
Elbow
Offset
Elbow
6' (1.83 m) Max.
6' (1.83 m) Max. 6' (1.83 m) Max.
6' (1.83 m) Max.
6' (1.83 m) Max.
A B C
Ceiling Support
Pipe 12S-8DM
6' (1.83 m) Max.

SuperiorFireplaces.us.com
127020-01_E 9
OFFSET CHART (22-50 FT. SYSTEM HEIGHT)
Figure 9 - Elbow Offset
Figure 10 - Firestop Spacer with Living Space Above Ceiling
Figure 11 - Firestop Spacer with Attic Space Above Ceiling
Existing Ceiling
Frame
Firestop
Spacer
Screws or Staples
(Min. of 8)
Firestop
Spacer
Screws or Staples
(Min. of 8)
Existing
Ceiling Frame
B
A
Screws
VENTING INSTALLATION Continued
FIRESTOP SPACERS (3600FS-8DM-1)
Firestop spacers are required at each point where the chimney penetrates
a floor space. Their purpose is to establish and maintain the required
clearance between the chimney and the combustible materials. When
the pipe passes through a framed opening into a living space above, the
firestop must be placed onto the ceiling from below as shown in Figure 10.
They also provide complete separation from one floor space to another
or attic space as required by most codes. When the double wall pipe
passes through a framed opening into an attic space, the firestop must
be placed into an attic floor as shown in Figure 11.
NOTICE: The installation of a firestop thimble (FST30
or 38FST) is recommended when negotiating a joist
and to prevent intrusion from insulation.
OFFSET RISE CHIMNEY LENGTH
A B 48" 36" 24" 18" 12"
4 3/8" 16 3/8"ELBOW SET ONLY
9" 25 3/4" 1
11 7/8" 31" 1
15" 37 3/8" 1
16 3/4" 40 1/2" 1 1
20" 47 1/8" 1
22 5/8" 52 1/8" 1 1
25 1/2" 57 7/8" 1
27 5/8" 62" 1 1
30 3/8" 67 1/4" 1 1
33" 72 5/8" 1 1
35 3/4" 78" 2
37 7/8"82" 1 1 1
41 1/4" 88 5/8" 1 1
43 3/8" 92 3/4" 2 1
46 5/8" 99 3/8" 2
48 3/4" 103 1/2" 1 1 1
51 1/2" 108 7/8" 2 1
54 1/4" 114 1/8" 2 1
57" 119 1/2" 1 2
59" 123 5/8" 2 1 1
61 3/4" 129" 1 2 1
64 1/2" 134 3/8" 1 2 1
67 1/4" 139 5/8" 4
Figure 11a - Firestop Thimble
Thimble 38FST
or FST30
Firestop

SuperiorFireplaces.us.com 127020-01_E10
14
3
/
8
"
(36.5 cm)
30"
(76.2 cm)
1"
(2.5
cm)
1"
(2.5
cm)
Minimum Measurements
1"
(2.5 cm)
Opening "A"
Pitch Slope Opening "A"
Max.
Used Flashing
Model No.
Flat 0° 15" V6F-8DM
0-6/12 26.6° 16 1/8" V6F-8DM
6/12-
12/12 45.0° 20 3/8" V12F-8DM
Figure 12 - Roof Opening Measurements
Nail Only Outer
Perimeter of
Flashing
Storm Collar
Flashing Cone
Underlap Shingles
at Bottom
Overlap Shingles
Top and Sides Only
Figure 13 - Flashing Installation
Figure 14 - Storm Collar
Chimney Pipe Waterproof
Caulk
Storm Collar Flashing
VENTING INSTALLATION Continued
PENETRATING ROOF
To maintain a 1" clearance to the pipe on a roof with a pitch, a rect-
angular opening must be cut.
1. Determine center point through which pipe will penetrate roof.
2. Determine center point of roof. Pitch is the distance the roof drops
over a given span, usually 12". A 6/12 pitch means that the roof
drops 6" for each 12" one measure horizontally down from the
roof rafters.
3. Use roof opening chart (Figure 12) to determine the correct open-
ing length and flashing required.
4. Remove the shingles around opening measured. Cut out this
section.
5. Add next sections of pipe until end penetrates roof line. Check to
see that the proper clearances are maintained. Extend chimney by
adding sections of double wall pipe until pipe is minimum of 30"
above the highest point of the roof cutout. Termination and chimney
must extend a minimum of 36" above the highest point where it
passes through the roof.
FLASHING INSTALLATION (V6F-8DM OR V12F-8DM)
Determine the flashing to be used with the roof opening chart. Slide
flashing over pipe until base is flat against roof. Replace as many
shingles as needed to cover exposed area and flashing base. Secure
in position by nailing through shingles (see Figure 13). DO NOT NAIL
THROUGH FLASHING CONE.
Installing Flashing on a Metal Roof
When installing flashing on a metal roof, it is required that putty tape be
used between the flashing and roof. The flashing must be secured to the
roof using #8 x 3/4" screws and then sealed with roof coating to prevent
leakage through screw holes. A roof coating must also be applied around
perimeter of flashing to provide a proper seal.
Storm Collar Installation (SC1 or SC2)
Place storm collar over pipe and slide down until it is snug against the open
edge of the flashing (see Figure 14). Use SC1 for all round terminations
and SC2 for all terminations with slip sections. Apply waterproof caulk
around the perimeter of the collar to provide a proper seal.
Terminations/Spark Arrestor
The fireplace system must be terminated with the listed round top or
chase terminations. In any case, refer to the installation instructions
supplied with the termination. The termination approved for this fire-
place are the RT-8DM and RLT-8DM that can be used for flashing or
chase and ET-8DM, ETO-8DM, ETL-8DM and ETLO-8DM for chase
style termination only. Figure 15, page 11 shows an RLT-8DM round
top termination.
CAUTION: Do not seal openings on the rooftop
flashing. Follow the installation instructions provided
with the termination being used.
Terminations with 16" slip pipe sections are available. The RTT-8DM
and RLTT-8DM are approved for flashing installations. When needed,
these adjustable terminations may be used in combination with the
pipe assembly to achieve the correct chimney height.
Note: In the rare instance there is a problem with the side driven rain
or wind or the chimney is not drafting properly, an ADS-8DM (Anti-
Draft Shield) can be used with round terminations.

SuperiorFireplaces.us.com
127020-01_E 11
Figure 15 - Termination
Attach Bracket Tabs to
Outer Pipe (3 Places)
Secure with Screws
RLT-8DM
Level of Flue
Gas Outlet
Caulk
Collar
Flashing
Underlap Shingles
Bottom Only
Overlap Shingles
Top and Sides
Figure 16 - Multiple Chase Installation
CHASE INSTALLATIONS
Instructions for chase installations are included with the chase style
termination chosen. In a multiple chase installation, be sure to provide
adequate distance between terminations to prevent smoke spillage
from one termination to another. We suggest that terminations be
separated at least 24", center to center and stacked at a vertical height
difference of 18" (see Figure 16).
Note: If a decorative shroud is to be installed, contact the manufac-
turer for specifications.
10 FOOT RULE
All flue gas outlet chimney terminations must extend a minimum of
3 feet in height above the highest point where it passes through the
roof and must be at least 2 feet above the highest point of the roof
that is within a horizontal distance of 10 feet (see Figure 17).
FINISHING FIREPLACE
Combustible materials, such as wallboard, sheet rock, drywall, ply-
wood, etc. may make direct contact with sides and top around the
fireplace face. It is important that combustible materials do not overlap
the face itself. Brick, glass, tile or other noncombustible materials
may overlap the front face provided they do not obstruct essential
openings like louvered slots or any other opening. When overlapping
with a noncombustible facing material, use only noncombustible
mortar or adhesive.
VENTING INSTALLATION Continued
Figure 17 - 10 Foot Rule
Figure 18 - Typical Residential Installations
10'
(3.05 m)
10'
(3.05 m)
2' (0.61 m)
Min.
2' (0.61 m) Min.
3' (0.92 m)
Min.
3' (0.92 m)
Min.
Level of
Flue Gas Outlet
24" (610 mm)Min.
24" (610 mm)Min.
18"
(458 mm)
Min. Typ.
EFFECTIVE HEIGHT
OF TERMINATION CAP
EFFECTIVE HEIGHT
OF TERMINATION CAP
EFFECTIVE HEIGHT
OF TERMINATION CAP
EFFECTIVE HEIGHT
OF TERMINATION CAP
30E-8DM 30E-8DM
UP TO
6 FT (1.83 m)
MAX.
UP TO
6 FT (1.83 m)
MAX.
14.5 FT
(4.42 m)
MINIMUM
HEIGHT
14.5 FT
(4.42 m)
MINIMUM
HEIGHT
MAX. HEIGHT
50 FT (15.24 m)
ANY SYSTEM
MIN. HEIGHT OF
22 FT. (6.71 m) WITH
2 ELBOW SETS
MAX. HEIGHT OF
50 FT. (15.24 m)

SuperiorFireplaces.us.com 127020-01_E12
OPTIONAL GAS LINE INSTALLATION
Figure 19 - Gas Line Knockout
Side Firebrick
Finished Side
Refractory
Knockout Plug
Outside of
Fireplace
Gas Line
Conduit
Insulation
Gas
Conduit
Cover
1/2" Dowel
Gas line hook up should be done by your supplier or a qualified
service person.
Note: Before you proceed, make sure your gas supply is turned off.
Use only a 1/2" black iron pipe and appropriate fittings.
1. Remove knockout indentation on refractory or firebrick wall lo-
cated above the refractory hearth floor. The knockout indentation
must be firmly tapped with any solid object such as a 1/2" dowel
until it is released. Remove fragmented portions of refractory (see
Figure 19).
2. Remove gas line cover plate located on either side of fireplace and
pull out insulation from gas line conduit sleeve. Save insulation
for reuse. Replace screws.
3. Run a 1/2" black iron gas line into the fireplace through the rear
at gas line conduit sleeve (if using a raised platform, add height).
Provide sufficient gas line into fireplace chamber for fitting con-
nection (see Figure 20). Note: Secure incoming gas line to wood
framing to provide rigidity for threaded end.
4. Repack insulation around gas line and into sleeve opening. Seal
any gaps between gas line and refractory knockout hole with
refractory cement or commercial furnace cement, Install the gas
appliance or cap-off gas line if desired.
CAUTION: All gas piping and connections must be
tested for leaks after the installation is completed.
After ensuring that the gas valve is on, apply soap and
water solution to all connections and joints. Bubbles
formingshowaleak. Correctallleaksatonce. DONOT
USEAN OPENFLAME FORLEAK TESTINGAND DONOT
OPERATE ANY APPLIANCE IF A LEAK IS DETECTED.
LEAK TESTING SHOULD BE DONE BY A QUALIFIED
SERVICE PERSON.
Note: An IHP hood must be installed when using an unvented gas
log set (see Accessories on page 20).
WARNING: Do not operate an unvented gas log set in
this fireplace with the chimney removed.
If you install a decorative gas appliance (vented gas log), the deco-
rative gas appliance must comply with the Standard for Decorative
Gas Appliance for Installation in Solid Fuel Burning Fireplaces, ANS
Z21.60 or Z21.84 and shall also be installed in accordance with the
National Fuel Gas Code, ANSI 7223NFPA 54 latest edition.
WARNING:Toavoidtheriskofdamagingthefireplace
materials and increasing the risk of spreading a fire,
do not use the fireplace to cook or warm food.
Seal
Opening
with
Refractory
Cement
Outside of
Fireplace
Gas Line Conduit
Repack
Insulation
Incoming
1/2" Black
Iron Pipe
Side Firebrick
Finished Side
Provide Enough Threaded
End for Fitting Connection
Figure 20 - Gas Line Installation
WARNING: If the fireplace has been used for wood
burning, the firebox and chimney must be cleaned
of soot, creosote and ashes be a qualified chimney
cleaner. Creosote will ignite if heavily heated.
WARNING: When using a decorative vented gas log,
the damper must be removed or permanently locked in
the fully open position and the glass doors must be in
the fully open position.

SuperiorFireplaces.us.com
127020-01_E 13
Doors Fully Closed
Fireplace Front
Doors Fully Opened
Fireplace Front
OPERATION AND MAINTENANCE GUIDELINES
Figure 21 - Glass Doors
GLASS DOORS
Glass doors are optional with the fireplace. When the fireplace is in
operation, doors must be fully opened or fully closed position only
or a fire hazard may be created (see Figure 21).
A fireplace equipped with glass doors operates mush differently
than a fireplace with an open front. A fireplace with glass doors has
a limited amount of air for combustion. Excessive heat within the
fireplace can result if too large a fire is built or if the combustion air
gate is not completely open.
The following tips should be followed to assure that both the fireplace
and the glass door retain their beauty and function properly. Both the
flue damper and the glass doors must be fully opened before starting
the fire. This will provide sufficient combustion air and maintain safe
temperatures in the firebox.
IMPORTANT: The glass must be allowed to warm slowly and evenly.
The tempered glass will withstand a gradual temperature rise to 550°
F, which is more than a normal fire will generate. Such materials as
pitch/wax laden logs, very dry mill end lumber and large amounts
of paper or cardboard boxes can create an excessively hot fire and
should not be burned in this fireplace. Always keep the fire well back
from the doors and never allow flames to contact the glass.
WARNING: Fireplaces equipped with glass doors
should be operated only with doors fully opened or
doorsfully closed.Doors, ifleft partlyopen, maydraw
gas and flame out of the fireplace opening creating
risks of both fire and smoke.
WARNING: Discontinue use of the appliance imme-
diately if doors are damaged and contact a qualified
installer for repair. Only doors certified with the ap-
pliance shall be used.
WARNING: Do not slam or strike doors. Damage
can result in a hazardous condition.
Cleaning Glass
Clean the glass with any commercial glass cleaner or soap and
water. Do not use any abrasive material to clean the glass. Do not
clean the glass with any cool water is the glass is still hot from the
fire and smoke.
A gas line or gas log lighter may be installed for the purpose of
installing a vented or vent-free decorative gas appliance incorporat-
ing an automatic shutoff device and complying with the Standard
for Decorative Gas Appliances for Installation in Vented Fireplaces,
ANSI Z21.60 or American Gas Association draft requirements for
Gas Fired Log Lighters for Wood Burning Fireplaces, Draft NO. 4
dated August, 1993.
If you wish to install an unvented (vent-free) gas log set, only unvented
gas log sets which have been found to comply with the standard for
unvented room heaters, ANSI Z21.11.2 are to be installed in this
fireplace.
OUTSIDE AIR AND DAMPER HANDLE OPERATION
The damper handle, which opens and closes the damper blade, is
located in the upper front face of the fireplace. Pushing the handle into
the left of the keyway slot will free the damper blade to automatically
open. Pushing the handle in to the right will lock the damper blade
closed (see Figure 22).
The outside air kit handle is located at the left hand side of the fireplace
(see Figure 22). Pulling the handle out will free the outside air door
to open. Pushing the handle in will lock the door closed.
Figure 22 - Damper and Air Kit Handle
OPEN CLOSE
Handle
Outside Air Kit
Handle
Keyway Slot
Handle Retainer
WARNING: Risk of fire! Replace grate with IHP
model 111028-01 (J4491) only. This grate has been
designed to keep the operation of your fireplace safe
and efficient.

SuperiorFireplaces.us.com 127020-01_E14
OPERATION AND MAINTENANCE GUIDELINES
Continued
LOCATING ACCESS COVER PLATE
Sheet metal cover plates located underneath front hearth refractory may
have shifted or moved out of place while fireplace was in transit. These
cover plates must be kept in the proper location prior to using the fireplace
(See Figure 23).
For further operating guidelines, instructions and warranty infor-
mation, please refer to your homeowner's guide or contact your
authorized dealer.
Figure 23 - Locating Access Cover Plate
Access Panel
REPLACEMENT PARTS
See Pages 16 to 18 for a complete replacement parts list. Use only
parts supplied from the manufacturer.
Normally, all parts should be ordered through your IHP distributor
or dealer. Parts will be shipped at prevailing prices at time of order.
When ordering repair parts, always give the following information:
1. The model number of the fireplace.
2. The serial number of the fireplace.
3. The part number.
4. The description of the part.
5. The quantity required.
6. The installation date of the fireplace.
If you encounter any problems or have any questions concerning the
installation or application of this fireplace, please contact your dealer.
IHP
1508 Elm Hill Pike, Suite 108
Nashville, TN 37210
Visit us at SuperiorFireplaces.us.com
TECHNICAL SERVICE
You may have further questions about installation, operation, or
troubleshooting. Please contact your IHP dealer for any questions
or concerns. When contacting your dealer please have your model
and serial numbers of your fireplace ready. You can also visit our web
site at SuperiorFireplaces.us.com.

SuperiorFireplaces.us.com
127020-01_E 15
IMPORTANT NOTICES - CANADA
IMPORTANT NOTICE
A manufactured shroud which
has been approved by a na-
tional testing agency for use
with this fireplace may be used
if installed in accordance with
the instructions by its manu-
facturer. A locally fabricated
shroud may be used with IHP
Shroud Leg Spacer Kit (SLK)
in accordance with instructions
provided with the shroud.
Canadian code CAN/ULC-S610-M87 and other pertinent
codes require stainless steel chimney for the installation
of this fireplace. A Cold Air Climate Kit is also required
in Canada and is recommended for cooler regions in the
United States. Below, find a list of approved stainless
steel parts.
Chimney Parts List for Canada
Catalog
No. Model No. 8" Hi-Temp Wood burning Chimney
F0881 12-8HT 12" Section Hi-Temp Double
Wall Pipe Snap Lock
F0882 18-8HT 18" Section Hi-Temp Double
Wall Pipe Snap Lock
F0883 24-8HT 24" Section Hi-Temp Double
Wall Pipe Snap Lock
F0884 36-8HT 36" Section Hi-Temp Double
Wall Pipe Snap Lock
F0885 48-8HT 48" Section Hi-Temp Double
Wall Pipe Snap Lock
F0886 30E-8HT 30 Degree Hi-Temp Offset
and Return
F0887 12S-8HT Hi-Temp Chimney Support
(For Use With Chimney
Heights In Excess of 30')
F0888 RT-8HT Hi-Temp Round Top with
Mesh Screen
F0889 RTT-8HT* Hi-Temp Round Top with
Mesh Screen and Slip Sec-
tion
F0890 RLT-8HT Hi-Temp Round Top with
Louvered Screen
F0891 RLTT-8HT* Hi-Temp Round Top with
Louvered Screen and Slip
Section
F0892 ET-8HT* Hi-Temp Pyramid Top with
Slip Section
F0893 ETL-8HT* Hi-Temp Large Pyramid Top
with Slip Section (use with all
8" systems)
F0894 AP-8HT Hi-Temp Anchor Plate/Col-
lar Assembly (for masonry
fireplaces)
F0929 CAK-8 Cold Air Collar Kit - 8"
Chimney
*When ordered alone, this part cannot ship via parcel
delivery services.
NOTICE: The firebox canopy (hood)
must not be modified or replaced with
a canopy that may be provided with
the unvented decorative room heater.
CAUTION: THE STRUCTURAL INTEG-
RITY OF THE MANUFACTURED HOME
FLOOR, WALL, AND CEILING/ROOF
MUST BE MAINTAINED.
WARNING: DO NOT INSTALL
IN SLEEPING ROOM OF MOBILE
HOMES.

SuperiorFireplaces.us.com 127020-01_E16
PARTS
9
24
16
31 25
16
4 30
32
19
12
23
20
28
17
8
1
5
21
2
18
11
14
3
13
22
10 6
29
7
33/34
26
27
15
MODEL CATALOG NO.
WRE3036WS F0449
WRE3036WH F0450

SuperiorFireplaces.us.com
127020-01_E 17
PARTS
This list contains replaceable parts used in your fireplace. When ordering parts, see Replacement Parts on page 14 of this manual.
KEY
NO. CATALOG NO. DESCRIPTION QTY.
1** Insulation Pan 1
2 ** Fireplace Top 1
3 ** Fireplace Surround 1
4 J3946 Air Rod Retainer 1
5 J3947 Damper Rod Retainer 1
6 ** Firebox Bottom 1
7** Firebox Surround 1
8 ** Air Separator 1
9See page 18 Left, Refractory Brick Liner 1
10 See page 18 Right, Refractory Brick Liner 1
11 See page 18 Rear, Refractory Brick Liner 1
12 See page 18 Bottom Rear Refractory, Brick Liner 1
13 See page 18 Bottom Front Refractory, Brick Liner 1
14 ** Firebox Support Leg 4
15 ** Damper Can Collar 1
16 J8012 Kit, Screen Assembly 1
17 ** Firebox Top Assembly 1
18 J3980 Air Kit Door Assembly 1
19 ** Face Weldment 1
20 J4470 Air Deflector 1
21 ** Fireplace Top Insulation 1
22 J4052 Access Panel 1
23 J4491 Grate 1
24 ** Collar Insulation 1
25 J6893 Chimney Starter Collar 1
26 J6895 Refractory Retainer 2
27 J3939 Grate Retainer 2
28 J4504 Door Stop 1
29 J4523 Pivot Clip 2
30 J6905 Spring Clip 2
31 J6918 Top Spacer 4
32 J6934 Conduit Plate Cover 4
33 J6951 Gas Conduit 2
34 J6952 Gas Conduit 2
PARTS AVAILABLE NOT SHOWN
106625-01 Home Owner’s Guide 1
J6906 Ember Protector 2
** Not a field replaceable part
WARNING: Contact an IHP dealer to obtain any of these parts. Never use substitute materials not approved
by IHP. Use of non-approved parts can result in poor performance and safety hazards.
MODEL CATALOG NO.
WRE3036WS F0449
WRE3036WH F0450

SuperiorFireplaces.us.com 127020-01_E18
PARTS
KEY
NO.
CATALOG
NO. DESCRIPTION
WRE3036WS
F0449
WRE3036WH
F0450 QTY.
1 F3286 30 series White Stacked Refractory Set, 36" •
2 --- Refractory, Lt, Std, White S36 • 1
3 --- Refractory, Rt, Std, White S36 • 1
4 --- Refractory, Rear, Std, White S36 • 1
5 --- Refractory, Btm Rear White S36 • 1
6 --- Refractory, Btm Frnt, White S36 • 1
1 F3287 30 series White Herringbone Refractory Set, 36" • 1
2 --- Refractory, Lt, Her, White S36 • 1
3 --- Refractory, Rt, Her, White S36 • 1
4 --- Refractory, Rear, Her, White S36 • 1
5 --- Refractory, Btm Rear White S36 • 1
6 --- Refractory, Btm Frnt, White S36 • 1
1
2
43
6
5
Stacked Refractory Shown
ACCESSORIES
REFRACTORY STAIN KITS
Use the refractory stain kits to give white refractory panels a new look.
Kit includes foam roller handle, paint tray, and one can of stain. Available stain colors
are creamer (ivory), Rust (terra cotta), and Cappuccino (rosy taupe). CappuccinoRustCreamer
CAT NO. MODEL DESCRIPTION
H8176 BSK-CR Stain Kit (Rfry) 1 Qt. Creamer
H8177 BSK-RT Stain Kit (Rfry) 1 Qt. Rust
H8178 BSK-CP Stain Kit (Rfry) 1 Qt. Cappuccino
MODEL CATALOG NO.
WRE3036WS F0449
WRE3036WH F0450

SuperiorFireplaces.us.com
127020-01_E 19
ACCESSORIES Continued
BI-FOLD GLASS DOORS
CAT NO. MODEL DESCRIPTION
F0987 BDO36 36" Outdoor Bi-Fold Glass Door - Black finish
F0988 BDO36B 36" Outdoor Bi-Fold Glass Door - Brushed Brass finish
F0989 BDO36P 36" Outdoor Bi-Fold Glass Door - Platinum finish
DOUBLE WALL PIPE
F0895 12-8DM 12" Section Double Wall Pipe Snap Lock
F0896 18-8DM 18" Section Double Wall Pipe Snap Lock
F0897 24-8DM 24" Section Double Wall Pipe Snap Lock
F0898 36-8DM 36" Section Double Wall Pipe Snap Lock
F0899 48-8DM 48" Section Double Wall Pipe Snap Lock
F0881 12-8HT 12" Section Hi-Temp Double Wall Pipe Snap Lock
F0882 18-8HT 18" Section Hi-Temp Double Wall Pipe Snap Lock
F0883 24-8HT 24" Section Hi-Temp Double Wall Pipe Snap Lock
F0884 36-8HT 36" Section Hi-Temp Double Wall Pipe Snap Lock
F0885 48-8HT 48" Section Hi-Temp Double Wall Pipe Snap Lock
30° OFFSET AND RETURN
F0900 30E-8DM 30 Degree Offset and Return
OPTIONAL OUTSIDE AIR KIT FOR FLOOR INSTALLATION
F1091 AK4 Complete Outside Air Kit w/Collars Hood & 3' Flex
OPTIONAL OUTSIDE AIR KIT FOR SIDEWALL INSTALLATION
F1093 AK4F Outside Air Kit Collar, Hood & 3' Flex for Floor Venting
STORM COLLAR
F0915 SC1-1 Storm Collar
FIRESTOP SPACER
F0907 3600FS-8DM-1 1" Clearance Firestop Spacer
ROOF FLASHING
F0909 V6F-8DM Roof Flashing 0 to 6/12 Pitch (30" Base)
F0910 V12F-8DM Roof Flashing 6/12 to12/12 Pitch

SuperiorFireplaces.us.com 127020-01_E20
ANTI-DRAFT SHIELD
(Round Top Termination Only)
F0927 ADS-8DM Anti-Draft Shield for Round Top Only
MESH ROUND TOP TERMINATIONS
F0916 RT-8DM Round Top with Mesh Screen
F0888 RT-8HT Hi-Temp Round Top with Mesh Screen
MESH ROUND TOP TERMINATIONS WITH SLIP SECTION
F0917 RTT-8DM Round Top with Slip Section & Mesh
F0889 RTT-8HT Hi-Temp Round Top w/Mesh Screen and Slip Section
ROUND TOP TERMINATIONS WITH LOUVERS
F0918 RLT-8DM Round Top with Louvered Screen
F0890 RLT-8HT Hi-Temp Round Top with Louvered Screen
ROUND TOP TERMINATIONS WITH LOUVERS W/SLIP SECTION
F0919 RLTT-8DM Round Top with Slip Section & Louvers
F0891 RLTT-8HT Hi-Temp Round Top w/Lvrd. Screen and Slip Section
SQUARE TOP TERMINATION WITH LOUVERS
F0920 ET-8DM Square Top
F0892 ET-8HT Hi-Temp Pyramid Top with Slip Section
SQUARE TOP TERMINATION WITH LOUVERS AND SLIP SECTION
F0921 ETL-8DM Square Top with Slip Section
F0893 ETL-8HT Hi-Temp Large Pyramid Top with Slip Section
MESH SQUARE TOP TERMINATION
F0922 ETO-8DM Square Top with Mesh
MESH SQUARE TOP TERMINATION WITH SLIP SECTION
F0923 ETLO-8DM Square Top with Mesh and Slip Section
STAINLESS STEEL HOOD
Required when installing a vent-free gas log in this fireplace.
F1052 HS36 36" Stainless Steel Hood w/4" Brow
DRAIN PAN
F1089 DP36 Drain Pan
FIRESTOP THIMBLE
F0911 38FST Firestop Thimble ( Use when penetrating a joist)
F0912 FST30 Firestop Thimble ( Use when offsetting through a joist)
LABEL-UL127-50PK WARNING
HOT
• Fire Risk
• Insulation and combustibles must not touch
pipe
• Consult manual for clearance requirements
• Ensure proper connection
WARNING
HOT
• Fire Risk
• Insulation and combustibles must not touch
pipe
• Consult manual for clearance requirements
• Ensure proper connection
WARNING
HOT
• Fire Risk
• Insulation and combustibles must not touch
pipe
• Consult manual for clearance requirements
• Ensure proper connection
900599-01
F2659 LABEL-UL127-
50PK UL127 Venting Label - 50 PK
ACCESSORIES Continued