Tandem Vertical Challenger User manual

How to Measure a
Vertical Jump
Tandem’s Vertical Challenger is the perfect tool to meas-
ure and improve vertical jump. It is adjustable from 4 to 12
feet to accommodate athletes of any size or skill level.
1. Using the height settings guide (guide can be found
on sticker on base of unit), set the device to the
proper range to obtain a standing reach measure-
ment. Height ranges are in two foot increments.
2. Have the athlete stand under the device and reach
as high as possible, keeping feet at on the ground.
Point the nger tips to move the highest vein
reached and record this value as standing reach.
3. Reset the veins and have the athlete jump from a
stationary position or take a few steps back and
jump as high as possible. Record the highest vein
reached as the jump reach. Be sure to reset the veins
after each jump.
4. Subtract the standing reach from the jump reach to
determine vertical jump score.
User tip: If the athlete’s standing or jump reach falls out-
side of the height setting range and no measurement can
be obtained, then the unit will need to be adjusted to the
next height setting range so a standing or jump reach can
be measured.
Other uses for the Vertical Challenger:
• Measure the vertical jump from a standing position
with no step approach.
• Use as a conditioning tool with repetitive speed jumps.
• Use to increase vertical jump with maximum station-
ary jumps.
• Use to measure an individual’s height.
Vertical
Challenger
Height Settings
*For height measurements of 4’-6’, 5’-7’, and 6’-8’, the mid-
dle pole must be in lowest setting. Lowest setting is ob-
tained when middle pole meets resistance of challenger
base and cannot be moved downward further.
4’-6’: middle pole at lowest setting, top pole at 4
5’-7’: middle pole at lowest setting, top pole at 5
6’-8’: middle pole at lowest setting, top pole at 6
7’-9’: middle pole at 7, top pole at 6
8’-10’: middle pole at 8, top pole at 6
9’-11’: middle pole at 9, top pole at 6
10’-12’: middle pole at X, top pole at X
During use, refer to height settings guide located on base
of unit.
SUPPORTS • EQUIPMENT • TRAINING
440 Baxter Avenue • Louisville, KY 40204
800.766.1098 • TandemSport.com

• Telescopes to accurately measure vertical
jump from 4 to 12 feet
• Heavy duty base with wheels and 10 kg
weight allows for portability and stability
• Movable veins are placed at 1” increments
to allow for accurate jump measurement
• Highest vein reached remains angled al-
lowing accurate jump reading to be ob-
tained
• Reset pole quickly returns veins into posi-
tion for next use
• Can measure the height of individual,
standing arm reach, standing vertical, or
vertical jump with approach
• Ships in two boxes totaling 50 lbs
Assembly Instructions:
Align Part 1 with Part 2 and secure with 2 bolts and
washers. Align Part 3 with the 4 bolt openings on Part
1 and Part 2 and secure with 4 bolts and washers. Re-
move 2 pre-positioned screws near the top of Part 3
and align Part 4 screw openings (on curved end of
piece) with the newly exposed screw openings on Part
3. Reposition the 2 screws in the openings and tighten.
Position Part 5 in the round opening on Part 2 and se-
cure with bolt and washer. Place 10 kg weight on se-
cured weight rod. Use Allen wrench to tighten all bolts
before use.
Parts List:
Part 1 - Wheel component base bar
Part 2 - Weight component base bar
Part 3 - Telescoping Pole
Part 4 - Curved pole with movable measurement veins
Part 5 - Weight rod
10 kg weight
7 bolts and washers
Allen Wrench
Reset Pole
SUPPORTS • EQUIPMENT • TRAINING
440 Baxter Avenue • Louisville, KY 40204
800.766.1098 • TandemSport.com
Getting Started