TasmanEco Sleigh Installation guide

TM
RECYCLED
1
Sleigh
Packaging and instructions
printed on recycled materials
Bassinet Cot Junior Bed
(Optional Parts Available)
Chaise Lounge
Save these instructions for future reference.
Assembly of this furniture is best undertaken by two people.
Assembly Instructions
TM
TM
SJC Brands Pty Ltd abn. 58 106 988 578
Unit 4/1 Reaghs Farm Rd, MINTO, NSW 2566 p.o. box 5878 MINTO DC, NSW 2566
t. 02 9603 5000 f. 02 9603 7000 e. [email protected] w. www.tasmaneco.com.au

THIS SIDE UP
THIS SIDE UP
Right Bed Head
Base
Front Adjustable Panel
Rear Fixed Panel
Metal Cross Dowels x 4
(Cot/Bassinet)
Glide Pins x 4
Double Ended Screws x 4
50mm Guard Screws x 2
Allen Key x 1
Screwdriver x 1
Left Bed Head
Connector Bolts x 4
Connector Bolts x 4
Split Washers x 4
2
Parts List
Warning
Safety Consideration for your Child.
• Follow the manufacturer’s assembly instructions in detail to ensure the safety features of the cot are not compromised.
• ENSURE THE COT IS NOT PLACED TOO CLOSE TO HEATERS, BLINDS, CURTAINS, WINDOWS OR POWER POINTS.
• DO NOT HANG ANYTHING NEARBY WHERE THERE IS A POTENTIAL DANGER OF THE ITEM FALLING INTO THE COT.
• KEEP ANY MEDICATION, STRING, ELASTIC, SMALL TOYS OR SMALL ITEMS SUCH AS MONEY OUT OF REACH FROM ANY
POSITION IN THE COT. It is advisable to keep all items out of your child’s cot to prevent suocation or strangulation.
• TO PREVENT FALLS, THE BASE OF THE COT SHOULD BE ADJUSTED TO THE LOWEST POSITION BEFORE YOUR CHILD CAN SIT UP.
• WHEN CONVERTING THE COT TO A JUNIOR BED, THE SIDE RAILS SHOULD BE INSTALLED TO PREVENT FALLS.
Recommended Mattress Size.
• This cot has been manufactured for use with a mattress which measures 750 mm (wide) x 1310 mm (long) x 120 mm
(maximum thickness). The width and length are specied because it is IMPORTANT that the gaps between the mattress and
the sides and ends of the cot do not exceed 40 mm. This is to minimise the risk of a child’s limb becoming caught in the gap.
The thickness of the mattress has been specied to ensure that the depth of the cot is greater than 500 mm with the mattress
base in the lower position to minimise the risk of a child climbing or falling out of the cot.
Safety Consideration for Cot.
• TO ENSURE SAFETY, REGULARLY CHECK ALL OF THE CONNECTING BOLTS, MAKING SURE THAT THEY ARE TIGHT.
Due to the heavy nature of the cot, it is recommended assembly is undertaken by two people.

THIS SIDE UP
THIS SIDE UP
3
Prepare Base
Fit Glide Pins
• Begin by laying the base frame down on the oor. NOTE: The top of the base
is marked “This Side Up” and must be facing DOWNWARDS for this stage of
assembly.
• Insert the metal cross dowels into the four holes in the base. The screw heads
must face upwards. Align the horizontal holes using a screwdriver as shown.
1
2Fit the glide pins and split washers to the four threaded inserts.
Tighten rmly using a screwdriver, but do not overtighten.
DO NOT OVERTIGHTEN

4
3
4
Connect Bed Heads To Base
Fit Double Ended Screws To Unused Holes
• Connect the base to the left bed head. Ensure the sides of the beds heads with
the metal glide pins inserted are facing the correct way for this stage of assembly.
Screw the two sections together using 2 bolts, but do not fully tighten.
• Now connect the right bed head to the base. Screw the sections together using 2
bolts, but do not fully tighten.
When building the Cot, use locating holes “Cot”
When building the Bassinet, use locating holes “Bassinet”
Use the double ended screws to ll the four unused locating holes - one in each corner of the
cot. This is required to prevent the entry of small ngers into these holes.
THIS SIDE UP
THIS SIDE UP
Cot
Bassinet
Cot
Bassinet
Cot
Bassinet
Cot
Bassinet
Sides with glide pins must face
downwards for this stage of
assembly

5
5
6
Connect The Rear (Fixed) Panel
Connect The Front Adjustable Panel
Connect the rear (xed) panel to the bed heads using 2 bolts on either side.
Screw the sections together but do not fully tighten at this time.
Insert the front (adjustable) panel between the left and right bed heads.
NOTE: It is best to have assistance at this stage to avoid damaging the side frames when inserting the glide
pins into the guide channels. The bed head frames will need to be spread apart slightly so the glide pins do
not damage the timber. If required, untighten the connector bolts holding the frames together.
Push the upper glide pins into the top of the guide channels on the bed head frames, then slide the front
panel down slightly on either side. Once the top glide pins are in place, slide the bottom glide pins into the
bottom guide channels.
With these sections now assembled, carefully
lift up and stand the cot on its legs.
Front (Adjustable) Panel
Make sure the badge is
facing the front of the
panel
THIS SIDE UP
THIS SIDE UP
THIS SIDE UP
THIS SIDE UP
TM
TM
TM

6
7
8
Fit The Guard Screws
Tighten All Bolts
Lowering And Raising The Adjustable Panel
Maintaining Your Tasman Eco Cot
IMPORTANT: The guide channels (both sides) must now be secured using the 2 guard screws. The guard
screws prevent damage being caused to the side frames by preventing the front adjustable panel from being
accidentally removed or dislodged from the bed head frames. This is also an important safety feature.
50mm guard screws must
be tted to both sides
The guard screws must be installed to prevent damage to the timber frames
Tighten all connecting bolts.
Do not overtighten or you may
damage the timber.
To clean, wipe down with a soft cloth and soapy water.
Avoid scourers and steel wool as these will damage the nish.
Two months after assembling the cot, re-tighten all connector
bolts as some may loosen as the cot settles.
TM
TM
TM
DO NOT OVERTIGHTEN
Tighten both sides but do
not overtighten
Assembly is now complete
You can lower the front panel with only one hand. First lift it slightly,
then while the panel is raised, push the bottom of the panel
inwards with the side of your leg. Now slowly lower the panel.
To raise the side, simply lift it up with both hands until you hear it
click. The springs will automatically lock back into place.

7
1
2
3
4
5
Converting The Cot Into A Chaise Lounge
To convert your Tasman Eco cot into a
chaise lounge, begin by loosening all
bolts around the cot.
Remove the guard screws.
Remove the adjustable front panel
from the bed head frames.
Remove the glide pins and split
washers from the bed head
frames. (Store these parts in a
safe place).
Retighten the bolts. (Do not overtighten).
Place a throw rug over the
mattress, add a few colourful
pillows and your child has their
very own chaise lounge where they
can read, rest or play.
TM
TM
Loosen both sides
Tighten both
sides

8sleigh_ins_0412
TM
TM
SJC Brands Pty Ltd abn. 58 106 988 578
Unit 4/1 Reaghs Farm Rd, MINTO, NSW 2566 p.o. box 5878 MINTO DC, NSW 2566
t. 02 9603 5000 f. 02 9603 7000 e. [email protected] w. www.tasmaneco.com.au
TM
Would you like us to assemble your Tasman Eco furniture for you?
It’s a great way to enjoy the benets of your furniture with a minimum of fuss. And you know the assembly will be
done right - in fact, we guarantee it. If there is any damage resulting from our assembly service - it’s automatically
our responsibility. Service is prompt, reliable, and friendly.
Booking
This service is available only in the Sydney metro area. For more information, including pricing, see our website
www.tasmaneco.com.au. Or just call 02-9603-5000 during business hours to arrange a time and a day, so one of
our assembly professionals can come to your home to assemble your newly purchased Tasman Eco furniture.
Furniture Assembly Service
The Tasmaneco Guarantee
Our goods come with guarantees that cannot be excluded under the Australian Consumer Law. You are entitled to a replacement or refund for
a major failure and for compensation for any other reasonably foreseeable loss or damage. You are also entitled to have the goods repaired or
replaced if the goods fail to be of acceptable quality and the failure does not amount to a major failure. The guarantee described below is in
addition to the guarantee provided by law.
100% Satisfaction Guarantee
If, within 3 months of the date of purchase of this product, the purchaser is not completely satised with this product for any reason, subject
only to the conditions below, the purchaser can return the product to the place of purchase or to SJC Brands Pty Ltd for a refund of the full
purchase price of this product.
Conditions.
The 100% Satisfaction Guarantee is void and nullied in circumstances where:
1. There are modications to the product or to parts of the product that were not authorised in writing by SJC Brands Pty Ltd.
2. There is damage to the product and that damage is deemed by SJC Brands Pty Ltd to be caused by incorrect assembly, misuse or by use or
storage outside of the physical or environmental specications of the product.
5 Year Materials and Workmanship Guarantee
If within 5 years of the date of purchase of this product, there is found any defect in materials or workmanship of this product, SJC Brands
Pty Ltd, will replace the product free of charge, subject to the conditions below. The replacement product will be identical to the originally
purchased product wherever possible, though in situations where the identical model is discontinued or out of stock, then SJC Brands Pty Ltd
will replace the product with a model that is functionally equivalent.
This Guarantee is made to the purchaser and/or original owner only. For purposes of this Guarantee, the original owner is considered to be the
person who rst makes use of the product. Note: In situations where a person purchases this product for the purpose of gifting to another, the
recipient is considered to be the original owner.
Conditions.
The ‘5 Year Materials and Workmanship Guarantee’ will be void and nullied in circumstances where:
1. The item is improperly assembled or adjusted and or not assembled strictly in accordance with the written instructions provided by the
seller in the box containing the item.
2. There is damage to the product and that damage is deemed by SJC Brands Pty Ltd to be caused by incorrect assembly, misuse or by use or
storage outside of the physical or environmental specications of the product.
3. There are modications to the product or to parts of the product that were not authorised in writing by SJC Brands Pty Ltd.
4. The item is transferred, gifted or disposed of by the original owner to another.
Registration and Claims
To be eligible for the above Guarantees, the original owner must register their details online at www.tasmaneco.com.au immediately upon
receipt of the product.
For claims under either the 100% Satisfaction Guarantee or the 5 year Materials and Workmanship Guarantee, please email us via our claims
section on our website at www.tasmaneco.com.au or visit the store where the product was purchased.
The product must be returned to SJC Brands Pty Ltd or to the place of purchase with proof of purchase, including date and purchase price.