System air SAVE VTR 250/B User manual

Document in original language | 211891 · A001
SAVE VTR 250/B ceiling mounting kit
Installation instructions GB

211891 | A001

211891 | A001
Contents
1 Warnings.......................................................1
2 Included screws and washers.............................1
3 Dimensions (mm)............................................1
4 Installation options ..........................................2
4.1 Fitting with battens.................................2
4.2 Fitting to concrete with threaded rods
(accessory, art. no. 134014) .....................3
4.3 Fitting with anti-vibration mount
(accessory, art. no. 134009) .....................4
5 Mounting the unit............................................5

Warnings |1
1 Warnings
Warning
• Consider the unit weight when mounting!
Important
• Beware of sharp edges during mounting and maintenance. Use protective gloves.
• This product must only be operated by a person which has suitable knowledge or education within this
field or carried out with the supervision of a suitably qualified person.
• If cooker hood option is not used, cover the cooker hood duct with an outside fitting end cap.
2 Included screws and washers
8x Hexagon head tapping screw
(5,5 x 38) 8x M6 washer
10x M5 washer 10x M5
3 Dimensions (mm)
211891 | A001

2| Installation options
4 Installation options
4.1 Fitting with battens
2x Batten (minimum 45 x 45 mm)
Battens (E) should be tightened to the
ceiling mounting kit from inside. Battens
can be attached from the front and the
rear or from both sides with added self-
tapping screws (A) and washers (B).
Tighten battens with a ceiling
mounting kit to the main ceiling.
These screws are not included.
Choose them based on your ceiling
structure.
Leave at least a 4 mm gap
between ceiling mounting kit and
false ceiling to prevent vibration
noises.
211891 | A001

Installation options | 3
4.2 Fitting to concrete with threaded rods (accessory, art. no. 134014)
4x Drop-in anchor M10 (12 mm x 32 mm)
4x Threaded rod M10 (1 m)
8x Hex flange nut M10
Use a 12 mm drill to make 4 holes in the ceiling with
a depth of 40 mm. Distance between holes is shown
in dimensions drawing. Install drop-in anchors (1)
and attach threaded rods (2). Use hex flange nuts (3)
to mount ceiling mounting kit on threaded rods.
Leave at least a 4 mm gap between ceiling
mounting kit and false ceiling to prevent
vibration noises.
211891 | A001

4| Installation options
4.3 Fitting with anti-vibration mount (accessory, art. no. 134009)
2x Anti-vibration bracket
8x Hex bolt M6 x 12
8x M6 washer
8x Hex nut M6
Anti-vibration brackets (1) should be tightened to the ceiling mounting kit from the front and the rear or from both sides
with added hex bolts (2) then tightened with washers (3) and hex nuts (4) as shown in the illustration.
Tighten anti-vibration brackets with the
ceiling mounting kit to the main ceiling.
Choose screws based on your ceiling
structure. Included screws (A) can be used.
Leave at least a 4 mm gap between ceiling
mounting kit and false ceiling to prevent
vibration noises.
211891 | A001

Mounting the unit | 5
5 Mounting the unit
Important
If cooker hood option is not used, cover the cooker hood duct with an outside fitting end cap.
Remove screw (1) and washer (2) then
pull a lock mechanism to detach side
bracket. Repeat this step for the other
bracket.
Keep removed screws and washers for
later use as they will be needed to
tighten lock mechanisms back.
Loosen ten M5 screws (1) on both sides of the
unit. Attach side brackets (2) that came with
ceiling mounting kit and secure them with the
same screws (1) and M5 washers (C) that are
included in the accessory.
Spare M5 screws (D) are also included in the
accessory if needed.
211891 | A001

6| Mounting the unit
Warning
Consider the weight of the unit when
mounting!
Before lifting and hanging the unit make sure that all
accessories are installed and cables are lead through
the holes on top of ceiling mount kit for easy
connection to the connection box which is located on
top of the unit.
Lift the unit and press it to the ceiling mounting kit.
Lock hooks (X) should go
through holes in
brackets. Pull out the
lock mechanism (Y) if
needed.
Tighten the locking
mechanism on both
sides using previously
removed M4 screws (1)
and washers (2).
211891 | A001

211891 | A001

SAVE VTR 250/B ceiling mounting kit · Installation instructions · 211891 · en_GB · 2017-12-14 · A001
Systemair UAB
Linų st. 101
LT–20174 Ukmergė, LITHUANIA
Phone [phone]
Fax [phone]
www.systemair.com