Sweatband Hydro 10 User manual

Adult Stand Up Paddle Board 10FT
Warning: Please read all instructions carefully before using this product.
Incorrect operation may cause injuries to health.
Instruction Manual
Version 1.0a
1

2Adult Stand Up Paddle Board Instruction Manual
Warning: A Personal Flotation Device (PFD) is required for each user!
Warning: Do not dive or jump!
Warning: Do not use around sharp objects!
• Always wear a buoyancy aid.
• Always let people know where you are going.
• Always carry a mobile phone.
• Always check the weather forecast.
• Always research your paddling spot.
• Always check for leaks in your SUP before going on the water.
• Always check your board and equipment before entering the water.
• Don’t use in white water. Don’t use in breaking waves.
• Don’t use in offshore current. Don’t use in offshore wind.
• The design working pressure is 15psi (1.0bar). the Maximum inated air pressure is 12psi.
• Don’t inate the board with electric power high pressure pump. Don’t over inate the board.
• Adult use only. Not suitable for children under 14years.
• Always wear your board leash while using.
• If the ns become bend, heat the ns rst by placing in a boiling water or using a hairdryer for a few
minutes, then bending them back to its position.
General Safety Precaution
Safety symbol

3
• 1 x Stand up paddle board
• 1 x Aluminium adjustable oar
• 1 x Hand-operated pump with pressure gauge
• 1 x Valve wrench
• 2 x Repair patch
• 1 x Fin
• 1 x Carry bag
Product Structure Terminology
Adult Stand Up Paddle Board Instruction Manual
Contents

4Adult Stand Up Paddle Board Instruction Manual
Setting Up Your SUP
1. Valve operation
2. Inating the board
3. Deating the board
The ination valve is located nearby the tail of the board. Screw out the lid with valve
wrench, then the center valve pin is appeared. It can close/open the valve by pressing it
once and again.
a. Unscrew the valve cap and press down on the pin to open the valve. Let the air ow
naturally into the product, then press down on the pin again to close the valve (in the
UP position).
b. Make sure the pump hose is connected to the ‘inate’ outlet.
c. Attach the pump hose clockwise onto the valve.
d. Start pumping air into the board by sliding the piston up and down till the board is fully
inated.
e. After ination, screw the valve cap and tighten it with valve wrench.
To deate the board, screw out the valve lid, press the valve pin to let it is in the open po-
sition.please be careful of any sand or debris around the valve area when deating as the
small particles could become airborne together with the release of the air pressure.

5
Adult Stand Up Paddle Board Instruction Manual
Fin Installation Instructions
Paddle Installation Instructions
The ination valve is located nearby the tail of the board. Screw out the lid with valve
wrench, then the center valve pin is appeared. It can close/open the valve by pressing it
once and again.
The board paddle comes in three pieces. To build the paddle, hold the button in while
sliding the pieces together until they click into place. The top section of the paddle is
adjustable. Close the button after adjusted the
length to your desired position. Please refer to below images.
Note:
1). After closing the button, if the adjustable section is a little loose, tighten the screw
properly with a screwdriver.
2). The length of the paddle can be adjusted from 170cm to 210cm.

6Adult Stand Up Paddle Board Instruction Manual
Repair Instructions
Care & Storage Instructions
Contact Info
Note: If you nd a chamber is damaged, use the provided repair patch.
1. To nd out the damaged place on the board, wipe the hull with soap and water,the
soap will bubble over the damaged hole.
2. Deate the board completely, clean and dry the damaged area.
3. Cut a piece of suitable size from the repair patch.
4. Apply the vinyl repair glue sparingly to patch, spreading out it evenly all over, then
cover to the damaged area and smooth out any air bubbles.
5. Place a weight on the repaired area, and allow at least 24 hours to reach full bond
strength before inating it.
Note: Vinyl repair glue is not included.
1. After deation completely, use a damp cloth to clean all the surface.
2. Don’t use solvents or other chemicals that may damage the product.
3. Put all the parts in the carry bag after dried completely.
4. Store in a cool & dry place and out of children’s reach.
5. Check the product for damage at the beginning of each season and at regular
intervals when in use.
Should you require any assistance regarding this product please contact us using the
details below:
Address:
Unit 5 – Mill Square,
Featherstone Road,
Wolverton Mill,
Milton Keynes
MK12 5ZD
Email: [e-mail]
Website: www.sweatband.com

7
Adult Stand Up Paddle Board Instruction Manual
Notes: