Suptek MD6411 User manual

Unpacking Instructions
Please carefully open the carton and throw away other protections such as
lining and cardboard.
,
Check the parts list to ensure that all component parts are not damaged.
Do not use damaged or defective parts.
Read all instructions carefully before installation.
Important Safety Information
Please be careful when installing and operating the device. Please read this
manual before installation and follow all instructions provided in the text.
Please ask a professional installer or install it with his help if possible.
Do not arbitrarily disassemble parts that are not described in the instructions.
We do not accept damages caused by incorrect installation methods,
including incorrect installation or improper use of this product.
,
Installation instruction MD6411
Step 3 Install the VESA panel on the monitor Step 5 Adjust the angle of the monitor
Fixed on the back of the monitor
Insert the monitor into the head
assembly of the rotating arm
Secure and lock the monitor with screws
Secure the back of the monitor
with the washers Adjust the head of the monitor as needed to prevent it from sagging
Thank you for choosing our products!
qs
r
h
o
d
o
o
o
Step 4 Mount the monitor on the rotating arm
Step 6 Arrange the cable and store the Allen key in the cable lock
We hope you never have the need,but if you do,
our service is friendly and hassle-free.
:716-777-3938
:[e-mail]

(1) Pipe-a (1) Fixture-b (1) Support fixture -c (1) Rotating arm-d
(1) VESA panel -e (3) M5X16 screw -f (2) M8X12 screw -g (1) Nut-h
(1) Keyhole bottom panel - m (1) Clip -n1 (1) Clip -n2 (1) Allen key -o
(1) M10 screw -i (1) Support plate -j (1) M10 gasket -k (1) Spring washer-l
(1) Wrench-p (4) M4X12 screw -q (4) M4X30 screw -r (4) M8 washer-s
CAUTION
WARNING
Fix the monitor bracket and keep it level. If the
bracket is not be fixed, it may fall and damage.
Please make sure the bracket is firmly fixed!
Product Parts List
Option A: Fixture Installation
1.Install the support fixture (c) to the pipe (a).
The pipe (a) is secured with three M5x16 bolts (f) and
with an Allen key (o), see figure 1.
2.The fixture (b) is assembled with the pipe according
to the thickness of the table top. The thickness of the
three locations can vary. Connect with 2 M8x12 bolts (g)
and tighten with an Allen key (o). See figure 2.
figure 2
Option B: Keyhole Mounting
Existing desktop round hole installation
If the existing desktop has a plastic protector, remove it to ensure
a flat surface.
,
1.Mounting base (m)
Tighten the pipe (a) with three M5x16 bolts (f) and an
Allen key (o), see Figure 3.
2.Assemble the pipe (a) and the support plate (j),
the M10 washer (k), the spring washer (I) M10 bolt (i),
and tighten the M10 bolt (i) with a wrench (p),
see Figure 4.
Option B: Keyhole Mounting
Self-drilling ring hole installation
1. Make a 10MM hole on the desktop to install the keyhole
2.Tighten Pipe (a) with 3 M5x16 bolts (f) and an Allen key (o),
see Figure 5.
3.Assemble pipe (a) and support plate (j),
M10 washer (k), spring washer (I) M10 bolt (i).
Tighten the M10 bolt with a wrench (p),
see Figure 6.
Put the rotating arm (d) on the pipe
and tighten with an Allen key (o).
a
m
f
figure 1
figure 3
figure 4
figure 6
figure 5
j
k
l
i
a
m
f
j
k
l
i
a
c
f
g
o
b
Plastic knob
Tool Phillips screwdriver
(3) M5X16 screw -t
o
d
n2
n1
Step 1 Install the pipe to the desktop Step 1 Install the pipe to the desktop
Step 2 Install the swivel arm to the pipe