Supermicro P3TDER Plus User manual

Motherboard Components
Note: Interleaved ECC registered memory type must be installed in pairs: slots 18 + 19 and 20 + 21.
*
33
31
29
34
11 12
30
5
4
2
3
28
27
26
25
23
1
15
14
13
35
19
18
10
32
7
6
8
9
24
22
21
20
16
36
37
38
17
28 JP68
29 Ultra160 LVD SCSI Ch B
30 PCI riser card
31 SW1
32 Floppy connector
33 JP1, JP3 header
34 CPU#2 socket
35 CPU#1 socket
36 JP58
37 JP62
38 JP64
39 RAID port
1System board
2 COM2 header
3JA2, JA4 SCSI termination
4 BIOS chip
5 JP73
6 JP56
7JBT1
8Ultra160 LVD SCSI Ch A
9, 10 IDE #1, IDE#2 connector
11 Chassis fan
12, CPU2 chassis fan
13 CPU1 chassis fan
14 Chassis fan
15 JP65 THRM fan
16 JF1 control panel header
17 JP72
18,19 * Bank 0 memory modules
20, 21 * Bank 1 memory modules
22 Primary power connector
23 Mouse and keyboard ports
24 2 USB ports
25 COM1 header
26 VGA header
27 LAN1, LAN2
39
P3TDER+ Quick Reference
CPU Core/
Bus Ratio**
500-666
555-733
600-800
650-866
700-933
750-1000
800-1064
850-1130
900-1200
950-1260
1000-1330
1050-1400
SW1
#4
ON
ON
OFF
OFF
OFF
OFF
OFF
ON
ON
ON
OFF
ON
SW1
#3
OFF
OFF
ON
ON
ON
ON
OFF
ON
ON
ON
OFF
OFF
SW1
#2
OFF
OFF
ON
ON
OFF
OFF
ON
OFF
OFF
ON
ON
ON
SW1
#1
ON
OFF
ON
OFF
ON
OFF
ON
ON
OFF
OFF
OFF
ON
CPU Core/Bus Ratio Selection
(DIP Switch 1)
Jumpers Description   Default Setting
JA2  LVD SCSI Ch A term. Open (Enabled)
JA4  LVD SCSI Ch B term. Open (Enabled)
JBT1  CMOS clear  Pins 1-2 (Normal)
JP1 FSB speed setting Pins 1-2 (Auto)
JP3 Spread spectrum Open (Disabled)
JP56 Speaker enable/disable Closed (Enabled)
JP58  LAN1 enable/disable Pins 1-2 (Enabled)
JP62  LAN2 enable/disable Pins 1-2 (Enabled)
JP64 SCSI enable/disable Pins 1-2 (Enabled)
JP65 Thermal fan enable/disable Closed (Enabled)
JP68  VGA enable/disable Pins 1-2 (Enabled)
JP72 CPU/CPU chassis fan select Open (Chassis Fan)
JP73  Watchdog enable/disable Open (Disabled)
** Number on left is for 100 MHz FSB speed and number on right
is for 133 MHz FSB speed

To protect the system and components, it is essential that you reinstall the top panel after you have finished working on the system.
Front Panel Functions
1. Hot-plug SCSI hard drive, SCSI ID 0
2. Hot-plug SCSI hard drive, SCSI ID 1
3. 1 slim CD-ROM drive
4. Floppy drive
5. Overheat: Indicates an overheat condition in the system
6. NIC2: Indicates network activity on LAN2 when flashing
7. NIC1: Indicates network activity on LAN1 when flashing
8. HDD: Indicates IDE channel activity
9. Power: Indicates power is being supplied to the system's
power supply units
12
43
56789
Rear Panel Functions
1. AC power connector
2. PS/2 mouse and keyboard port
3. 2 USB ports
4. 2 COM ports ( 1 internal)
5. 1 VGA port
6. 2 x Intel 82550 LAN ports
7. 64/32-bit Expansion slot
8. External Ultra160 SCSI connector
9. PCI card release latch
Due to the fact that adequate air flow and
proper thermal control are very critical in
maintaining 1U system stability and
performance, it is imperative that the proper
installation procedures listed on the left be
followed in order to maximize system
performance.This is especially critical for 1U
Dual Processor Servers with CPU speeds of
1 GHz and above.
Warning !
CPU Heatsink Installation Procedures
(For Supermicro SuperServer 1U Systems)
1) Only those CPU heatsinks that are provided by Supermicro should be used.
2) Apply proper amount of silicon compound on the CPU die.
3) Place the CPU heatsink on top of the CPU.
4) Place the heatsink spring on top of the CPU heatsink and lock the backside of the spring into its notch.
5) Lock the front side of the heatsink spring into its notch.
= >
1 2 3 4 5
Cooling Fan Installation
12
3456
7
8
9