Tactic FPV-C2 User manual

FPV-C2
TM
VIDEO CAMERA 600TVL
Tactic’s FPV-C2 rst person video camera is great for capturing video images
while mounted in an R/C model. Its small size and weight is perfect for mounting
in tight places. A video transmitter is required to transmit the images to a video
receiver, monitor, or goggles (all available separately). See Tactic’s line of video
transmitters and other equipment at http://www.tacticrc.com/fpv.
INSTALLATION
Various methods can be used to mount this camera, including double-sided tape,
hook-and-loop material, etc. (all available separately). Mount the camera to provide
optimum view, yet with adequate physical protection from impacts. For proper
video alignment, mount the camera so the connector and wires are oriented up
or down.
IMPORTANT! Keep all components clear of moving parts in/on the
model! Never allow water/liquids to make contact with the camera to
avoid permanent damage to the electronics and/or imaging components.
CONNECT TO VTX & INPUT POWER
Connect the camera to the Tactic
transmitter using the included
harness. To power the transmitter,
connect to the model’s LiPo batteries
balance connector (2~4S). Use one
of the included adaptors if using a
2S or 3S pack. NOTE: If your model
uses a 6S battery, you will need to
create a custom adaptor. See your
Transmitter’s instructions for more
information. To power the camera, plug the connector into the receiver or another
4.8~5V source. Do not exceed 5V or you risk damage to the camera. Check the
specs of your ESC to conrm the voltage.
DIP SWITCH SETTINGS
Switch 1: Flips the video vertically
Switch 2: PAL / NTSC formats
Switch 3: Flips the video horizontally

The camera lens can be adjusted for optimum image focus. With the camera
turned on and while viewing an image on a separate video monitor, loosen the
locking ring on the lens housing. Carefully turn the end of the lens clockwise or
counter-clockwise until the optimum focus is viewed on the monitor. Then gently
tighten the locking ring on the lens housing, being careful NOT TO OVER-TIGHTEN.
Input power: 5V DC, ~180mA Mode: video only
Video resolution: 600TVL Sensor: 1/4 inch CMOS
Field of view: 2.3mm 100° Weight: 10.3g (0.36 oz.)
Color encoding: NTSC (720H x 480V) / PAL (720 x 576)
Video out: 1.0Vp-p, PAL (75 ohms) / NTSC (30 ohms)
Dimensions: 30 x 30 x 26mm (1.18 x 1.18 x 1.02”)
Tactic warrants this product to be free from defects in materials and workmanship
for a period of one (1) year from the date of purchase. For service on your Tactic
product if purchased in the U.S.A. or Canada, send it postpaid and insured to:
HOBBY SERVICES Tel: [phone]
3002 N. Apollo Dr., Suite 1 (9:00am - 5:00pm CST, M-F)
Champaign, IL 61822 E-mail: [e-mail]
If purchased in the European Union, send it postpaid and insured to:
Service Abteilung Revell GmbH Tel: [phone] (nur für Deutschland)
Henschelstrasse 20-30 Email: [e-mail]
32257 Bünde Germany
•This product is suitable only for people of 14 years and older. This is not a toy!
•
No part of this manual may be reproduced in any form without prior permission.
•The contents of this manual are subject to change without prior notice.
•Tactic is not responsible for the use of this product.
WARNING: CHOKING HAZARD - May contain small parts. Keep away from
children under 3 years. Please retain packaging for future reference.
WARNING: This product contains a chemical known to the state of California to
cause cancer and birth defects or other reproductive harm.
Distributed in the EU by Revell GmbH, Bunde Germany
© 2016 Tactic, a Hobbico company.
Made in Dongguan City, China TACZ5035
IMAGE FOCUS ADJUSTMENT
SPECIFICATIONS
1-YEAR WARRANTY