Vicon VM614RK-2 User manual

Vicon part number 8009-8068-10-00 Rev 1100 Section 13
XX068-10-00
VM614RK-2 RACK-MOUNTING KIT FOR THE
VM614-2 VIDEO MONITOR
Copyright © 2000 Vicon Industries Inc. All rights reserved.
Product specifications subject to change without notice.
Vicon and its logo are registered trademarks of Vicon Industries Inc.
VICON INDUSTRIES INC., 89 ARKAY DRIVE, HAUPPAUGE, NEW YORK 11788
TEL: 631-952-CCTV (2288) FAX: 631-951-CCTV (2288) TOLL FREE: 800-645-9116
24-Hour Technical Support: 800-34-VICON (800-348-4266
UK: 44/(0) 1489-566300 INFOFAX: 800-287-1207 WEB: www.vicon-cctv.com

XX068-10-00 Rev 1100 VM614RK-2Contents •• i
Contents
Introduction.......................................................................................................................................1
Installation..........................................................................................................................................3
Unpacking and Inspection ...................................................................................................................3
Inspection For Visible Damage.............................................................................................................3
Inspection For Concealed Damage.......................................................................................................3
Kit Contents.........................................................................................................................................3
Assembling the Baseplate to the Monitor ............................................................................................4
Assembling the Side Supports to the EIA Rack....................................................................................4
Assembling the Monitor/Baseplate to the Side Supports.....................................................................4
Assembling the Monitor Bezel to the Rack Mount................................................................................6
Maintenance......................................................................................................................................6
Shipping Instructions......................................................................................................................7
Technical Information.....................................................................................................................9

XX068-10-00 Rev 1100 VM614RK-2Introduction •• 1
Introduction
The information in this manual covers the installation of the VM614RK-2 Rack-Mounting Kit for the VM614-2
Monitor. This unit should be installed by a qualified technician using approved materials. Read these instructions
through completely before attempting installation.
The VM614RK-2 Rack-Mounting Kit is designed to permit mounting the Vicon VM614-2 video monitor in an EIA
standard 19-inch equipment rack. The mounting kit consists of two triangular side supports (gussets), one
baseplate, one extension plate, two brackets, one front panel (bezel) and hardware. Refer to Figure 1.
Figure 1
Exploded View of Monitor Rack

2•• Introduction XX068-10-00 Rev 1100 VM614RK-2
Notes

XX068-10-00 Rev 1100 VM614RK-2Installation •• 3
Installation
Unpacking and Inspection
All Vicon equipment is tested and inspected before leaving the factory. It is the carrier’s responsibility to deliver
the equipment in the same condition as it left the factory.
Inspection For Visible Damage
Immediately inspect the cartons upon delivery. Make a note of any visible damage on all copies of the carrier’s
freight bill.
Make sure the carrier’s agent (the person making the delivery) signs the note on all copies of the bill. If the agent
does not have claim forms, contact the carrier’s office.
Inspection For Concealed Damage
As soon as possible after delivery, unpack the unit and inspect it for concealed damage. Do not discard the
carton or packing materials. If the unit is damaged, contact the carrier immediately and request forms for filing a
damage claim. Make arrangements for a representative of the carrier to inspect the damaged equipment.
If the equipment must be returned for repair, follow the Shipping Instructions at the end of this manual.
Kit Contents
Prior to starting assembly, become familiar with the components in the mounting kit. Refer to Figure 1. The
rack-mounting kit includes the following parts:
Baseplate
Extension plate
Brackets
Left side support bracket (gusset)
Right side support bracket (gusset)
Front panel (bezel)
Additionally, the accessory kit supplied contains a variety of screws and hardware required for assembling the
rack mount. Refer to Table 1. In addition to these screws, six screws of a type suitable to attach the monitor
mount to the EIA rack are required. These are commonly No. 10-32 screws, but individual rack manufacturers
may use other types.

4•• Installation XX068-10-00 Rev 1100 VM614RK-2
Table 1
Accessory Kit
Component Quantity Function
7 x 3/4 type AB screw 4Fastens baseplate to monitor
6-32 x 1/4-in. pan head screw
(black) 4Fastens front bezel to rack mount
6 x 1/2-in. self-tapping pan
head screw 10 Locks baseplate to side supports, attaches extension plate to baseplate and bracket to
extension plate
Bracket 2Fastens monitor to extension plate
Assembling the Baseplate to the Monitor
To assemble the baseplate to the monitor, use the following procedure. Refer to Figure 1 and 2 as needed.
1. Attach the extension plate to the baseplate with four (4) 6x1/2 self-tapping screws. Secure the brackets to
the extension plate with the 6x1/2 self-tapping screws. Refer to Figure 2.
2. Turn the monitor upside down on a clean, flat workspace.
3. Attach the baseplate/extension plate to the monitor base, using the 7 x 3/4 screws at the two sets of holes
toward the front and rear of the monitor base. Refer to Figure 2.
Assembling the Side Supports to the EIA Rack
The right and left side support brackets (gussets) mount directly to the EIA rack. Refer to Figure 1.
1. Position the side supports so that there is enough clearance to attach the front panel (bezel).
2. Attach each side support to the rack using three screws compatible with the rack’s screw holes. These
screws are not included in the accessory kit.
Assembling the Monitor/Baseplate to the Side Supports
The baseplate/extension plate has two tabs bent down on each end. Note that each side support has two
corresponding slots. Refer to Figure 1.
1. Carefully lift the monitor/baseplate assembly into position between the side brackets, with the front of the
monitor facing the front of the rack. Position the monitor/baseplate assembly so that the tabs on the
baseplate go into the slots in the side supports. Take care that all four tabs are properly seated.

XX068-10-00 Rev 1100 VM614RK-2Installation •• 5
2. Lock the baseplate into position using the 6 x 1/2 inch self-tapping screws from the accessory kit. Refer to
Figure 2. Find the upward-bent tab on the rearmost point of each side support. Thread one screw into each
tab from rear to front. Some force may be required, since the screws are cutting threads in the metal of the
side support.
3. The remaining two self-tapping screws are inserted through the front flange of the baseplate. The front flange
of the baseplate has the word FRONT stamped into it.
Figure 2
Baseplate Assembly

6•• XX068-10-00 Rev 1100 VM614RK-2
Assembling the Monitor Bezel to the Rack Mount
1. Locate the four threaded spacers on the front edges of the rack mount kit. Hold the front bezel so that the
holes in the bezel match the threaded spacers. If the spacers and the holes in the bezel do not match
exactly, it may be necessary to loosen the six screws attaching the side supports to the rack and
reposition the side supports slightly until the spacers and holes match. Retighten the six side support
screws.
2. Attach the bezel with the four black 6-32 x 1/4 inch screws. Do not fully tighten the four screws.
3. Check the bezel alignment and then tighten the bezel screws. Do not overtighten.
4. Complete all cable and power cord connections to the monitor. This completes installation.
Maintenance
The Vicon monitor rack mount kits require no scheduled maintenance. The front bezel may be dusted with a soft
cloth as needed.

XX068-10-00 Rev 1100 VM614RK-2Shipping Instructions •• 7
Shipping Instructions
Use the following procedure when returning a unit to the factory:
1. Call or write Vicon for a Return Authorization (R.A.) at one of the locations listed below. Record the name of
the Vicon employee who issued the R.A.
Vicon Industries Inc.
89 Arkay Drive
Hauppauge, NY 11788
Phone: 631-952-CCTV (2288); Toll-Free: 1-800-645-9116; Fax: 631-951-CCTV (2288)
For service or returns from countries in Europe, contact:
Vicon Industries Ltd
Brunel Way
Fareham, PO15 5TX
United Kingdom
Phone: [phone]; Fax: [phone]
2. Attach a sheet of paper to the unit with the following information:
a. Name and address of the company returning the unit
b. Name of the Vicon employee who issued the R.A.
c. R. A. number
d. Brief description of the installation
e. Complete description of the problem and circumstances under which it occurs
f. Unit’s original date of purchase, if still under warranty
3. Pack the unit carefully. Use the original shipping carton or its equivalent for maximum protection.
4. Mark the R.A. number on the outside of the carton on the shipping label.

XX068-10-00 Rev 1100 VM614RK-2Technical Information •• 9
Technical Information
MECHANICAL
Mounting Size: 14 in. (356 mm) diagonal monitor screen.
Size: Single monitor.
Construction: Bezel: aluminum, black semi-gloss enamel.
Baseplate: zinc-plated steel
Side brackets: zinc-plated steel.
Dimensions: Height: 14.0 in. (356 mm).
Width: 19.0 in. (483 mm).
Depth: 14.0 in. (356 mm), excluding monitor.
Weight: 9.4 lb (4.3 kg).