TalentPros TPS-1530 User manual

TalentPros
TPS-1530
User Guide

TPS-1530 Power Supply
The TPS-1530 requires an external ATX power supply. Just
choose the ATX power supply commonly used in PCs. Insert the
two PCIe 8-pin connectors into the power holes on the left and
right of the back of the TPS-1530.

TPS-1530 Boot Up
Please confirm:
1. Power is properly connected
2. SD card is inserted
Then you can turn on the TPS-1530.

TPS-1530 Connection Method
TPS-1530 provides two ways to connect with the computer:
1. Through ETH (first port)
2. Via USB (third port)
1
2

m-View Management System
Main Page
Open the m-View and you will first enter the main page, all
TPS-1530 Devices connected to the same IP domain will be
displayed here.

Function Menu
Right-click on TPS-1530 Device icon and select “Function
Menu”:

Select “Device Status” to view TPS1530 real-time status.

Select “VRM Setting” to modify the VRM voltage.

Network Setting
Right-click the device icon on the main page and select
"Network Setting". Here you can set DHCP or Fixed IP and
manually assign address:

Save Bitstream to micro-SD Card
On the main page, switch the bookmark from “Overview” to
“Others” and click “Upload to SD Card”.
Select the SD card folder where you want to save the bitstream,
select the bitstream you want to download, select the control
device, and press "Yes":

Automatically download bitstream when booting
If you have saved bitstream into the micro-SD Card, you can set
TPS-1530 to automatically download bitstream when booting.
Go to “Function Menu” and choose “DL Bitstream”:
Select the bitstream with the SD card folder ID, and then check
"Automatic download bitstream". Each time TPS-1530 is
restarted, the bitstream is automatically loaded from this folder
locations:

Automatically set VRM when booting
VRM voltage can be set through m-view or through
VU9P_Config.txt which is saved in SD card.
If you want to automatically load the corresponding VRM value
at the same time when the bitstream is automatically download,
you need to modify the VU9P_Config.txt as shown below:

Vivado Hardware Manager
1. Open Vivado Hardware Manager
2. Click “Open Target” → “Auto Connect”

3. Enter the device IP
If you connect TPS-1530 via USB-JTAG, skip to step 4.
Enter the following commands in the TCL Console window:
open_hw_target -xvc_url <your_TPS_1530_ip>:2542

4. Device connected successfully
If the FPGA name is displayed, as shown below, it means that
the connection is successful:
If the TPS-1530 connected by Ethernet:
If the TPS-1530 connected by USB-JTAG:

5. Download Bitstream
Right-click on FPGA Name, select "Program Device".
Select the .bit file and press "Program".

6. FPGA programmed successfully
If the Status of the FPGA becomes "Programmed", means the
programming is successful.

TPS-1530 Pinout Table
Clock Source:
Function Description
Net Name
VU9P
Number
VCCO
Bank
SYS GC(0): 300MHz
SYSCLK0_300M-
AY38
42
SYSCLK0_300M+
AY37
42
SYS GC(1): 300MHz
SYSCLK1_300M-
AW19
64
SYSCLK1_300M+
AW20
64
SYS GC(2): 300MHz
SYSCLK2_300M-
E32
47
SYSCLK2_300M+
F32
47
SYS GC(3): 300MHz
SYSCLK3_300M-
H16
70
SYSCLK3_300M+
J16
70
SYS GC(4): 156.25MHz
SYSCLK4_15625M-
AV19
70
SYSCLK4_15625M+
AU19
70
GTY230 REFCLK0: 156.25MHz
MGT230_REFCLK1-
T10
Q230
MGT230_REFCLK1+
T11
Q230
GTY231 REFCLK0: 156.25MHz
MGT231_REFCLK1-
M10
Q231
MGT231_REFCLK1+
M11
Q231
GTY230 REFCLK1: 156.25MHz
MGT230_REFCLK1-
P10
Q230
MGT230_REFCLK1+
P11
Q230
GTY231 REFCLK1: 156.25MHz
MGT231_REFCLK1-
K10
Q231
MGT231_REFCLK1+
K11
Q231
PCIe Gen1X1 CLK
MGT226_REFCLKP
AM11
Q226
MGT226_REFCLKN
AM10
Q226

Others:
Function Description
Net Name
VU9P
Number
VCCO
Bank
QSFP0 control I/O
VU_QSFP0_MODSKLL_LS
BE16
64
VU_QSFP0_RESETL_LS
BE17
64
VU_QSFP0_MODPRSL_LS
BE20
64
VU_QSFP0_INTL_LS
BE21
64
VU_QSFP0_LPMODE_LS
BD18
64
QSFP1 control I/O
VU_QSFP1_MODSKLL_LS
AY20
64
VU_QSFP1_RESETL_LS
BC18
64
VU_QSFP1_MODPRSL_LS
BC19
64
VU_QSFP1_INTL_LS
AV21
64
VU_QSFP1_LPMODE_LS
AV22
64
USB-UART interface*
FT2232H_VU_USB_UART_TX
BF18
64
FT2232H_VU_USB_UART_RX
BB20
64
PCIe Gen1X1 TX/RX
MGT227_TX0_P
AF7
Q227
MGT227_TX0_N
AF6
Q227
MGT227_RX0_P
AF2
Q227
MGT227_RX0_N
AF1
Q227
PCIe Gen1X1 PERST
VU_PCIE_PERST_LS
BD21
64
*The USB-UART interface is port 2 (third port), as shown on page 2.

QSFP: