Swedstyle Space User manual

Operating manual
Electrical Sit & Stand desk
1. IMPORTANT SAFETY INSTRUCTIONS
2. MAXIMUM WIDESPREAD LOAD
3. PRODUCT LABEL
4. MAINTENANCE INFORMATION
5. GETTING STARTED
6. DECLARATION OF CONFORMITY
7. FAULT FINDING
Read the operating manual carefully before operating
the product and retain for reference purposes.
1 - column frame
2 - column frame
3 - column frame
Contact information regarding:
Manufacturer, retailer, phone number:
see product labels on the frame.
B006-02

Read all instructions before using
DANGER.
1. IMPORTANT SAFETY INSTRUCTIONS
This furnishing has been investigated and found suitable for public occupan-
cies and household use.
When using an electrical furnishing, basic precautions should always be fol-
lowed, including the following:
WARNING–To reduce the risk of burns, re, electricshock, or injury to
persons:
1. Always unplug this product from the electrical outlet before cleaning.
2. Unplug from outlet before putting on or taking off parts.
3. Close supervision is necessary when this product is used/operated by, or
near children, invalids or disabled persons.
4. Use this product only for its intended use as described in these instructions.
Do not use attachments not recommended by the manufacturer.
5. Never operate this product if it has a damaged cord or plug, if it is not wor-
king properly.
6. Keep the cord away from heated surfaces.
7. Never drop or insert any object into any opening.
8. Do not use outdoors.
9. To disconnect, remove plug from outlet.
WARNING:
No one should under no circumstances be underneath the table top whilst the
product is being operated(connected to power). If the product has to be servi-
ced/repaired, the powercord must be disconnected from the power outlet before
anyone is allowed to be underneath the table top.
2. MAXIMUM WIDESPREAD LOAD
Note! The below gures are with the table top included.
1 Column frame60Kg
2 Column frame120Kg
3 Column frame140Kg
Built in overload protection
This product has a built in overload protection. The reason for this is to prevent
mechanical parts from being damaged - if activated - the height of the frame is
adjusted 25mm in the opposite direction.
Built in temperature and duty cycle protection
Duty cycle, max: 1min / 9min
The built in protection can be initiated If used with higher frequency - wait a short
while and try again.

Manufactured by:
Swedstyle AB Vaggeryd, Sweden
Provided by: XXXXX
Model:XXXXXX
CE label with S/N
S/N: 123450-1 Manufactured:20XX
4. MAINTENANCE INFORMATION
Maintenance: The desk, with its integral electronic components is designed to be
completely maintenance free. There is no need for any intermittent lubrication,
adjustment or any subsequent maintenance for the lifetime of the desk. Inter-
fering with the electronics, motor, transformer or frame will make the warranty
to become unvalid.
Caution!
Position electrical cords in such a way that they not can be damaged while the
product either is in use or not in use.
Cleaning
Cleaning of this product should only be carried out with means of a dry cloth.
3. PRODUCT LABEL
The product label Fig1 is located on the frame, see Fig2.
Fig1
Fig2

CAUTION
Ensure there are no obstructions to the movement of the furnishing.•
All cable management should be sufcient to allow manoeuvrability
of the frame through its entire working range.
Upon successful assembly ofthe desk, position the desk in itsnal •
location and level the top using the levelling foot screwson each leg.
Always ensure that no obstructions have been placed under, above or•
adjacent to the furnishing.
A clearance of 50mm surrounding the furnishing is recommended .•
Upon successful assembling of the desk, it is vital that•
the desk is reseted manually before use. See below:•
Reset procedure
Lower the frame to its lowest position by pressing the down arrow on the
hand control. Release the button. Press the button again and keep it pressed
for 10seconds.
Note!
If any of the motor cables have been disconnected while the product is connected
to power, the reset procedure must be carried out.
5. GETTING STARTED
Read the following instructions carefully. The user should be fully aware and
conversant in the operation, function and use of the desks. Each user should
be compliant with the safety regulations concerned with the operation, function
and use of the desks.

6. DECLARATION OF CONFORMITY

7. FAULT FINDING
If you should experience any difculty with this product, please carry out the fol-
lowing initial tests before contacting your local service partner/retailer:
1 Ensure the power source to the desk is functioning properly. Try
connecting the desk to an alternate power source.
2 Ensure all plugs, leads and connectors between the motor, trans-
former and hand control are properly connected.
3 Ensure there are no obstructions or damages to any of the cords.
4 Ensure that the product not is overloaded, and that the load is
evenly spread.
5 If any of the motor cables have been disconnected while the
product is connected to power, the reset procedure must be carried
out. See point 6 below.
6 Lower the frame to its lowest position by pressing the down
arrow on the hand control. Release the button. Press the
button again and keep it pressed for 10seconds.
7 If the problem remains – contact your local retailer.
Please note the serial number of the product. This number
is to be found on the product label wich is located on the frame.
See page 3 Fig1 in this document.

SWEDSTYLE AB Tel. [phone]
Box 171 Fax [phone]
SE-567 24 Vaggeryd [email protected]
Sweden www.swedstyle.se