2
Warning:to avoid fire or electric shock, do not place the
equipment in rain or humid air.
18）Make sure no water drops inside the equipment. Do
not place an y water holder(eg. Vase)on the equipment.
19）Make sure of at least 6 inch(15.25cm) space above
the euipment for good ventilation and cooling.
20）Attention: For amplifiers mounted in racks, all cables
and materials should keep away from its sides. Before taking
it out from the rack case, please cool it for 2 minutes.
21）Amplifier and speaker system, as well as earphone/headphone
(if provided)can generate high sound pressure level, which may
cause temporary or permanent damage to hearing. Please set the
volume carefully.
22)FCC conformity declaration:this equipment conforms the
classB mathematicsdevice limit in chapter 15 of FCC. The
purpose of the regulation is to provide reasonable protection
against possible dangerous interference during installation in
residence area.This equipment generates , uses and radiates RF
energy. Not following the manual in operation and installation
may have negative interference to radio communication, but we
can not make sure that there is no such interference in special
situation. If we confirm by turning on and off the equipment,
there is indeed interference to radio communication. We suggest
to eliminate it by following measures: adjust the direction or
position of the receiving antenna. Increase the distance between
the equipment and receiver. Connect the equipment to a different
socket from the receiver. For more assistance, please contact the
distributor or experienced radio technician. Remark: FMIC does
not take responsibility for the product modifications which violate
the FCC regulation and/or cause invalidity of the certification.
23）Warning:For safety, products with batteries inside or outside
should not be exposed to high temperature, such as the sun or fire.
Wrong replacement/installation of batteries has the danger of
explosion. Only replace the same or similar batteries suggested
by manual.
24）Attention: unplug the equipment and cool it before touching
or replacing electron tube.
25）Warning: before connecting the line plug to lines, please
make sure it is grounded. Likewise, when disconnecting
grounding, please make sure line plug is disconnected.
26）Equipments with lass 1 structure(3-pin plug grounding)
must connect to MAINS socket with connection protection.
The lightning sign inside the triangle warns
users that there is uninsulated “dangerous
voltage” in the enclosure of the product,
which may cause electric shock to human.
The Exclamation point inside the triangle
warns users to pay attention to the important
instructions for operation and maintenance
attached to the product.
1)Read the manual
2）Keep the manual
3）Pay attention to all warning.
4）Follow all instruction.
5）Do not use the equipment near water.
6）Only clean with dry cloth.
7）Do not block any ventilation hole. Install according to
the manual.
8)Do not install near any heating sources, such as heat
sink, heater, stove, etc.
9）Never compromise the safety features of power plugs
with polarity or grounding. In the plug with polarity, one
pin is wider than the other. In the plug with grounding,
there are 2 pins and another pin for grounding. The wider
grounding pin is designed for safety reason. If our plug
does not fit your socket, please contact electricians to
replace the socket.
10）Protect the power cable from being stepped on or
extruded, especially the plug, socket or cable outlet part.
11）Only use the accessories provided by manufacturer.
12）Only use the troller, brackets, or table suggested
or provided by the manufacturer.
When using troller, please move
carefully to avoid falling off and
hurting anyone.
13)In the case of thunder storm or not using for a long
time, please unplug the equipment.
14）Please ask qualified personal for maintenance of the
equipment, in the cases such as damage, leaking, other
article falling inside,
exposure in rain or humid air, malfunction or falling off, etc.
15）To cut off the equipment from AC power, please pull off the
power plug from the socket.
16）The main power plug of the power supply should be
ready for usage anytime.
Safety Operation Instruction
Important Safety Instruction
