Surecom EP-1427X-2 User manual
EP-1427X-2 USB2.0
To Ethernet Adapter
www.surecom-net.com
4311427X2ZZ0
Introduction
SURECOMs EP-1427X-2 USB2.0 To Ethernet Adapter s des gned to connect USB-equ pped a
desktop, notebook, or USB hub to an Ethernet network. It performs the same funct on as trad t onal
Network Interface Cards w thout open ng up the PC and nstall ng the card. A USB-equ pped PC can
s mply connect an Ethernet network w th th s USB2.0 To Ethernet Adapter, users can share f les be-
tween computers, use pr nters and Internet access, send and rece ve e-ma ls, access CD-ROM/backup
dr ve attached to others PCs, etc.
Hot-swapping
The USB2.0 To Ethernet Adapter features hot-swapp ng and doesnt need to shut down and restart
your PC to attach, add, or remove a per pheral. Just plug t n eas ly and go! The PC automat cally
detects the per pheral and conf gures the necessary software. Users of mult -player games, bus ness and
notebook PC users who want to share per pherals all can take the most advantages.
Easy Installation
The USB2.0 To Ethernet Adapter prov des easy-to- nstall steps and dr vers for compat b l ty w th PC
s runn ng the W ndows 98/ME/2000/XP network operat ng system. LEDs on the adapter nd cate the
network and traff c status for s mple troubleshoot ng.
Key Features
1. Compl es w th IEEE802.3 10BASE-T, IEEE802.3u 100BASE-TX Standard and USB Ver.1.0/1.1
2.0
2.A real Plug & Play and no need to open your computer.
3.Easy to connect and USB-equ pped notebook, portable, or desktop computer to any Ethernet local
area network.
4.Compat ble w th W ndows 98/ME/2000/XP.
5.IEEE802.3 10BASE-T and IEEE802.3u 100BASE-TX are compat ble.
6.NO IRQ confl ct hassles.
7.The un t requ res no external power supply; t s powered d rectly by the Un versal Ser al Bus.
Package Contents
One USB2.0 To Ethernet Adapter
One d skette
Technical Specification
Standard: IEEE 802.3 10BASE-T, IEEE 802.3u 100BASE-TX and USB ver.1.0/1.1/2.0
Date Transfer Rate: 10/100Mbps
Memory S ze: 7*16b t
Med a Support: 1 RJ-45 Ethernet connector & 1 USB Cable
LED D splay: 10,100, FDX, Act.
Power: Bus power from USB host controller
Temperature: 0°C~45°C
Hum d ty: 10%~90%
Cert f cat on: FCC Class B, CE Mark Class B.
LED indicators
The LED nd cators nclude Act.,10,100 and FDX.
Act.:Th s LED nd cator w ll l ght up when there s a secure connect on n aUSB2.0 Host Port.
The LED nd cator w ll bl nk when the data s transferred or accepted.
10: The LED l ghts means the EP-1427X s connect ng to dev ce n Ethernet network by
10Mbps transm ss on rate. When LED bl nks, the data s transferr ng by 10Mbps.
100: The LED l ghts means the EP-1427X s connect ng to dev ce n Ethernet network by
100Mbps transm ss on rate. When LED bl nks, the data s transferr ng by 100Mbps.
FDX: When the LED l ghts, the EP-1427X s work ng n Ethernet network by full-duplex mode.
When the LED off, the EP-1427X s work ng n Ethernet network by half-duplex mode.
It cons sts of one RJ-45 and USB Cable.
RJ-45 Port: Th s port s used to connect an Ethernet network.
USB Cable: Th s cable s used to connect USB-equ pped desktop PC / Notebook.
Application:
Connectors
Installation
Step 1.
Plug the USB2.0 To Ethernet Adapter nto
USB connector of PC, W ndows XP prompts
Found New Hardware W zard w ndow.
Cho ce Install from a l st or spec f c locat on
(Advanced) and cl ck Next button.
Step 2.
Insert dr ver d skette to floppy A, and choose
Search removable med a (floppy, CD-ROM),
and cl ck Next button.
Step 3.
Cl ck Cont nue Anyway button n Hardware
Installat on w ndow.
Step 4.
Congratulat ons! The USB to Ethernet
dr ver has been nstalled successfully.
Notices:
Please dont swap cont nually before the host f n shes detect ng when the USB To Ethernet Adapter s
connected to the host or other dev ces; otherw se the system w ll shut down and reboot.
FCC Statement
This device complies with FCC Rules Part 15. Operation is subject to the following two
conditions
1. This device may not cause harmful interference, and
2. This device must accept any interference received, including interference that may cause
undesired operation.
This equipment has been tested and found to comply with the limits for a Class B digital device,
pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection
against harmful interference in a residential installation. This equipment generates, uses and can
radiate radio frequency energy and, if not installed and used in accordance with manufacturers
instructions, may cause harmful interference to radio communications. However, there is no
guarantee that interference will not occur in a particular installation. If this equipment does
cause harmful interference to radio or television reception, which can be determined by turning
the equipment off and on, the user is encouraged to try to correct the interference by one or more
of the following measures
1. Re-orient or relocate the receiving antenna.
2. Increase the separation between the equipment and receiver.
3. Connect the equipment to an outlet on a circuit different from that to which the receiver is
connected.
4. Consult the dealer or an experienced radio/TV technician for help.
WARNING! Any changes or modifications to this product not expressly approved by the manu-
facturer could void any assurances of safety or performance and could result in violation of Part
15 of the FCC Rules.
CE Declaration of conformity
This equipment complies with the requirements relating to electromagnetic compatibility, EN
55022 class B for ITE and EN 50082-1. This meets the essential protection requirements of the
European Council Directive 89/336/EEC on the approximation of the laws of the Member States
relating to electromagnetic compatibility.
Trademarks
All company, brand, and product names are trademarks or registered trademarks of their res-
pective companies.
3-Year Warranty
The manufacturer warrants to the or g nal consumer /purchaser free from defects
n mater als or workmansh p for l m ted t me from the or g nal factory sh pment
date.
KEEP THIS STUB FOR YOUR RECORDS
Date Purchased:
Where Purchased:
From Whom:
Model: Ser al:
MANUFACTURER DISTRIBUTOR
TO:
ATTN:
WARRANTY REGISTRATION CARD
Please complete th s form and return t w th n 10
days of purchase to val date the warranty
Name/T tle:
Company:
Address:
Tel. No.: S gnature:
Purchase Model: Ser al No.:
Purchase from:
Address:
Date of Purchase:
Place
Stamp
Here
Table of contents
Other Surecom Adapter manuals
