Sure Heat THE SAVANNAH VFLBS36 Mounting instructions

WHAT TO DO IFYOU SMELL GAS
• Do not try to light any appliance.
• Do not touch any electrical switch; do not use any
phone in your building.
• Immediately call your gas supplier from
a neighbor's phone.Follow the gas
supplier's instructions.
• If you cannot reach your gas supplier, call the fire
department.
Homeowner’s Installation
and Operating Manual
Outdoor Stainless Steel Universal Firebox
model numbers VFLBS36 VFLBS42
Installer: Leave this manual with the appliance.
Consumer: Retain this manual for future reference.
THE SAVANNAH
Outdoor SERIES
If the information in this manual is not
followed exactly, a fire or explosion may result caus-
ing property damage, personal injury or loss of life
Do not store or use gasoline or other
flammable vapors and liquids in the vicinity
of this or any other appliance
Installation and service must be performed
by a qualified installer, service agency
or the gas supplier.
Improper installation, adjustment, alteration, service or
maintenance can cause injury or property damage.
Read the installation, operating and maintenance
instructions thoroughly before installing or servicing
this equipment.
For Outdoor Use Only.

Congratulations!
2
INSTALLER/CONSUMER SAFETY INFORMATION
Read and save these instructions.
This book contains your installation instructions and should be kept in a safe place. For you to realize
all the advantages and use of the reliable service that has been engineered into your Sure Heat
Manufacturing fireplace, you must carefully follow all of the instructions contained in this book regarding
installation and operation of the fireplace.
These instructions should be read carefully in their entirety before beginning installation of
the fireplace.
It is suggested that you wear work gloves and safety glasses to protect your hands and eyes when
installing your fireplace. NOTE: Authorities having jurisdiction (i.e. building inspectors, fire marshals, etc.)
should be consulted before installation to determine the need to obtain a permit.
Table of Contents
Safety Information . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .2-4
Before You Start . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .5
Hearth Dimensions . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .6
Fireplace Framing Dimensions . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .7
Installation Instructions . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .8-14
Locating the Fireplace . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .8
Gas Line . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .8
Clearances . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .9-10
Installing the Firebox. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .11
Finishing the Fireplace . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .12
Weather Protection Doors . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .13
Replacement Parts . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .14
Servicing . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .14
Warranty . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .16
General Installation Information
In planning the installation for the appliance it is necessary to determine
where the unit is to be installed and whether optional accessories are
desired. Gas supply piping should also be planned.The following steps
represent the normal sequence of installation. Each installation is unique,
however, and might require a different sequence.
1. Position firebox prior to framing or into prepared framing.
2. Plumb gas line. (Gas connections should only be performed by an
experienced, licensed/certified tradesman).
3. Install gas log heater per the instructions provided with the heater.
4. Complete finish wall material, surround and optional hearth extension
to your individual taste.
Proposition 65 Warning:
Fuels used in gas,
woodburning or oil fired
appliances, and the
products of combustion
of such fuels, contain
chemicals known to the
State of California
to cause cancer, birth
defects and other
reproductive harm.
California Health &
Safety Code Sec.
25249.6

Safety Information
3
IMPORTANT
Read these instructions carefully before
installing or trying to operate a gas heater in this fire-
box.
This gas appliance should be installed by a
qualified installer in accordance with local building
codes and with current CSA-B149.1 Installation codes
for Gas Burning Appliances and Equipment.
FOR U.S.A Installations follow local codes and/or
the current National Fuel Gas Code.ANSI
Z223.1/NFPA 54.
FOR SAFE INSTALLATION AND
OPERATION PLEASE NOTE
THE FOLLOWING:
1.This appliance gives off high temperatures and
should be located out of high traffic areas and
away from furniture.
2. Children and adults should be alerted to the hazards
of the high surface temperatures of this appliance
and should stay away to avoid burns or ignition of
clothing.
3. Children should be carefully supervised when they
are in the same room as your appliance.
4. Under no circumstances should this appliance be
modified. Parts having to be removed for servicing
should be replaced prior to operating this appli-
ance again.
5. Installation and any repairs to this appliance should
be carried out by a qualified service person. A
professional service person should be contacted
to inspect this appliance annually. Make it a
practice to have all of your gas appliances checked
annually.More frequent cleaning may
be required due to excess lint and dust from
carpeting, bedding material, etc.
6. Control compartments, burners and air passages in
this appliance should be kept clean and free of
dust and lint. Make sure that the gas valve and
pilot light are turned off before you attempt to clean
this unit.
7. Keep the area around your appliance clear of
combustible materials, gasoline and other
flammable vapor and liquids.This appliance should
not be used as a drying rack for clothing, nor
should Christmas stockings or decorations be
hung in the area of it.
8. Under no circumstances should any solid fuels
(wood, coal, paper or cardboard etc.) be used in
this appliance.
9.The flow of combustion and ventilation air must not
be obstructed in any way.
10.Whether the appliance is installed directly on
carpeting, vinyl tile or any combustible material
other than wood, this appliance must be installed
on a metal or wood panel extending the full width
and depth of the appliance.
11.This appliance requires adequate ventilation and
combustion air to operate properly.
• Any change to this heater or its
controls can be dangerous.
• Improper installation or use of the
heater can cause serious injury or
death from fire, burns, explosion or
carbon monoxide poisoning.
PLEASE READ THE FOLLOWING
CAREFULLY
Remove any plastic from trim parts
before turning the fireplace “ON”.
It is normal for fireplaces fabricated of
steel to give off some expansion
and/or contraction noises during the
start up or cool down cycle. Similar
noises are found with your furnace
heat exchanger or car engine.
It is not unusual for your Sure Heat gas
fireplace to give off some odor the first
time it is burned.
This is due to the curing of the paint
and any undetected oil used in the
manufacturing process.
It is recommended that you burn
your fireplace for at least ten (10)
continuous hours the first time you
use it.

Safety Information
4
12. Do not use this appliance if any part has been
under water. Immediately call a qualified service
technician to inspect the appliance and to replace
any part of the control system or gas control that
has been under water.
13. Inspect the burner before each use of the
appliance.The burner must be replaced prior
to operation if there is evidence the burner is
damaged. Use only burner specified by
manufacturer.
LP-cylinder enclosures, if provided by the
consumer must conform to the design parameters as
detailed below.
Enclosures for LP-Gas Supply Systems
The design of the appliance shall be such that
(1) the LP-gas supply cylinder(s) can be connected,
disconnected and the connections inspected and
tested outside the cylinder enclosure; and (2) those
connections which could be disturbed when installing
the cylinder(s) in the enclosure can be leak tested
inside the enclosure.
Description
The VFLBS Series are radiant fireplaces. Do not
burn wood or other materials in these appliances. Each
model is available with standing pilot for use with
Natural or Propane gas units.
Report to your dealer any parts damaged
in shipment.
Adequate combustion and ventilation air must be
provided.The flow of combustion and ventilation air
MUST NOT be obstructed.
Provide adequate clearances around the air
opening into the combustion chamber; and adequate
accessibility clearance for servicing and proper
operation. NEVER obstruct the front opening of the
appliance.
This fireplace is not designed to be water tight.
Therefore,when installing this unit against
an exterior wall, the wall must be finished before
setting unit in place.

Before You Start
5
You have purchased a stainless steel outdoor firebox.This installation manual will enable you to obtain a
safe, efficient and dependable installation of your stainless steel outdoor firebox system.
Do not alter or modify the firebox or its components under any circumstances. Any modifications or alteration
of the firebox system, including but not limited to the firebox and accessories, may void the warranty, listings and
approvals of this system, and could result in an unsafe and potentially dangerous installation.
BeforeYou Start
Carefully inspect the contents for shipping damage. If any parts are missing or damaged, immediately inform
the dealer from whom you purchased the appliance. Do not attempt to install any part of the appliance unless
you have all the parts in good condition.
Make Sure ThatYou Have Received All Parts
Check your packing list to verify that all listed parts have been received.You should have the following:
1. Stainless Steel Outdoor Firebox 3. Installation and Operating Manual
2. Canopy 4. Four (4) sheet metal screws for canopy.
WhatYou Will Need For Installation
Tools
• Phillips screwdriver • Square
• Hammer • Saw and/or sabersaw
• Tee Joint • Electric drill and bits
• Level • Pipe wrench
• Measuring Tape • Piping complying with
local codes
• Pliers •Pipe sealant approved
for use with propane/L.P.G.
(resistant to sulfer compounds)
Building Supplies
• Framing materials
• Wall finishing materials
• Caulking material
(non-combustible)
• Fireplace surround materials
(non-combustible)
Notice:
Illustrations shown in this manual reflect "typical" installations with nominal dimensions and are for design
and framing reference only. Actual installations may vary due to individual design preferences. However,
always maintain minimum clearances to combustible materials and do not violate any specific installation
requirements.

VFLBS 36, VFLBS 42
This unit is cerified to CSA International
No. 4-96 U.S. for Outdoor Gas Fireplaces
Specifications
6
A
B
C
Hearth Dimensions
Fig. 1: Firebox
Internal
Dimensions
MODEL Front Width (Brick to Brick)
A
Back Width
(Back to Brick)
B
Hearth
Depth
C
VFLBS36 33.5"
(851 mm) 20" (507 mm) 17" (432mm)
VFLBS42 39.5"
(1002 mm) 26" (660 mm) 17" (432mm)

Framing Specifications
7
A
C
B
D
FE
K
LH
J
G
P
M
N
P
Q
R
Fig. 2
VFLBS36 VFLBS42
A36" 42"
B30" 30"
C41" 47"
D1.5" 1.5"
E38" 38"
F40.15" 40.15"
G11.35" 11.35"
H20" 20"
J5" 5"
K26" 32"
L21.5" 21.5"
M66.5" 72.5"
N33.25" 36.25"
P47" 51.25"
Q6.5" 6.5"
R1.5" 1.5"

Installation and Instructions
8
Locating the Fireplace
Figure 3 shows some of the many ways your
fireplace may be installed. Consider the traffic pattern
in your outdoor living space and the location of doors
and windows.
Your fireplace weighs no more than some of your
fine furniture. If the fireplace is located near a load
bearing wall, additional supports to the foundation will
not be necessary.
HEAVY FACINGS SUCH AS BRICK, STONE,
ETC., MAY REQUIRE ADDITIONAL FOUNDATION
SUPPORT. ALTHOUGH THIS UNIT MAY BE
INSTALLED ON COMBUSTIBLE SURFACES, IT
MUST NOT BE INSTALLED ON CARPET OR VINYL.
Gas Line Installation
Plumbing connection should only be
performed by a qualified, licensed plumber. Main
gas supply must be off when plumbing gas line to
fireplace or performing service
Consult all local codes.All gas piping must be
installed to comply with local codes, or in the absence
of local codes, with the latest edition of the national
Fuel Gas Code ANSI Z223.1/NFPA54.
The 1⁄2" gas line may enter either from the left side
or the right side of the firebox. Gas access holes are
provided on both sides of the firebox.
Install a 1⁄2" gas line through the hole provided in
the firebox. Outside the firebox, the gas line connects
to a gas shut-off valve recessed flush into the wall or
floor.The valve should be controlled by a removable
valve key for safety.
An ANSI approved manual shut-off valve, union
and plugged 1⁄8" NPT pressure tapping point must be
installed upstream of the heater.
A sediment trap may be upstream of the heater
to prevent moisture and contaminants from passing
through trap to the heater controls and burners.
Failure to do so could prevent the heater from
operating reliably. Consult applicable codes.
Exterior Wall
Flush
Corner
Space Divider
Free Standing
Fig. 3: Locating the Fireplace

Installation and Instructions
9
An external regulator must be used on all
propane/L.P.G. heaters, in addition to the regulator
fitted to the heater, to reduce the supply tank pressure
to 13" w.c. (maximum). Any copper tubing used to
supply propane/L.P.G. from the tank must be
internally tinned.
NOTE: When connecting propane/L.P.G. outdoor
heaters, you must use pipe sealant resistant to
propane/L.P.G.
IMPORTANT: Hold heater regulator with a wrench
to prevent movement when connecting to inlet piping.
Check Gas Type:The gas supply must be the
same as stated on the heater's rating plate. If the gas
supply is different, DO NOT INSTALL THE HEATER.
Contact our dealer for the correct model.
Connecting directly to an unregulated
propane/L.P.G. tank can cause an explosion.
After completing connection, test all gas joints from
the gas meter to the gas heater regulator for leaks.
Using water soap and water solution or a gas sniffer.
DO NOTUSE AN OPEN FLAME.
Do not connect directly to natural gas
1/2 PSI or 2 PSI systems. Always make sure natural
gas pressure is regulated 10.5 w.c.
(maximum before operating unit).
Fireplace Clearances
The fireplace may be placed directly on a
combustible floor, against a combustible wall at marked
clearances or on a raised wooden platform.
If the fireplace is to be installed on a raised
wooden platform, the platform must be a continuous
level surface.The fireplace must be secured in place
so it cannot shift positions.The nailing flanges on the
sides of the firebox make securing it to the framing
easy. They were designed to allow the installation of
wallboard or plywood flush with the face of the
fireplace.
Only the header (Fig. 2, page 7) may rest on the
standoffs on top of the firebox.
When the fireplace is installed over carpeting,
vinyl, tile or any combustible material other than wood
flooring, it must be installed on a metal or wood panel
extending its full width and depth. Alternatively, the
carpeting, vinyl, tile, etc., may be removed from
beneath the fireplace before installing.
COMBUSTIBLE MATERIALS MUST NOT BE
INSTALLED OVER OR TOUCH ANY BLACK PAINTED
SURFACE.

Installation and Instructions
10
A
B
Mantel
Guard
Mantel
Fireplace
Opening
Fig. 4
Fig. 5 Chart
Clearance to Combustible Mantel with Mantel
Guard in place.
Fig. 6
Mantel Depth
(A) 2" 4" 6" 8" 10"
Clearance
Fireplace
Opening (B) 6.5" 10" 13" 17" 22"
Clearances
To ensure a safe installation the following
instructions must be carefully observed.
1. Sidewall Clearances: Clearances from the side of
the fireplace opening to any combustible wall
should not be less that 9".
2. Ceiling Clearances:The ceiling height should
not be less than 42" from the top of the
fireplace opening.
3. Mantel Clearances:
a) Noncombustible materials used in this
installation such as slate, marble, tile, etc. must
comply with local ,state ,national codes and
manufactures specifications. Do not install a
combustible material behind sheet metal.
Failure to use noncombustible materials above
the opening as specified in these instructions
may cause damage to the materials used and
create a fire hazard.
b) A heat reducing mantel guard is shipped with
the fireplace. Use of this mantel guard is
required in order to reduce mantel heights as
shown in figure 5.When the mantel guard is
installed, a combustible mantel piece may
project 2" from the wall at 6" above the
fireplace opening. A 6.5" mantel projection at
13" above the fireplace opening and a 10"
projection at 22" above the opening.
(Fig 4 and 6)
c) If the fireplace has no mantelpiece, then the
heat resistant material must extend upwards a
distance of at least 9" from the fireplace
opening. (Fig. 4)
To install the required mantel guard you will need a
1/4" nut driver or socket.The mantel guard has seven
holes along the top edge.There will already be screws
in three of the holes. Line up slots in Mantel Guard
with holes in the upper channel (top front edge) of the
firebox.The mantel guard will fit tightly in the top front
edge of the fireplace opening. Attach the mantel guard
with the four sheet metal screws provided.
The required firebox canopy
(mantel guard) supplied with this unit from Sure
Heat (the manufacturer) must not be modified or
replaced with a canopy (mantel guard) that/which
may be provide by the manufacture or supplier of
the decorative room heater.
1) Floor Clearances:No clearance is required if the
appliance is installed per these instructions.

Installation and Instructions
11
Installing the Firebox
This list of specific instructions will help you
make certain that every installation operation is done
correctly. Complete the installation steps in the
sequence shown.
LOCAL BUILDING CODES SHOULD BE
CONSULTED IN ALL CASES AS TO THE
PARTICULAR REQUIREMENTS CONCERNING THE
INSTALLATION OF FACTORY BUILT FIREPLACES.
Select the location for the fireplace by taking into
consideration the factors previously outlined in the
Locating the Fireplace section of this manual.
Step 1: Framing the Firebox
The width of the framed openings must be 37"
for 32" models, 41" for 36" models or 47" for 42"
models. (Fig. 2, page 7)
The entire fireplace can be elevated above the
floor to achieve a raised hearth effect.This can be
done by adding a small platform to achieve the
desired height.
Step 2: Install the Firebox
Install the firebox into the framed opening by
setting it directly in front of the opening and
sliding it into the proper position.
Step 3: Level the Firebox
Check the level of the firebox on the top edge of
the fireplace face. Shim if necessary.
Step 4: Secure the Firebox
Four (4) nailing flanges are supplied with the
fireplace to level the box and secure firmly in
place; Bend the nailing flanges from the sides of
the fireplace as shown in Figure 7.
Note:The nailing flanges have two (2) sets of
holes to allow for adjustment for 1/2" or 5/8" offset
of the face of the unit. When installing the nailing
flanges, choose the set of holes on the nailing
flange that fit with your application.
Note:This firebox employs spacers, stand offs
and nailing flanges to inhibit contact of parts of
the firebox with combustible construction .
do not alter the spacers or divert
from their intended use or notch the framing in
any manner.
Step 5: Gas Piping and Connection
The gas piping must be installed in accordance
with local codes or, in the absence of local codes,
in accordance with the National Fuel Gas Code,
ANSI Z223.1/NFPA 54, latest edition.
Piping should be tested for leaks prior to final wall
installation.Test for leaks, using a soap and water
solution or any acceptable solution or mechanical
gas leak detector, after completing the connection.
DO NOT USE OPEN FLAME.
Installation must conform with local
codes, or in the absence of local codes,
with the National Fuel Gas Code,
ANSI Z223.1/NFPA 54.
E
DETAIL E
Fig. 7

Installation and Instructions
12
Step 6: Optional Procedure for
Cold Climate Installations
The insulation and sealing of the enclosure around
the fireplace is very important in cold climates. If
the enclosure is insulated and sealed properly, you
can avoid future cold air problems.The time taken
to install the firebox correctly is well worthwhile.
The following steps are to stop potential cold air
problems. (Do not use Kraft Faced insulation -
paper faced)
Insulation of the Fireplace Enclosure
When in a chase or an outside wall, the fireplace
enclosure should be insulated like any other wall of
your home. Insulation should be installed on the
outside wall(s) and the wall about the fireplace.
(Do not use Kraft Faced insulation - paper faced.)
Insulate to Seal Under the Fireplace
Insulating under the fireplace is beneficial for
installations on a concrete slab in cold weather
climates.The fireplace should be placed on insulating
board. It is important that a hard, rigid surface be main-
tained, so do not use fiberglass insulation for
this purpose.
WHEN INSTALLING A FIREPLACE
IN AN INSULATED ENCLOSURE, BE SURE TO
MAINTAIN ALL MARKED AIR SPACES. DO NOT
USE KRAFT (PAPER FACED) INSULATION .
Seal Seams
Sealing the seams of the fireplace is beneficial for
installations in cold weather climates where the outer
wall meets the bottom pan and the front face. Also
seal between the fireplace and finishing materials.
Use high temperature caulk. Refer to Figure 8 for
details of sealing spaces between the fireplace and
finishing materials.
Finishing the Fireplace
There are a wide variety of finishing materials
available for your fireplace from formal wall treatments
with marble and mantles to rustic wood paneling, stone
or brick.
IT IS IMPORTANT THAT THE BLACK FACE OF
THE FIREPLACE NOT BE COVERED WITH ANY
TYPE OF COMBUSTIBLE MATERIAL.
Noncombustible facing materials such as marble,
brick or ceramic tile may overlap the black face of the
fireplace up to the opening on either side of the
fireplace. Seal all joints between the black fireplace
face and the wall covering with a heat-resistant
material such as rock wool insulation or mortar. Be
sure to use high temperature adhesive or mortar when
anchoring brick, stone or tile to the face of the
fireplace.Check to see whether man-made brick and
stone are made of noncombustible materials before
using them on the face of the fireplace. Some of these
products contain combustible materials. Combustible
wall coverings such as paneling or wallboard may not
overlap the black face of the fireplace.The space
between the wall covering and the fireplace should be
sealed with a heat-resistant material such as rock wool
insulation or mortar.
NOTE: An “L” shaped steel lintel must be installed
across the top of the firebox opening where facing
materials such as brick or stone are used on the face
of the firebox. It acts as a support/firestop. It should be
attached to the face of the fireplace with screws and
sealed to the fireplace with a heat-resistant sealer.
These vent free fireplaces are not to be
used with anyTYPE or MODEL of glass doors.
Fireplace screens must be in the closed
position across the entire hearth opening prior to
the operation of the decorative room heater.
Stand
Off
Caulking or Sealant
Noncombustible
Insulation
Finishing Material
Top View
Side View
Caulking or Sealant
Noncombustible Material
Finishing Material
Insulation
Stud
Fig. 8

Installation and Instructions
13
Weather Protection Doors
Weather Protection Door(s) must
be removed while fireplace, logs and burner
are in use.
Both weather protection doors must be completely
removed from the fireplace before gas logs are place
in use and while logs are burning.
Handles on the outside of doors may
be warm/hot to the touch due to previous fireplace
use or by temperatures created by the sun. It is
suggested for your safety gloves are worn while
removing or replacing the weather protection
doors.
NOTE: Weather protection doors are not water
tight, but are weather resistant.Visual inspection of the
combustion chamber and log set is recommended prior
to each use.
Use and Maintenance
Doors are easily removed by grasping the
provided handles and slightly lifting up, pulling the
doors gently out towards user.
Doors should be stored in a convenient area and
away from the fireplace while unit is in use.
To replace doors it is recommended to wait an
appropriate time until the outside surround and screen
mesh of the fireplace have cooled to at least ambient
air temperature.
To replace weather protection doors, grasp the
handles (gloves recommended) and gently place top
edge under mantle guard and gently push up while
placing the lower edge slots in holding stubs on bottom
of front surround.
NOTE: Doors in the applied position (attached)
purposely overlap on the center vertical edge for better
weather protection.
Weather Protection Doors may be cleaned by
gently wiping the surface with any commercial grade
stainless steel cleaner.
Do not use any cleaners or chemicals
no specifically manufactured for cleaning or
polishing stainless steel finishes.This may result
in damaging the door(s) finish.

Parts and Servicing
14
123 4
56
VFLBS36 VFLBS42
1 Firebrick Left 21361101 21421101
2Firebrick Middle 23361201 23421201
3 Firebrick Right 21361301 21421301
4 Firebrick Bottom 21361401 21421401
5 Screen Mesh Wire 20361301 20421301
6 Mantel Guard 21361401 21421401
7 Screen Mesh 21362001 21422001
Contact Sure Heat Manufacturing for questions
concerning prices and policies covering replacement
parts. Parts may be ordered through your Sure Heat
distributor or dealer.
You will need the correct name, part number
and model number of the appliance when ordering
replacement parts.
Should you need additional information beyond
what your dealer can furnish, contact:
Sure Heat Manufacturing
3130 Moon Station Road
Kennesaw, GA 30144
[phone]
Servicing
Repair and replacement work should only be done
by a qualified service person.
Always shut off the gas supply and make sure
the appliance is cool before beginning any
service operation.
Always check for gas leaks after servicing.
www.sureheat.com
7

Notes
15
____________________________________
____________________________________
____________________________________
____________________________________
____________________________________
____________________________________
____________________________________
____________________________________
____________________________________
____________________________________
____________________________________
____________________________________
____________________________________
____________________________________
____________________________________
____________________________________
____________________________________
____________________________________
____________________________________
____________________________________
____________________________________
____________________________________
____________________________________
____________________________________
____________________________________
____________________________________
____________________________________
____________________________________
____________________________________
____________________________________
____________________________________
____________________________________
____________________________________
____________________________________
____________________________________
____________________________________
____________________________________
____________________________________
____________________________________
____________________________________
____________________________________
____________________________________
____________________________________
____________________________________
____________________________________
____________________________________
____________________________________
____________________________________
____________________________________
____________________________________
____________________________________
____________________________________
____________________________________
____________________________________
____________________________________
____________________________________
____________________________________
____________________________________
____________________________________
____________________________________

16
RMH130-51512001 01/09/2006
If you have other questions, please contact Customer Service Hotline
[phone]
LIMITED LIFETIME WARRANTY
Limited Warranty shall apply to the original purchaser at the original installation point only
The following components are warranted for life to the original owner, subject of proof of purchase: Firebox, Combustion
Chamber, Heat Exchanger.
General Warranty: This Limited Lifetime Warranty will be void if the appliance is not installed by a qualified installer in
accordance with the installation instructions. The Limited Lifetime Warranty will also be void if the appliance is not operat-
ed and maintained according to the operating instructions supplied with the appliance, and does not extend to (1) firebox
assembly damage by accident, neglect, misuse, abuse, alteration, negligence of others, including the installation thereof
by unqualified installers, (2) the costs of removal, reinstallation or transportation of defective parts on the appliance, or (3)
incidental or consequential damage. All service work must be performed by an authorized service representative.
This warranty is expressly in lieu of other warranties, express or implied, including the warranty of the merchantability of
fitness for the purpose and of all other obligations or liabilities. Sure Heat Mfg. Co. does not assume for it any other obli-
gations or liabilities in connection with the sale or use of the appliance. In states that do not allow limitation on how long
an implied warranty lasts, or do not allow exclusion of indirect damage, those limitations of exclusions may not apply to
you. You may also have the additional rights not covered in this Limited Lifetime Warranty.
Sure Heat Mfg. Co. reserves the right to investigate any and all claims against the Limited Lifetime Warranty and decide
upon method of settlement.
All costs for removal and reinstallation are the expressed responsibility of the purchaser.
For repair or replacement of a defective part or parts, contact our customer service department at 1-800-229-5647. You
will be asked to provide valid warranty registration, proof of purchase and model number.
Purchased From: ______________________________________________Date: __________________________
Size: oVFLBS36 oVFLBS42
Name ______________________________________Date: ____________Phone ( ) __________________
Address ____________________________________________________________________________________
City ________________________________________State ____________Zip __________________________
E-mail ______________________________________________________________________________________