TARGET TECHNOLOGY PR-4000-ANZ User manual

PAGER RECEIVER
INSTRUCTION MANUAL
PR-4000-ANZ

2
HOW IT WORKS
The Pager Receiver connects to our Alert Sensors.
When the connected Sensors are interrupted or
activated, the Sensor sends a signal to the Pager
Receiver which plays a tone to alert you.
There is a range of up to 1.6 km from the Sensors to the
Alert Pager.
The Alert Pager will receive signals from all of our
Alert Sensors.
ABOUT.
P
I
R
S
e
n
s
o
r
S
o
l
a
r
B
e
a
m
S
e
n
s
o
r
s
P
r
o
b
e
S
e
n
s
o
r
s
Detects heat
motion in front of
the Sensor.
Detects motion
that passes
between Beam
Sensors.
Detects metallic
motion that
passes near
Sensor.
D
i
r
e
c
t
i
o
n
a
l
P
r
o
b
e
S
e
n
s
o
r
s
Detects direction
of metallic motion
that passes near
Sensor.

3
SET UP.
CHARGING YOUR PAGER
The charging port is located on the left side of the Pager.
This can be charged with any USB micro charger.
• The battery icon will blink while charging
• Charge time will typically be 6-8 hours.
• If the battery is dead for several months, all
programming may be lost.
POWERING YOUR PAGER
• Press and hold the POWER button for 2 seconds.
• To turn the POWER off, unlock the keypad then press
and hold the POWER button for 2 seconds.
LOCKING & UNLOCKING
If no buttons are pressed for 15 seconds, the keypad
will automatically lock.
• A key icon will appear at the top of the display when
the keypad is locked.
• To unlock the keys, press and release the UP and
DOWN buttons at the same time. The key icon will
disappear.
• To lock the keypad, press and release the UP and
DOWN buttons at the same time. The key icon will
appear.

4
SETTINGS
Volume
• Press and release the POWER button.
• With the keypad unlocked, press and release the
MODE button.
• The speaker icon will ash in the display.
• Use the arrows to select the desired level of volume.
Vibrate
• Press the MODE button again to select the vibrate
icon.
• While the icon is ashing use the arrows to select
vibrate “on” or “off”.
Time and Date
• Press the MODE button to select the time setting.
• When the section is ashing use the UP and DOWN
arrows to adjust the details. Press the MODE button to
move to the next section.
• To exit the settings menu, press and release the
POWER button.

5
SENSORS TO PAGER RECEIVER
Conguring your Sensor to your Receiver
1. Press and release the POWER button.
2. With the keypad unlocked, press the MODE and UP
key at the same time and then release. You will see
‘Code Learning’ on the display.
3. Use the DOWN button to select the zone that you
would like to program (1-16). If the zone is already
occupied, “Use” will show in the display.
4. Use the UP button to select the tune that you want to
play when the zone is activated.
5. Once you have found your preferred tune, activate
your Alert Sensor:
• PIR: wave your hand in front of the Sensor which
will congure the two devices. A small beep will
sound to conrm the conguration.
• Solar Beams: Sensor A - press and release the
POWER button. This will send a signal to your
Receiver for connection. A short beep will sound
on the Receiver to conrm the conguration.
• Probe: pass a metal object (such as a hammer or
key) by the probe, or manually move the probe a
few inches. The receiver emits a short beep.
• Directional Probe:
• Vehicles Entering: Activate the wireless probe
transmitter by pressing the “A” button on the
transmitter board. You should hear a short beep
from the receiver.
• Vehicles Leaving: Activate the wireless probe
transmitter by pressing the “B” button on the
transmitter board. You should hear a short beep
from the receiver.
6. The display will now show “Use” to indicate that the
Sensor has been programmed to that zone.
SET UP.

6
7. If you are using more than one sensor with the Pager,
use the DOWN arrow to select the next zone that you
would like to program.
8. Repeat to programme additional Sensors.
• To exit programming, press and release the power
button.
Conguring more than one Sensor to Receiver
Repeat the process above, selecting a different tune for
each Sensor to help you differentiate which Sensor has
been activated.
ALERT LOG.
RECORDING ALERTS
The Pager can store up to 200 event logs for each of the
zones with time and date stamp.
• Press and release the POWER button.
• To view the log, rst unlock the keypad. Press the
MODE and DOWN buttons at the same time and
release.
• Use the DOWN button to toggle through the 16 zones
to see the total number of activations.
• To view the history of a zone, use the UP button to
toggle back through the history. The most recent
activation will appear rst.
• To clear the event log for any given zone, while on that
zone, press and hold the MODE button for 2 seconds.
The display will read “Record Clearing”.
• Press the MODE and DOWN button at the same time
and release. The memory is now cleared from that
zone.
• To exit the alert log, press and release the POWER
button.

7
ADJUSTMENTS.
FACTORY SETTINGS
To delete all settings and sensor memory, use a small
paper clip to poke through the hole between the POWER
button and the USB charging port. You will feel a small
click when you press the reset button. The display will
default to the original factory setting and no Sensors will
be programmed to the Pager.
DISCONNECTING SENSORS
Removing Sensor Connections
You can reset your Pager to remove all the Sensors that
are connected to it.
• With the keypad unlocked, press the MODE and UP
key at the same time and then release.
• While in programming mode, use the DOWN button
to select the zone you want to disconnect. If the
display reads “Use”, the zone is occupied by a Sensor.
• To delete the Sensor from the zone, press and hold the
MODE button for 2 seconds.
• Press the MODE and DOWN button at the same time
and release. The display will now show “Add” and
“Code Learning” for that zone. You can either program
a Sensor to that zone or continue on by pressing the
DOWN button to move on to the next zone.
LOW BATTERY ALERT IN SENSOR
• If a Sensor has a low battery then the Pager display will
read “Low Battery” when a signal is received from that
Sensor.
• Follow the instructions of the Sensor for advice and
guidance on changing the battery.

8
NEW ZEALAND
www.bealert.co.nz | 0508 242 333
[email protected]
AUSTRALIA
www.bealert.com.au | 1300 588 195
VERSION 1 | 2022