TAG HARDWARE SYMPHONY User manual

INSTALLATION GUIDE
SYMPHONY Desk Mount
components
Horizontal Bars
STEP 1 : Space horizontal bars (H) with channel facing up
STEP 1 : Space horizontal bars (H) with channel facing up
Vertical Bars End Caps Base Mounts 5/16-24 x 2” BoltM5 Set Screw
tools
5/16” Washer
3/8” Drill Bit 3/8” Drill Bit Jig K Jig O (Shop Supplied)
install prep
STEP 1 : Space horizontal bars (H) with channel facing up
(included)
(included)
STEP 1 : Space horizontal bars (H) with channel facing up
6”
(included)
Recommended
but not required
Refer to PART F
for placement
Drill Wrench Tape Measure
Allen Key 2.5 mm
(included)
H
INSTALL PREPARATION
PART A:
Page 1
WARNING:
This product can
expose you to
chemicals including
chromium (hexavalent
compounds), which
are known to the
State of California to
cause cancer and
birth defects or other
reproductive harm.
For more information,
visit
www.p65warnings.
ca.gov
ABC D EFG
IJKL
A
AA
MNO

STEP 3 : Insert End caps (E) into channel on horizontal bars (H). Tighten set screws while pushing End cap.
Insert vertical
bars and end
caps
1
Insert
Jig K & O
2
Secure
corners of
Vertical Bars
3o
O
II
O
O
B
B
ASSEMBLY
PART B:
Page 2
BCH
C
O
O
K
C
C
B
K

Secure
corners of
Vertical Bars
4
Tighten
Horizontal
Bars
5
Attach
Base
Mounts
6
B
I
A
O
O
II
BB
L
O
B
DE
E
ASSEMBLY & WALL INSTALLATION
PART C:
Page 3
OO
O

Measure
distance
(“z”) for hole
placement
7
Drill 3/8”
holes into
table surface
8
Fix
Symphony
to table
surface
9
J
('X') ('Y') ('X')
Custom overhangh / Assembly without Jigs
- Recommended Max. 'X': 12 inches
- Recommended Max. 'Y': 40 inches
D D
Table
Table
Table
Table
Table
Table
D
G
F
G
F
Up to 1 3/4” table
top thickness
D
WALL INSTALLATION
PART D:
Page 4

Jig O
(Shop
Supplied)
.75”
9” 17.5”
Recommended but not
required
O
('X')
('Y')
('X')
Custom overhangh / Assembly without Jigs
- Recommended Max. 'X': 12 inches
- Recommended Max. 'Y': 40 inches
Assembly Without A Jig
Recommended maximum ‘X’: 12”
Recommended maximum ‘Y’: 40”
X” Y” X”
1. Standard cleaning: wipe clean with
a slightly damp cloth. Do not use highly
acidic or alkaline cleaners, other non-
recommended commercial cleaners or
polishes, or treated cloths that have been
used to clean other furniture. Do not steam
or use heat.
2. Stain removal: Mix denatured alcohol
(methylated spirits) and warm water in
equal proportions, dampen a clean cloth
with the mixture, and wipe stain until it’s
removed. Denatured alcohol is poisonous
and highly ammable, but evaporates
quickly and cleanly and will remove stains
from imitation leather surfaces. Do not
steam or use heat.
Leave Behind Imitation
Leather Care Instructions
Jig1 Standard use scheme
13 1/2 inch
versions
23 inch
versions
35 inch
versions
47 inch
versions
11/16'' 5 11/64
13.5” 23”
35” 47”
O
””
9”
Jig1 Standard use scheme
13 1/2 inch
versions
23 inch
versions
35 inch
versions
47 inch
versions
11/16'' 5 11/64
O
””
9”
Jig1 Standard use scheme
13 1/2 inch
versions
23 inch
versions
35 inch
versions
47 inch
versions
11/16'' 5 11/64
O
9”
Jig1 Standard use scheme
13 1/2 inch
versions
23 inch
versions
35 inch
versions
47 inch
versions
11/16'' 5 11/64
O
9”
Jig O Positioning
PART F:
Page 5