Talent BL63 User manual

User Manual
www.talentaudio.comwww.talentaudio.com
Model: BL63
7. Troubleshooting
Following are a few common problems that may occur during operation. Here
are some suggestions for easy troubleshooting:
A. The xture does not work, no light
1. Check the connection of power and mains fuse.
2. Measure the mains voltage on the main connector.
B. Not responding to DMX controller
1. DMX LED should be on. If not, check DMX connectors and cables to verify they are
linked properly.
2. IftheDMXLEDisonandthechanneldoesnotrespond,checktheaddresssettings
and DMX polarity.
3. IfyouhaveintermittentDMXsignalproblems,checkthecableandxture
connectors for proper function.
4. Try to use another DMX controller for comparison.
5. Check if the DMX cables are run near or alongside high voltage cables that
may cause interference to the DMX interface circuit.
C. Some xtures don’t respond to the controller
1. You may have a break in the DMX cabling. Check the LED for the response
of the master/ slave mode signal.
2. WrongDMXaddressinthexture.Settheproperaddress.
D. No response to sound
1. MakesurethexturedoesnotreceiveDMXsignal.
2. Check microphone to see if it is good by tapping the microphone.
8. Fixture Cleaning
Clean with soft cloth using a very mild household detergent. Always dry the
parts carefully.
WARRANTY
Talent is dedicated to providing their customers with quality product. As such, all Talent products are
warranted free from defects in material and workmanship for a period of One Year from the date of purchase.
Warranty registration is not required, but purchasers are asked to retain their receipt as proof of purchase.
Warranty does not apply to misuse, abuse, neglect, accident, improper use, etc. For complete customer
satisfaction, Talent resellers are asked to act as agents for the purpose of handling warranty claims.
Please return your Talent product to your place of purchase prepaid. Many Talent resellers require a return
authorization (also known as an RA or RMA). Please contact your Talent reseller for more details.

2 3
WARNING
•PleasekeepthisUserManualforfutureconsultation.Ifyousellthexturetoanother
user, be sure that they also receive this instruction booklet.
•Whenunpackingforrstuse,checkcarefullythereisnotransportationdamage.
• Before operating, ensure that the voltage and frequency of power supply match the
 powerrequirementsofthexture.
• Disconnect main power before servicing and maintenance.
•Useasafetycablewhenmountingthisxture.
•Maximumambienttemperatureis40° C.
•Intheeventofaseriousoperatingproblem,stopusingthextureimmediately.Never
 trytorepairthextureyourself.Repairscarriedoutbyunskilledpersonscanleadto
damage or malfunction. Please contact the nearest authorized technical assistance
center. Always use the same type spare parts.
• Do not connect the device to any dimmer pack.
• Do not touch any wire during operation, as there might be a hazard of electric shock.
•Topreventorreducetheriskofelectricalshockorre,donotexposethextureto
rain or moisture.
• The housing must be replaced if it is visibly damaged.
•DonotlookdirectlyattheLEDlightbeamwhilethextureison.
• Donotconnectinseriesmorethan30units.Useanothercircuittosupplyadditionalxtures.
CAUTION
Therearenouserserviceablepartsinsidethexture.Donotopenthehousingorattempt
any repairs yourself. In the unlikely situation your unit may require service, please contact
your nearest dealer.
Please read the instructions carefully, which include important
information about installation, operation, and maintenance.
1. Safety Instructions
2. Technical Specications
3. Installation
4. How to Set the Unit
5. How to Control the Fixture
6. DMX512 Conguration
7. DMX512 Connections
8. Troubleshooting
9. Fixture Cleaning
TABLE OF CONTENTS
2. Technical Specications
3, 5, 7 channel with optional RGB mixed wall lamp
4 push buttons with 4-digit LED display
Four modes: Automatic,SoundActivated,DMX512,Master/Slave
Light source: 63x10mmUltraBrightLEDs(21red,21green,21blue)
Bulb angle: 20°-40°
Power consumption: 12 watts
Power input: 100-240VAC50-60Hz
Dimensions: 328.6mmLx120mmHx150mmD
Weight: 2.25 kg
1. Safety Instructions

4 5
4.2 Main Function Chart
4. How To Set The Unit
4.1 Control Panel
5. How to control the xture
Therearetwowaystocontrolthextureremotely:
A. Universal DMX controller
B.Master/Slaveoperation
A. Universal DMX controller
ThexturecanbeoperatedremotelybyauniversalDMXcontroller.Programtwoor
morescenesintoachase,andthenlinkthexturestotheuniversalDMXcontroller.
B. Master/Slave operation
Thexturewillallowyoutolink16xturestogetherandoperatewithoutacontroller.
InMaster/Slavemode,therstxturewillcontroltheotherstogiveanautomatic,
soundactivated,synchronizedlightshow.Therstxture’sDMXinputcablewill
have nothing connected to it, and the other xtures will be set in slave mode
automatically.TheirDMXinputcablesconnecttothepreviousxture’sDMXoutput
cable(daisychain).AnyxturecanactasaMasterorasaSlave.
3. Installation
Theunitshouldbemountedvia theholesonitsbracket, andmustbexed
rmlytoavoidvibrationandslippageduringoperation.Alwaysensurethatthe
structuretowhichyouareattachingthelightingxtureissecureandableto
support10timestheunit’sweight.Wheninstallingthexture,useasafetycable
that can hold 12 times the weight of the unit.
6. DMX512 Conguration
3 channels Mode:

6 7
1. Ifyourcontrollerhasa5-pinDMXoutput,youneedtousea5-pinto3-pin
adapter cable.
2. Linkthexturestogetherina“daisychain”byconnectingXLRcablesfrom
 theoutputofthexturetotheinputofthenextxture.Thecablecannotbe
 branchedorsplittoa“Y”cable.Inadequateordamagedcables,soldered
joints, or corroded connectors can easily distort the signal and shut down
the system
3. TheDMXoutputandinputconnectorsarepass-throughtomaintaintheDMXcircuit
 whenoneoftheunits’powerisdisconnected.
4. Atthelastxture,theDMXcableshouldbeterminatedtoreducesignal 
 errors.Soldera120ohm1/4WresistorbetweenPin2(DMX-)andPin3
 (DMX+)intoa3-pinXLRplugandconnectittothelastxture’sDMXoutput.
5. Eachlightingxturemusthaveitsaddresssettoreceivedatasentbythecontroller.
 Theaddressnumberisbetween0-511(usually0&1areequalto1).
6. 3-pinXLRconnectorsaremorecommonthan5-pinXLR.
 3-pinXLR:Pin1: GND,Pin2:Negativesignal(-),Pin3:Positivesignal(+)
 5-pinXLR:Pin1: GND,Pin2:Negativesignal(-),Pin3:Positivesignal (+)
  Pin4/5:Notused.
7 channels Mode:
5 channels Mode: 7. DMX512 Connections
TheDMX512isusedwidelyinintelligentlightingcontrol,withamaximumof512channels.