Tasman Palermo cot User manual

Palermo cot Assembly Instructions
Bassinet Cot Junior Bed
Packaging and instructions
printed on recycled materials
Save these instructions for future reference.
Assembly of this fu rniture is best undertaken by two people.
RECYCLED
Mattress not included
SJC Brands Pty Ltd abn. 58 106 988 578
4-6 Merryvale Rd, MINTO, NSW 2566 p.o. box 5878 MINTO DC, NSW 2566
t. 02 9603 5000 f. 02 9603 7000 e. [email protected]
w. www.tasmaneco.com.au

Headboards x 2
Side panels x 2
Base x 1
50 mm Base and panel
connectore bolts x 12
Metal cross
dowel x 12
Capping screws
x 4
Parts List
Due to the heavy nature of the cot, it is recommended assembly is undertaken by two people.
Warning
Safety Consideration for your Child.
• Follow the manufacturer’s assembly instructions in detail to ensure the safety features of the cot are not compromised.
• ENSURE THE COT IS NOT PLACED TOO CLOSE TO HEATERS, BLINDS, CURTAINS, WINDOWS OR POWER POINTS.
• DO NOT HANG ANYTHING NEARBY WHERE THERE IS A POTENTIAL DANGER OF THE ITEM FALLING INTO THE COT.
• KEEP ANY MEDICATION, STRING, ELASTIC, SMALL TOYS OR SMALL ITEMS SUCH AS MONEY OUT OF REACH FROM
ANY POSITION IN THE COT. It is advisable to keep all items out of your child’s cot to prevent suffocation or strangulation.
• TO PREVENT FALLS, THE BASE OF THE COT SHOULD BE ADJUSTED TO THE LOWEST POSITION BEFORE YOUR
CHILD CAN SIT UP.
Recommended Mattress Size.
• This cot has been manufactured for use with a mattress which measures 690 mm (69 cm) wide x 1300 mm (130 cm)
long x 120 mm (12 cm) (maximum thickness). The width and length are specified because it is IMPORTANT that the gaps
between the mattress and the sides and ends of the cot do not exceed 40 mm when the mattress is pushed to one side or
end, and 20 mm when the mattress is centred in the cot. This is to minimise the risk of a child’s limb becoming caught in
the gap. The thickness of the mattress has been specified to ensure that the depth of the cot is greater than 500 mm with
the mattress base in the lower position to minimise the risk of a child climbing or falling out of the cot.
Safety Consideration for Cot.
• Re-tighten all connector bolts (at least two months after assembling the cot), as some may loosen as the cot settles.
Regulary check all of the connecting bolts, making sure they are tight.
• Regularly check cot for weakness in timber joints and timber panels. If any weaknesses are found, report immediately to
Tasman Eco via: www.tasmaneco.com.au
• Do not use cot if it has been damaged in any way and always use genuine Tasman Eco parts. Contact your nearest
Tasman Eco stockist or original place of purchase for spare parts
2

2Connect the rear panel to the headboards
Fit capping screws to alternate base holes
For newborn babies up to 6 months that cannot sit up attach
the base using the upper bassinet base holes and connnect
the capping screws to lower cot base holes.
For babies over 6 months or babies that can sit up attach
the base using the lower cot base holes and connnect the
capping screws to the upper bassinet base holes.
1
Connect 1 x xed panel to 1 x headboard using 2 x panel connector screws and 2 x metal cross dowels.
Insert the metal cross dowel into top hole of the top rail of the rear panel Insert the connector bolt through the
headboard and into the cross dowel and tighten but leaving 2 mm gap between the rear panel and headboard,
repeat for the bottom hole.
Repeat the process for the other headboard, the cot can then stand on its own
Note: See detail picture below the metal cross dowel must align for the connector bolt to insert into the thread, it
can be adjusted using a screwdriver.
3
Bassinet base
holes
Cot base
holes

3
4
Connect the base to the assembled rear panel and
headboards
Connect The Front Panel
5Tighten All Bolts
Maintaining Your Tasman Cot
Two months after assembling the cot, re-tighten all connector bolts as some may loosen as the cot settles.
panel connector bolts and 4 x
metal cross dowels. Repeat the
steps in section 3 to connect the
front panel.
4
Connect the base to the assembled headboards and rear panel, using 4 x base connector bolts and 4 x metal
cross dowels. (Fit the base in the upper bassinet postion for babies under six months and who cannot sit up, fit the
the base in the lower cot postion for babies over 6 months or who can sit up)
Fit the back of the base first allowing the front of the base to rest on the ground
Insert the metal cross dowel into the back left base hole and insert the connector bolt through the headboard and
into the cross dowel and tighten but leaving a 5 mm gap, repeat for the back right corner.
Lift the front of the base up and into position and repeat above steps
Note: See detail picture below the metal cross dowel must align for the connector bolt to insert into the thread, it
can be adjusted using a screwdriver.
4 x base bolts
4 x rear panel bolts
4 x front panel bolts

Loosen base con-
necting botls approx
3 mm
Loosen base con-
necting botls approx
3 mm
Re-tighten all bolts after removing the front panel
1
2
Converting your cot into a Toddler / Junior Bed
To convert the Palermo into a toddler bed the base must be in the low position
To convert the Palermo into a child’s sofa either base position can be used
To convert the Palermo cot into a Junior bed / Toddler bed / childs sofa remove the front panel
Loosen the 4 x base connector bolts by approx 3 mm to allow the headboards to spread slightly when removing
the front panel
Remove the 4 x front panel connecting bolts and remove the front panel
Re-tighten the 4 x base connecting bolts
5
Palermo Chest and Rascali change table

6
Guarantee & Warranty
Our goods come with guarantees that cannot be excluded under the Australian Consumer Law. You are entitled to a replacement or
refund for a major failur e and for compensation for any other reasonably for eseeable loss or damage. You are also entitled to have
the goods repaired or replaced if the goods fail to be of acceptable quality and the failure does not amount to a major failur e. The
guarantee described below is in addition to the guarantee provided by law.
100% Satisfaction Guarantee
If, within 3 months of the date of purchase of this product, the purchaser is not completely satisfied with this product for any reason,
subject only to the conditions below, the purr chaser can return the product to the place of purchase or to SJC Brands Pty Ltd for a
refund of the full purchase price of this product.
Conditions.
The 100% Satisfaction Guarantee is void and nullified in circumstances where:
1. There are modifications to the product or to parts of the product that were not authorised in writing by SJC Brands Pty Ltd.
2. There is damage to the product and that damage is deemed by SJC Brands Pty Ltd to be caused by incorrect assembly, misuse or
by use or storage outside of the physical or environmental specifications of the product.
2 Year Materials and Workmanship Warranty
If within 2 years of the date of purchase of this product, there is found any defect in materials or workmanship of this product, SJC
Brands Pty Ltd, will replace the product free of charge, subject to the conditions below. The replacement product will be identical to
the originally purchased product wherever possible, though in situations where the identical model is discontinued or out of stock, then
SJC Brands Pty Ltd will replace the product with a model that is functionally equivalent.
This Guarantee is made to the purchaser and/or original owner only. For purposes of this Guarantee, the original owner is considered
to be the person who first makes use of the product. Note: In situations where a person purchases this product for the purpose of
gifting to another, the recipient is considered to be the original owner.
Conditions.
The ‘2 Year Materials and Workmanship Guarantee & Warranty will be void and nullified in circumstances where:
1. The item is improperly assembled or adjusted and or not assembled strictly in accordance with the written instructions provided by
the seller in the box containing the item.
2. There is damage to the product and that damage is deemed by SJC Brands Pty Ltd to be caused by incorrect assembly, misuse or
by use or storage outside of the physical or environmental specifications of the product.
3. There are modifications to the product or to parts of the product that were not authorised in writing by SJC Brands Pty Ltd.
4. The item is transferred, gifted or disposed of by the original owner to another.
Registration and Claims
To be eligible for the above Guarantees, the original owner must register their details online at www.tasmaneco.com.au immediately
upon receipt of the product.
For claims under either the 100% Satisfaction Guarantee or the 2 year Materials and Workmanship Warranty, please email us via our
claims section on our website at www.tasmaneco.com.au or visit the store whe re the pr oduct was purchased.
The product must be returned to SJC Brands Pty Ltd or to the place of purchase with proof of pur
chase, including date and pu
rchase
price.
SJC Brands Pty Ltd abn. 58 106 988 578
4-6 Merryvale Rd, Minto, NSW 2566 p.o. box 5878 Minto DC, NSW 2566
t. 02 9603 5000 f. 02 9603 7000 e. [email protected]
w. www.tasmaneco.com.au