Middle Atlantic Products MMB Series User manual

MMB Series Monitor Mount
MMB-1X1-12BLK
Instruction Sheet
I-00846 Rev -
THANK YOU
PRODUCT FEATURES
Thank you for purchasing the MMB-1X1-12BLK monitor mount. Please read these instructions
thoroughly before installing or assembling this product.
• 17.6 lbs weight capacity
• Supports up to 32” diagonal screens
• Mounting for L5 Lecterns and worksurface with grommet holes.

AVERTISSEMENT: Des blessures graves ou mortelles peuvent survenir si un enfant grimpe sur le meuble d'un équipement audio
ou vidéo. Une télécommande ou un jouet placé sur le meuble peut encourager un enfant à grimper dessus et conduire à la chute
du meuble sur ce dernier.
AVERTISSEMENT: Le transfert d'un équipement audio ou vidéo sur un meuble qui n'a pas été spécialement conçu pour soutenir
un équipement audio ou vidéo peut entraîner l'effondrement ou le basculement du meuble sur un enfant et provoquer des
blessures graves ou mortelles.
Page 2
WARNING: Death or serious injury may occur when children climb on audio and/or video equipment furniture. A remote control or
toys placed on the furnishing may encourage a child to climb on the furnishing and as a result the furnishing may tip over on the
child.
WARNING: Relocating audio and/or video equipment to furniture not specifically designed to support audio and/or video equipment
may result in death or serious injury due to the furnishing collapsing or over turning onto a child.
WARNING: Failure to read, understand and follow the following information can result in serious personal injury, damage to the
equipment or voiding of the warranty. It is the responsibility of the Installer/User to ensure that this product is loaded according to
specifications.
WARNING: Exceeding the weight capacity may result in personal injury or equipment damage. The combined weight of all compo-
nents attached to the mount must not exceed weights listed on page 3.
WARNING: Be aware of pinch points and do not place
fingers in between moving parts.
IMPORTANT SAFETY INSTRUCTIONS
• Read these instructions.
• Keep these instructions.
• Heed all warnings.
• Follow all instructions.
• Clean only with dry cloth.
• Only use attachments/accessories specified by the manufacturer.
DANGER HAZARDOUS VOLTAGE: The lightning flash with the
arrowhead symbol, within an equilateral triangle is intended to alert the
user to the presence of uninsulated dangerous voltage within the
product’s enclosure that may be of sufficient magnitude to constitute a
risk of electric shock to persons.
WARNING: A warning alerts you to a situation that could result
in serious personal injury or death.
CAUTION: A caution alerts you to a situation that may result in
minor personal injury or damage to the product and/or property.
NOTE: A note is used to highlight procedures pertaining to the installation, operation, or maintenance of the product.
WARNING: Use this product for its intended use and only use
attachments recommended by the manufacturer.
WARNING: Do not use a damaged product. Return
damaged products to a qualified service center for repair.
WARNING: Not intended for outdoor use.
AVERTISSEMENT:Utilisez ce produit pour son utilisation prévue et utiliser uniquement les accessoires recommandés par le
fabricant.
AVERTISSEMENT:Ne pas utiliser un produit endommagé. Retour produits endommagés à un centre de service qualifié pour la
réparation.
AVERTISSEMENT:Non destiné à une utilisation en extérieur.
AVERTISSEMENT:Soyez conscient des points de pincement et de ne pas placer les doigts entre les pièces mobiles.
• Lire ces instructions.
• Conservez ces instructions.
• Respectez tous les avertissements.
• Suivez toutes les instructions.
• Nettoyer uniquement avec un chiffon sec.
• N'utilisez que des accessoires spécifiés par le fabricant.
AVERTISSEMENT:Refus de lire, comprendre et suivre la renseignements suivants peut traduire par de graves blessures, des
dommages à l'équipement ou invalider la garantie. Il est la responsabilité de l'installateur / utilisateur de s'assurer que ce produit
est chargé conformément aux spécifications.
AVERTISSEMENT:Dépasser la capacité de poids peut entraîner des blessures ou des dommages matériels. Le poids combiné de
tous les composants reliés au support de montage ne doit pas dépasser les grammages indiqués à la page 3.
INSTRUCTIONS IMPORTANTES SUR LA SÉCURITÉ
DANGER TENSION DANGEREUSE: Le symbole de la
pointe de flèche, dans un triangle équilatéral, est destiné à
alerter l'utilisateur sur la présence de tension dangereuse
non isolée dans l'enceinte du produit qui peut être d'une
ampleur suffisante pour constituer un risque d'électrocution.
AVERTISSEMENT: Un avertissement vous avertit d'une situation pouvant
entraîner des blessures graves ou la mort.
ATTENTION: Une attention vous avertit d'une situation pouvant entraîner
des blessures mineures ou des dommages au produit et/ou à la propriété.
REMARQUE: Une remarque est utilisée pour mettre en évidence les procédures relatives à l'installation, au fonctionnement ou à l'entretien du produit.

Page 3
WEIGHT RATINGS
Model Weight Rating
MMB-1X1X12BLK 17.6 lbs. Maximum Total Rated Load
32” MAX.
SUPPLIED COMPONENTS AND HARDWARE
Pole Base
E
Pole
B
Display Mount
Bracket
C
Adapter Plate
D
Cable Management
Clip
F
Grommet
Plate
G
(4x)
Flat Head
Screw
J
Carriage
Bolt
K
Monitor Mount
Knuckle
A
(5x)
Adhesive Pad
L
Thumb Screw
H
(4x)
Spacer
M-F
(4x)
M4x12 Pan
Head Screw
M-A
(4x)
M4x16 Pan
Head Screw
M-B
(4x)
M5x12 Pan
Head Screw
M-C
(4x)
M5x16 Pan
Head Screw
M-D
(4x)
Washer
M-E
Knob
M
5mm Hex Key
P
6mm Hex Key
N
4mm Hex Key
R
3mm Hex Key
S
NOTE: Additional hardware is included that may not be required for your installation.
MONITOR HARDWARE

Page 4
1. Insert carriage bolt (K) through adapter plate (D) as shown. (FIGURE A)
2. Attach adapter plate (D) to pole base (E) using (4x) flat head screws (J) and tighten using 4mm
hex key (R) as shown.
3. Apply (4x) adhesive pads (L) around the bottom of adapter plate (D) evenly spaced.
4. Insert pole base assembly into grommet hole in work surface. Using grommet plate (G) and knob
(M), tighten base securely to work surface.
MOUNTING THE BASE
• #2 Phillips Head Screwdriver • 5/16” Socket
• Standard Socket Set • 1/2” Drill Bit
• 5/16” Socket
REQUIRED TOOLS
WARNING: Use tools with caution and follow all necessary safety protocols.
AVERTISSEMENT: Utiliser des outils avec prudence et suivre tous les protocoles de sécurité
nécessaires.
K
E
J
R
D
L
G
M
FIGURE A
NOTE: If using grommet hole for wire management, position assembly with
cutout in line with wires before tightening assembly in place.
GROMMET MOUNTING

Page 5
1. Insert carriage bolt (K) through adapter plate (D) as shown. (FIGURE B)
2. Attach adapter plate (D) to pole base (E) using (4x) flat head hex screws (J) and tighten using
4mm hex key (R) as shown.
3. Apply (4x) adhesive pads (L) around the bottom of adapter plate (D) evenly spaced.
4. Using a drill from bottom of worksurface, drill a 1/2” diameter hole using one of the factory drilled 1/2”
pilot hole locations.
5. Insert pole base assembly into drilled hole in work surface. Using grommet plate (G) and knob
(M), tighten base securely to work surface.
MOUNTING THE BASE (CONTINUED)
L
K
E
J
R
G
M
D
FIGURE B
L5 LECTERN MOUNTING

Page 6
1. Slide cable management clip (F) onto pole (B) as shown. (FIGURE C)
2. Loosen set screws in pole base (E) and push onto pole (B) until it bottoms out.
3. Using 3mm hex key (S), tighten set screws to lock pole onto base.
ASSEMBLING POLE TO BASE
B
E
F
S
FIGURE C

Page 7
1. Slide monitor mount knuckle (A) onto pole (B) as shown. (FIGURE D)
2. Position monitor mount knuckle (A) at desired height.
3. Tighten set srew to lock monitor mount knuckle onto pole (B) using 5mm hex key (P).
ASSEMBLING POLE TO BASE
A
B
P
FIGURE D

Page 8
FLUSH DISPLAY MOUNT BRACKET INSTALLATION
1. Using supplied display mount screws, select the appropriate screw size and length ensuring screw
does not bottom out in mounting hole, or damage to display may occur.
NOTE: If you feel resistance, stop immediately and try a shorter screw. If supplied screws are still too
long, use supplied spacers to take up slack.
2. Align display mount bracket (C) with mounting holes on the back of display. Use (4x) display mount
screws (M-A - M-D) and (4x) washers (M-E) to secure the display mount brackets to your display.
(FIGURE E)
C
M-A - M-D
M-E
Tab must face up.
FIGURE E

Page 9
RECESSED OR RAISED BACK DISPLAY MOUNT BRACKET INSTALLATION
1. Using supplied display mount screws, select the appropriate screw size and length ensuring screw
does not bottom out in mounting hole, or damage to display may occur.
NOTE: If you feel resistance, stop immediately and try a shorter screw. If supplied screws are still too
long, use supplied spacers to take up slack.
2. Align display mount bracket (C) with mounting holes on the back of display. Use (4x) display mount
screws (M-A - M-D), (4x) washers (M-E), and (4x) spacers (M-F) to secure the display mount brackets
to your display.
(FIGURE F)
Tab must face up.
C
M-A - M-D
M-E
M-F
FIGURE F

Page 10
1. With monitor attached, slide display mount hooks onto knuckle plate as shown.
(FIGURE G)
2. Using thumb screw (H), secure display mount to monitor mount knuckle (A). (FIGURE G)
MONITOR INSTALLATION
Display Mount Hooks
H
FIGURE G
Knuckle Plate

Page 11
ADJUSTMENT AND CABLE MANAGEMENT
1. To adjust display angle, loosen socket cap screws on the side of the monitor mount knuckle (A)
using 6mm hex key (N) and retighten when desired angle is set. (FIGURE H)
2. Route cables through cable management clip (F).
(FIGURE J)
3. When installed in a grommet hole, slot in adapter
plate can be used to feed cables through grommet
hole.
NOTE: Cable management clip provides storage
for supplied hex keys for future adjustment.
FIGURE H
FIGURE J
N

For warranty information, refer to http://www.middleatlantic.com/company/about-us.aspx#warranty
Corporate Headquarters
Corporate Voice: 973-839-1011 - Fax: [phone] / International Voice: [phone] -
Fax: [phone]
www.middleatlantic.com - [email protected]
Middle Atlantic Canada
Voice: 613-836-2501 - Fax: [phone] / ca.middleatlantic.com -
[email protected]
Factory Distribution
USA: NJ - CA - IL Canada: ON - BC
At Middle Atlantic Products we are always listening. Your comments are welcome.
Middle Atlantic Products is an ISO 9001 and ISO 14001 Registered Company.
WARRANTY
Page 12