Target ALERT RECEIVER PLUS User manual

ALERT RECEIVER PLUS
INSTRUCTION MANUAL
RE-4K-PLUS-ANZ

2

3
HOW IT WORKS
The Alert Receiver Plus connects to our Alert Sensors.
When the connected Sensors are interrupted or
activated, the Sensor sends a signal to the Alert Receiver
Plus which plays a tone to alert you – so is usually set up
in your house, shed, ofce etc.
There is a range of up to 1.6 km from the Sensors to the
Alert Receiver Plus.
The Alert Receiver Plus allows for the connection of two
accessories which will allow you to hear the alerts at
other points on your property.
The Alert Receiver Plus will receive signals from all of
our Alert Sensors.
ABOUT.
HAVING TROUBLE?
If you’re having trouble with the installation of your kit, or
have questions on how best to congure your kit, check
out the Frequently Asked Questions on our website.
www.bealert.co.nz/FAQ
HELP.
P
I
R
S
e
n
s
o
r
S
o
l
a
r
B
e
a
m
S
e
n
s
o
r
s
P
r
o
b
e
S
e
n
s
o
r
s
Detects heat
motion in front of
the Sensor.
Detects motion
that passes
between Beam
Sensors.
Detects metallic
motion that
passes near
Sensor.
D
i
r
e
c
t
i
o
n
a
l
P
r
o
b
e
S
e
n
s
o
r
s
Detects direction
of metallic motion
that passes near
Sensor.

4
SENSORS TO RECEIVER
If you are connecting Accessories to your Receiver,
follow instructions on page 6-7 before conguring the
Sensors to your Receiver.
Conguring your Sensor to your Receiver
1. On the Receiver, press and hold the MODE button for
3 seconds until the lights on top of the Receiver ash.
2. There are 16 tunes to select from. Press the VOLUME
button until you have selected your preferred tune.
3. Once you have found your preferred tune, activate
your Alert Sensor:
• PIR: wave your hand in front of the Sensor which
will congure the two devices. A small beep will
sound to conrm the conguration.
• Solar Beams: Sensor A - press and release the
POWER button. This will send a signal to your
Receiver for connection. A short beep will sound
on the Receiver to conrm the conguration.
• Probe: pass a metal object (such as a hammer or
key) by the probe, or manually move the probe a
few inches. The receiver emits a short beep.
• Directional Probe:
• Vehicles Entering: Activate the wireless probe
transmitter by pressing the “A” button on the
transmitter board. You should hear a short beep
from the receiver.
• Vehicles Leaving: Activate the wireless probe
transmitter by pressing the “B” button on the
transmitter board. You should hear a short beep
from the receiver.
SET UP.
POWERING YOUR RECEIVER
Connect the power adapter to the Alert Receiver Plus and
then into a power outlet.

5
4. Once congured, press and hold the MODE button
until the lights on the Receiver stop ashing.
5. To test the Kit, activate the Sensor which should
sound on your Receiver.
Conguring more than one Sensor to Receiver
Repeat the process above, selecting a different tune for
each Sensor to help you differentiate which Sensor has
been activated.
INSTALLING SENSORS
Once you have congured your Receiver to your Alert
Sensors your Alert Sensors can be installed at your select
entry point (ie driveway, fence line etc).
Instructions on how to install these sensors will be with
your Sensor Kit, or are available on our website.
INSTALL.
RESET.
DISCONNECTING RECEIVERS
Removing Sensor Connections
• You can reset your Receiver to remove all the Sensors
that are connected to it.
• Press and hold the MODE button until the lights ash.
• Press and hold the MODE and SOUND buttons
together for ve seconds. The lights will ash quickly
then turn off. The Receiver has now disconnected all
Sensors congured to it.
• To recongure Sensors, see page 4.

6
CONFIGURING THE SETTINGS
Before you commence the programming of your
Sensor to Receiver follow these instructions.
On the back of the Receiver, you need to set the DIP
switches to control the actions when a signal is received.
The back of your Receiver Plus looks like this:
• Dip 1 and 2: Alert Receiver Plus notication settings
when your Sensors are activated. We suggest you
leave these alone.
• Dip 3, 4, 5: these are the settings for your connected
accessories. Turn 3, 4 and 5 to ON, by sliding up.
• Dip 6 and 7: Accessories’ settings that determine
the length of time the alert will play for, for the
accessories connected to 3, 4 or 5.
Adjusting the Settings
1. On the Dip Panel, turn on 3, 4 and 5.
2. Now select the length of time that you would like the
alert to play on your accessories.
• 1 Second: 6 is off, 7 is off.
• 5 Seconds: 6 is on, 7 is off.
• 15 Seconds: 6 is off, 7 is on.
• 5 minutes: 6 is on, 7 is on.
CONNECTING ACCESSORIES
1 2 3 4 5 6 7
ON
OFF
Alert Receiver Plus
Lights Sound
Accessories
#1 #2 12VDC
Accessory
alert length

7
CONNECTING ACCESSORIES
• The terminals work with low voltage wiring only.
• The Alert Receiver Plus has two relay outputs (NO,
COM, NC) and a 12 VDC (+ and –) output terminal.
Determining which Terminal to connect to
If you have purchased the Extension Whistle, Siren or Bell
from us, these will be connected to the 12VDC terminals.
Other Accessories: if you are connecting accessories you
have purchased elsewhere, we suggest you speak with an
electrician who will be able to determine which terminal
to connect to, or contact us and we may be able to help.
Connecting to your Alert Receiver Plus
1. To connect lead wires to the terminals, strip off 10 mm
of insulation from the end of the wire.
2. With a small screwdriver, press the orange button to
open the terminal.
3. Insert the bare end of the wire into the terminal
opening, then release the orange button. The terminal
clamps down on the wire.
4. Pull gently on the wire to make sure that your
connection is secure.
5. Now see pages 4-5 to connect your Sensors to the
Receiver.
6. Test your accessory by activating the Sensor that is
connected to your Alert Receiver Plus - your accessory
should now activate.
RELAY 1
NO COM NC
RELAY 2
NO COM NC
12 VDC
+ -

8
NEW ZEALAND
www.bealert.co.nz | 0508 242 333
[email protected]
AUSTRALIA
www.bealert.com.au | 1300 588 195
VERSION 1 | 2022