Swann SR11035 User manual

Installation and User Guide
For model: SR11035 (all colours)
Swan Service Helpline
0844 567 9600
Retro Under Counter
Fridge
v1.0
SR11035_IM.indd 1 07/11/2017 11:39

22
Important Safeguards
• Do not connect your appliance
to the electricity supply until all
packing and transit protectors
have been removed.
• Leave to stand upright for at
least 4 hours before switching on
to allow compressor oil to settle
• This fridge/freezer must only be
used for its intended purpose i.e
the storing and freezing of edible
foodstuff.
• Do not dispose of the appliance
on a fire. Your appliance
contains non CFC/HFC natural
substances in the cooling system
and in the insulation, which are
potentially flammable if exposed
to fire. Therefore, take care not
to damage, the cooling circuit
or pipes of the appliance in
transportation and in use. In
case of damage do not expose
the appliance to fire or potential
ignition source and immediately
ventilate the room where the
appliance is situated.
• We suggest you contact your
local authority for disposal
information and facilities available.
• See installation section for
information on suitable location.
• On delivery, check to make
sure that the product is not
damaged and that all the parts
and accessories are in perfect
condition.
• Ensure that the plug remains
readily accessible. Do not use
multiple adaptor or extension
cables
.
• Failure to observe these
instructions may invalidate your
right to free service during the
guarantee period.
• Keep ventilation openings, in the
appliance enclosure or in the built-
in structure, clear of obstruction.
WARNING: Keep ventilation
openings, in the appliance
enclosure or in the built-in
structure, clear of obstruction.
WARNING: Do not use
mechanical devices or other
SR11035_IM.indd 2 07/11/2017 11:39

3
Important Safeguards
means to accelerate the
defrosting process, other than
those recommended by the
manufacturer.
WARNING: Do not damage the
refrigerant circuit.
WARNING: Do not use electrical
appliances inside the food
storage compartments of the
appliance, unless they are of
the type recommended by the
manufacturer.
• We suggest you keep these
instructions in a safe place for
easy reference.
• This appliance is not intended for
use by persons (including children)
with reduced physical, sensory
or mental capabilities, or lack of
experience and knowledge, unless
they have been given supervision
or instruction concerning use
of the appliance by a person
responsible for their safety.
• If the supply cord is damaged,
it must be replaced by the
manufacturer, its service agent
or similarly qualified persons in
order to avoid a hazard.
• The plug must be accessible
after the installation.
• Children should be supervised
to ensure that they do not play
with the appliance.
CAUTION: In order to avoid
a hazard due to inadvertent
resetting of the thermal cutout,
this appliance must not be
supplied through an external
switching device, such as a
timer, or connected to a circuit
that is regularly switched on and
off by the utility company
This appliance should only
be connected to an earthed,
switched mains socket. Do not
use an extension cord with this
appliance
SR11035_IM.indd 3 07/11/2017 11:39

4
Your Refrigerator
Refrigerator shelf
Ice box
Thermostat & bulb
Vegetable & salad
crisper drawers
CHANGING THE BULB
The LED lamp is designed for many thousands of hours use. It must be changed by
qualified personnel only
Dairy and multi-
purpose guards
Bottle shelf
SR11035_IM.indd 4 07/11/2017 11:39

5
Installation Notes
1. The appliance should not be tilted more than 45 degrees when you move it. Do
not use force on any part such as the condenser, the door or handle. They could dis-
tort and affect the operation of the refrigerator. Ensure ALL packaging is removed
before installation
2. Make sure there is enough ventilation space around refrigerator.
3. The appliance should not be installed near external heat sources eg direct sun-
shine - or external moisture sources.
It is important that upon receipt you stand your appliance upright for at least 4
hours before switching on to allow the system to settle. Please note that the door
cannot be reversed on this product.
2cm
2cm
2cm
2cm
SR11035_IM.indd 5 07/11/2017 11:39

6
Installation Notes
1. Remove the two screws to the rear of the refrigerator, then the three screws
from the front underside.
If the refrigerator is to be installed in an under counter position, the top cover will
most likely need to be removed. Proceed as follows:
Under Counter Installation
4. Ensure the supply voltage of scoket is same as rating label.
5. The plug must be properly inserted to the wall socket.
6. The mains supply socked must be earthed - preferably with a switch. If it is not
earthed, do NOT install this appliance there. Do not use an extension cord
7. The product is equipped with adjustable feet. Once the product is in place, adjust
these to ensure the fridge is level and doesn’t rock.
DO NOT SITE THE PRODUCT WHERE THE AMBIENT TEMPERATURE IS LIKELY TO
DROP BELOW 5 DEGREES CENTIGRADE - EG: GARAGE OR SHED
SR11035_IM.indd 6 07/11/2017 11:39

7
2. Carefully pry the top panel free
as shown here, taking care not to
damage it.
Under Counter Installation
3. Remove the lid bracket (A). Fit
the upper hinge fitting (B) Fit the
decorative part (C provided) as shown
here.
Notes : The height of the fridge is around 86 cm after removal of the top panel.
Please store the removed top and screws in a safe place in case they are needed
again in the future.
A
B
C
SR11035_IM.indd 7 07/11/2017 11:39

8
Refitting the Top Panel
Re-fitting the top panel is a reversal of the removal procedure.
1. Remove the decorative parts
2. Refit the lid panel and refit the screws
NOTE: The top of the refrigerator is not designed to take heavy weight. Please do
not put heavy items on top of the refrigerator.
First Time Use
1. It is important that upon receipt you stand your appliance upright for at least 4
hours before switching on to allow the system to settle
2. When using the refrigerator for the first time, set the thermostat inside the
refrigerator to 5 without any food inside. When the refrigerator starts, you will hear
the quiet hum of the compressor. You may also hear the circulation of liquids and
gases in the refrigeration system. This is normal on first start up, Generally it will
take 2-3 hours for the appliance to reach temperature. Once temperature has been
reached then put the food inside.
3. The temperature of the refrigerator can be adjusted by rotating the disc of the
thermostat. The higher the value on the setting of the thermostat, the maximum
value of refrigeration (coldest being 7 ). Typically a medium setting of 4-5 is best for
most circumstances.
4. Do not put too much food in the refrigerator. Avoid opening the doors too fre-
quently as this will waste energy and can cause excessive frost build-up.
SR11035_IM.indd 8 07/11/2017 11:39

9
Food Storage Tips
Dairy and muliti-purpose Guard
• Store fatty foods, like butter and cheese.
• Store small, packed foods, like milk, yogurt and beverages.
Refrigerator compartment: 1°C to 5°C
This is the area where the food should be stored to be kept cold/chilled:
• Note: raw and uncooked foods should always be wrapped
• pre-cooked chilled foods, such as ready meals, meat pies, soft cheeses.
• pre-cooked meats such as beef and ham,
• prepared salads (including pre-washed salad greens, rice, potato salad mixed cut and pre
packaged, etc.).
• desserts, such as fresh cheese, cakes, homemade products, and leftovers
Vegetable Drawer/Crisper
• This is the part of the refrigerator has higher humidity.
• Vegetables, fruit, fresh salads, unwashed lettuce, tomatoes, and radishes should be stored
in this compartment.
Wire Wine Rack
• For storing bottled liquids. Always ensure lids are air tight and sealed properly.
Notes:
• Always place raw meat, fish and poultry on the lowest shelf of the refrigerator.
• Ensure that food is well-wrapped or covered before it is stored. This will prevent food from
dehydrating, deteriorating in colour or losing flavour and will help maintain freshness. It will
also prevent cross-flavouring.
SR11035_IM.indd 9 07/11/2017 11:39

10
Cleaning & Maintenance
DAILY CLEANING
The outside of your refrigerator can be
cleaned using a soft cloth moistened with a
mild detergent solution. Wipe dry with kitchen
towel.
Do not use chemical or abrasive cleaners
on any part of your refrigerator as these
could permanently damage or discolour the
surfaces.
INTERNAL CLEANING
Wipe up any internal spills immediately with
a soft cloth moistened with a mild detergent
solution. Dry thoroughly.
SHELVES AND GUARDS
The Dairy guards, and shelves can be re-
moved and cleaned separately. However, we
don’t recommend cleaning the transparent
plastic parts in a dishwasher because the
high temperatures can dull the plastic over
time.
DOOR SEALS
Ensure that the door seals are kept free from
debris at all times. If they don’t seal properly
this can waste energy and cause excessive
ice build-up
DRAIN HOLE AND CLEANING TOOL
There is a small drain hole at the back of the
refrigerator cabinet. There is also a small
cleaning tool in the hole. Use the tool to clear
the drain hole when necessary. Do not allow
foodstuff to clog this hole
PERIODIC MAINTENANCE
From time to time, it may be necessary to
perform more extensive cleaning to keep your
refrigerator in top condition and to maintain
energy efficiency.
Before performing any of these mainte-
nance steps, switch off your refrigerator and
remove the plug from the mains socket. Allow
the freezer section to defrost thoroughly.
EVAPORATOR TRAY
At the other side of the drain hole in the
refrigerator cabinet, there is a small plastic
tray that sits on top of the compressor. This
should be removed and cleaned thoroughly
from time to time to prevent unpleasant
odours.
Take care when moving the refrigerator not
to damage the cooling matrix or tilt the appli-
ance more than 45 degrees.
After maintenance, replace any shelves etc
and reconnect the appliance to the mains
supply.
SR11035_IM.indd 10 07/11/2017 11:39

11
Troubleshooting
1. If the refrigerator does not run:
Check the supply voltage is available at the socket and check that the power plug is
correctly connected.
2. If the refrigerator does not become cold enough:
a. is the thermostat is set too low? (setting 1 is warmest setting 7 is coldest)
b. is there enough space around the refrigerator?
c. is the door is opened too frequently or not closed properly? (check seals).
d. is there direct sun shine on the appliance or are there heat sources nearby?
e. is there too much food inside the compartment?
f. is there dust and debris built up on cooling matrix or compressor?
3. Food is freezing or too cold in refrigerator compartment:
a. There is too little food in the refrigerator
b. Thermostat is set too high
4. If the refrigerator operates noisily:
a. Check that the appliance is installed on a stable, level floor. Adjust the feet if nec-
essary. The refrigerator is too near the wall
b. The food stored in the refrigerator is not touching - particularly applies to bottles.
The refrigerator creates very slight vibrations, which can be amplified greatly with
touching bottles!
Note:
During high relative humidity environment, condensation may occur on the surface
of the refrigerator. This is not a malfunction. Simply clean the surface of condensa-
tion.
If the refrigerator is not working properly after all these checks, contact the service
centre without further delay.
SR11035_IM.indd 11 07/11/2017 11:39

12
Service and Spares
If you experience any problems at all with your refrigerator or require spare parts,
expert help is just a phone call away!
0844 567 9600
You will need to quote the model and serial number of your appliance. This is printed
on the service label just inside the door under the thermostat.
Specifications
Total Net capacity:
Energy A+
Includes:
1 x Salad Crisper
1 x Ice box
2 x Refrigerator shelves
2 x Dairy & multi-purpose guards
1 x Bottle rack
Dimensions:
Climate class:
SR11035_IM.indd 12 07/11/2017 11:39

13
WEEE Directive
Disposal of Unit
Disposal instructions for Swan items in accordance with the WEEE directive. Appliances
bearing the symbol shown here may not be disposed of in domestic rubbish. You are required
to dispose of old electrical and electronic appliances like this separately. Please visit www.
recyclemore.co.uk, or www.recyclenow.co.uk for access to information about the recycling
of electrical items. The WEEE directive, introduced in August 2006, states that all electrical
items must be recycled, rather than taken to landfill. Please arrange to take this appliance to
your local Civic Amenity site for recycling, once it has reached the end of its life.
BS Plug Wiring
The wires in the mains lead are coloured in accordance with the following code:
BLUE NEUTRAL
BROWN LIVE
GREEN/YELLOW EARTH
As the colours of the wire in the mains lead of this appliance may not correspond with the colour markings
identifying the terminals on your plug, proceed as follows:
The wire which is coloured BLUE must be connected to the terminal which is marked with the letter N or
coloured black. The wire which is coloured BROWN must be connected to the terminal which is marked
with the letter L or coloured red. The wire which is coloured GREEN/YELLOW must be connected to the
terminal which is marked with the letter E or (earth symbol) and is coloured GREEN or GREEN/YELLOW.
WARNING: THIS APPLIANCE MUST BE EARTHED
SR11035_IM.indd 13 07/11/2017 11:39

14
Warranty
Notes:
This product is guaranteed for one year from the date of original purchase. If any defect arises
due to faulty materials of workmanship the faulty product will be repaired, refunded or replaced
at our discretion.
The following conditions apply:
The product must have been purchased from new. Proof of purchase will be required
The product must be installed and used in accordance with the instructions contained in this
instruction guide. It must be used only for household and similar purposes such as:
• staff kitchen areas in shops, offices and other working environments;
• farm houses and by clients in hotels, motels and other residential type environments;
• bed and breakfast type environments;
• catering and similar non-retail applications.
The appliance has not been altered, serviced, dismantled or otherwise interfered with by any
person not authorised by Swan.
Any repair work must be undertaken by us or our appointed agent.
Any parts removed during repair work or any appliance that is replaced becomes our property.
It does not cover wear and tear, damage, misuse or consumable parts. Swan Products Ltd
has no liability for incidental or consequential loss or damage. Food value is NOT covered by
the warranty.
This guarantee is valid in the UK and Eire Only.
SR11035_IM.indd 14 07/11/2017 11:39

15
Swan Brand Heritage
Did you know...
Components for the Swan Teasmade
were still being made at the original
Bullpitt & Sons factory on Camden St,
Birmingham as recently as 2006.
Camden St, Birmingham
Please visit our website at:
www.swan-brand.co.uk
For more information and history of the Swan Brand
SR11035_IM.indd 15 07/11/2017 11:39

www.swan-brand.co.uk
Copyright © 2012
Swan Products Ltd. PO Box 3117, Stoke-on-Trent ST4 9GD
Est.1931
We love
what we do
s
2year
GUARANTEE
we’re proud
of our quality
Scan this QR code
to hear about
our story
Find us on Facebook
*
* on selected lines
SR11035_IM.indd 16 07/11/2017 11:39