SY-SUMBOY ZX-P-IV-D-GL80 User manual

Dual Light Pod
ZX-P-IV-D-GL80
Shenyang Sumboy Intelligent Imaging Technology Co.,Ltd.
January 2019

Contents
1 Introduction........................................................................................................................................................................1
2 Product Structure and Electrical Interface...................................................................................................................... 1
2.1 Size of Product........................................................................................................................................................ 1
2.2 Electrical Interface..................................................................................................................................................2
2.3 Connection diagram............................................................................................................................................... 3
3 Product and accessories.................................................................................................................................................... 4
4 Operation instruction of software.................................................................................................................................... 5
4.1 Home........................................................................................................................................................................5
4.2 Operating process...................................................................................................................................................5
5 Precautions......................................................................................................................................................................... 8

1
Dual Light Pod Manual
1 Introduction
Model of ZX-P-IV-D-GL80 ，the pod uses 10X optical zoom camera and un-cooled infrared
camera, and achieves high definition image quality, excellent auto-focus performance as well as
function of target tracking. With the two-axis and two-frame system, the product arrives at higher
precision in image stabilization and no over-top dead zone. The pod is small in size, light in weight
and low in power consumption. It can be used on different types of civil UAVs such as fixed wing,
single rotor and multi-rotor for a wide variety of applications such as investigation, anti-terrorism,
surveillance and pipeline inspection etc.
2 Product Structure and Electrical Interface
2.1 Size of Product

2
2.2 Electrical Interface
2.2.1 External Interface
1) Power interface: 10-16V;
2) 1 way RS232, asynchronous serial interface, 8 data bits, 1stop bit, no parity, baud rate 115200bps;
3) Network/Synchronization 422 compressed video interface;
4) Default card1.
2.2.2 Interface Definition
J30-15 connection interface definition
No.
Interface
Remarks
1
VCC
10V~16V
2
VCC
3
GND
4
GND
5
RS232-TX1
Control serial port
6
RS232-RX1
7
RS232-TX2
Backup serial port
8
RS232-RX2
9
D1-P/Clk-P
Network port and synchronization 422
interface (optional)
10
D1-N/Clk-N
11
D0-P/Data-P
12
D0-N/Data-N
13
SBUS-5V
Debugging SBUS
14
SBUS-RX
15
GND

3
2.3 Connection diagram

4
3 Product and accessories
1）ZX-P-IV-D-GL80 Pod: 1 set;
2）J30-15 connecting line: 1 piece.
ZX-P-IV-D-GL pod + video processing module×1
J30-15 connecting line×1
Please plug in the power finally to prevent damage to the machine.
Please pay special attention to the position of the socket pins.

5
4 Operation instruction of software
4.1 Home
4.2 Operating process
Power on
1. Connect the video source and control serial port to the computer;
2.Open the software.
Confirm port number and network port settings
Right click on the computer, select
computer property as shown on the right;
Under normal circumstances, the selected
serial port number is the refreshed serial
port number after the connection is
inserted.

6
Double click the port(COM and LPT),the
refreshed USB port is which need to be
selected.
Click drop-down list of serial port, select the
right serial port number(status: turned
on;the connection is correct)
Choose the video source:
1. If you access the video through USB
capture card, you can select the USB video,
skip the next step and open the video
directly.
2.If you access the video through the
network port, please follow the next step.
1. Click the button of “network video”;
2. Open the “control panel”and then
“network and sharing center”;
3. Click the icon of “local
connection”→“Property”,double click
“Internet protocol version 4(TCP/IPv4)”;
4. Set the IP address to be on the same
network as the video stream; the address
is ：rstp://192.168.2.119/554;
5. Click the button of “open the video”,the
video are shown on the right.
Common control of the pod
Control the rotation direction of the pod
through the button of up/down/left/right
on the interface;
Select the rotation speed of the pod
through the speed bar;
Home position: the pod is reset;
Motor Off: the switch of controlling the
motor;
Follow Mode: the azimuth axis of the pod
rotates with the aircraft;
Follow disable: the azimuth axis of the pod
stop rotating with the aircraft;
Turn to the angle: set the pod to rotate to
the specified angle.

7
Track: double-click the left button of the
mouse in the video stream to select the
tracking target to realize the function, click
the “stop track”button to cancel tracking;
Click the “track”button to center the cross
cursor;
Template size: the size of the tracking frame
template can be adjusted by the template
size.
Image display settings:
There are four display modes: IR, visible,
and two switchable modes of “visible+IR”.
Zoom, focus, and brightness settings can be
made for visible and IR camera respectively.
Supports for picture storing(Photograph),
video recording(Start Record) and
defogging(Defog ON).
Parameter setting interface is used for debugging, no need to change
Joystick setting
1. Connect the joystick device via USB;
2. The sensitivity of the joystick can be
adjusted;
3. The function of the joystick: the direction
can be reversed in the azimuth and pitch
direction; the cursor sensitivity can also be
adjusted as needed;
4. Button function: the buttons on the
joystick can be set to the corresponding
functions, so as to better control the pod
through the joystick.

8
5 Precautions
1) The daily maintenance of the operating personnel is limited to the replacement or inspection of cables,
daily cleaning and maintenance, and functional inspection to ensure that the instrument is in good technical
condition.
2) Do not open the case without authorization. There are no user-serviceable parts inside the machine.
When the system fails, the fault is located by the manufacturer's technology and then processed.
3) If the product is stored for a long time or does not work, it should be stored in a cool and dry environment.
4) Pay attention to the alignment before inserting the user interface connector. Do not pull the cable directly
when plugging or unplugging the plug.
5) When the product is shipped, all parameters have been debugged. Unless otherwise specified, please use
the recommended configuration parameters.
6) If the product is used on an aircraft, the overall performance is affected by the weight of the aircraft, the
power system, the flight control system, and the user settings.The user needs to have certain professional
capabilities to make the product meet the performance standards approved by the user before using it in the
field.
7) Do not point the camera lens directly at the sun in any state.
8) Disassemble the SD card under the state that the system is powered off.
9) Ensure the lenses are clean and tidy.
10) The first four seconds are the time of automatic calibration gyroscope, please keep the pod stability, or
the system will start last data. You can restart the pod or send instruction of calibration gyro for any drift.
11) The control software need to be running at 64-bit system computer.
Document modification record
Version No.
Modified content
Date
V1.0
First file
2019.01.15
V1.1
Added operation instruction of software
and modified structure diagram
2019.03.14