Tatung V32MAAK User manual

i
EnglishFrançaisItaliano
Deutsch
Español
Nederlands
V32MAAK-ET1-01EN 10/11/2007_ver.A
Table of Contents
BEFORE GETTING STARTED.....................................................................................1
OPERATING SAFETY .....................................................................................................1
CONNECTING ...............................................................................................................2
Power supply..........................................................................................................2
Point of use ............................................................................................................2
ADDITIONAL SAFETY INSTRUCTIONS ..............................................................................3
Precautions ............................................................................................................3
INTRODUCTION ...........................................................................................................4
BOX CONTENTS ...........................................................................................................4
FURTHER FEATURES.....................................................................................................5
OVERVIEW OF THE TV ..................................................................................................6
Indicator..................................................................................................................6
Function Keys.........................................................................................................7
Connections ...........................................................................................................8
OVERVIEW OF THE REMOTE CONTROL...........................................................................9
SETTING UP ...............................................................................................................11
CONNECTIONS ..........................................................................................................11
Connecting video devices via AV cables..............................................................11
Connecting a video device via HDMI - HDMI ......................................................12
Connecting a PC via VGA cable ..........................................................................13
WATCH ING TV............................................................................................................14
Turning the LCD Display On and Off ...................................................................14
Initial Power on.....................................................................................................16
Source Buttons.....................................................................................................17
Volume Control.....................................................................................................18
Setting the Sleep Timer........................................................................................18
ARC - Aspect Ratio Control..................................................................................19
APC - Automatic Picture Control..........................................................................19
NICAM/A2 (IGR) BROADCAST SELECTION..................................................................20
GENERAL CONTROLS & ADJUSTMENT ................................................................21
HOW TO CONTROL ON-SCREEN DISPLAY (OSD) ..........................................................21
VIEWING THE ON-SCREEN DISPLAY (OSD) ..................................................................22

ii
PICTURE SETTING ......................................................................................................23
SOUND SETTING.........................................................................................................24
SERVICE IN ANALOGUE TV ..........................................................................................25
Service Management ...........................................................................................26
Rename/Sort/Delete.............................................................................................26
PREFERENCES ...........................................................................................................27
Child Lock.............................................................................................................28
On Timer...............................................................................................................29
CONNECTIVITY:PC SETTING.......................................................................................30
INFORMATION .............................................................................................................32
RESET .......................................................................................................................33
TELETEXT ..................................................................................................................34
TELETEXT OPERATION.............................................................................................34
TELETEXT PAGE SELECTION ....................................................................................35
USEFUL FEATURES FOR TELETEXT ...........................................................................35
TROUBLESHOOTING................................................................................................37
SAFETY AND REGULATORY INFORMATION .........................................................40
REPAIR ......................................................................................................................40
NOTES FOR SERVICE ENGINEERS................................................................................40
ENVIRONMENTAL CONDITIONS .....................................................................................40
PC INPUT PRESET TIMING TABLE..........................................................................41
SPECIFICATIONS.......................................................................................................42

1
EnglishFrançaisItaliano
Deutsch
Español
Nederlands
V32MAAK-ET1-01EN 10/11/2007_ver.A
Before Getting Started
Please read through this section carefully and follow the instructions to maximize
the reliable operation and lifetime of your LCD display. Always keep these
instructions handy and close by your LCD display. Keep the instructions and the
packaging so that if you sell or give away your LCD display you can give them to the
new owner.
Conventions used in this manual
WARNING Information to prevent injury to yourself when trying to
complete a task.
CAUTION Information to prevent damage to the components when
trying to complete a task.
Operating Safety
•Never open the housing of the LCD display/power supply! When the housing is
open, there is a danger of injury from electric shock!
•Do not insert any objects through the slots and openings of the monitor. This may lead
to an electrical short-circuit or even fire resulting in damage to your LCD display.
•Slots and openings in the LCD display are for ventilation purposes. Do not cover
these openings, as this may lead to overheating.
•Do not allow children to play unattended with electrical equipment. Children may
not always correctly recognize danger.
•This LCD display is intended for personal use only. It is not intended for
commercial use in a heavy industry environment.
•An injury hazard exists if the display breaks. Wear protective gloves to pack the
broken parts and send them to your service centre for proper disposal. Then wash
your hands with soap, because it is possible for chemicals to escape.
•Never exert pressure on the display. This could break the monitor.
•Do not touch the display with your fingers or with sharp objects to avoid damage.
•No naked flame sources, such as lighted candles, should be placed on the
apparatus.

2
Contact the Call Centre immediately in any of the following situations. Do NOT
plug in or switch on your display:
•If the power cable/power supply overheats or is damaged
•If liquid is leaked into the monitor
•If the LCD display is dropped or the housing damaged
Connecting
Observe the following instructions to connect your LCD display properly:
Power supply
•Do not open the power supply housing. An open housing presents
a lethal hazard from electrical shock. There are no parts inside to
be cleaned or serviced.
•Operate your LCD display only with grounded outlets with AC 100-240V/ 50-60 Hz. If
you are not sure about the power supply at your location, check with your power
company.
•Use only the power supply and power connection cable provided.
•For additional safety we recommend use of a surge protector to protect your LCD
display from damage resulting from voltage surges or lightning.
•To remove the LCD display from the power supply, disconnect the plug from the
AC outlet.
•Where the main plug is used as the disconnect device, the power outlet must be
in the vicinity of your LCD display and within reach of the power cables. DO NOT
stretch the power cables tightly to reach a power outlet.
•You should arrange the LCD display cables in a manner so that no one can trip
over or step on them.
•To avoid damage to cable do not place any objects or furniture on the cable.
•Do not defeat the safety purpose of the polarized or grounding-type plug. If the
provided plug does not fit into your outlet, consult an electrician for replacement of
the obsolete outlet.
Point of use
•Keep your LCD display and all units connected to it away from moisture and avoid
dust, heat and direct sunlight. Failure to observe these instructions can lead to
malfunctions or damage to the LCD display.
•Place and operate all units on a stable, level and vibration-free surface in order
to avoid the LCD display from falling.

3
EnglishFrançaisItaliano
Deutsch
Español
Nederlands
V32MAAK-ET1-01EN 10/11/2007_ver.A
Additional Safety Instructions
When using any electronic equipment, basic safety precautions should always be
taken. Following the guidelines below can reduce the risk of fire, electric shock and
injury to person:
•Do not use this product including TV set and remote near water (e.g. near a
bathtub, wash bowl, kitchen sink or laundry tub, in a wet basement or near a
swimming pool).
•Use only the power cord indicated in this manual. Do not dispose of batteries in a
fire. They may explode. Check with local codes for possible special disposal
instructions.
•Keep batteries away from children at all times.
Precautions
•There are no parts which can be serviced or cleaned inside of the TV
display housing.
You can increase the life of your LCD display by taking the following precautions:
•Before cleaning always disconnect the power line and all connection cables.
•Do not use any solvents, caustic or gaseous cleaning agents.
•Clean the display with a soft, lint-free cloth.
•Ensure that no water droplets remain on the screen. Water can cause permanent
discoloration.
•Do not expose the screen to bright sunlight or ultraviolet radiation.
Information on Disposal of Waste Electrical and Electronic Equipment
This symbol on the product or in the instructions means that your
electrical and electronic equipment should be disposed at the end of
its life cycle separately from your household waste. There are
separate collection systems for recycling in the EU. For more
information, please contact the local authority or your retailer where
you purchased the product.

4
Introduction
Thank you for purchasing our LCD display. We thank you for your confidence in our
products and are pleased to greet you as a new customer.
We focus on great features, ease of use and reliability in manufacturing your LCD
display.
Service
Your display comes with a one-year warranty; this is in addition to your statutory
rights. This manual contains a separate chapter on Troubleshooting on page 37.
Performance Characteristics
Advantages relating to CRT (cathode ray tube) display:
•Less space required
•Lighter weight
•Lower power consumption
Box Contents
Please check that you have received the following items with your LCD display. If
any following items are missing, please contact your nearby retailer
User’s Manual Remote Control &
Batteries(AAA X2)
AC Power Cord
USER’S MANUAL
LCD - TV

5
EnglishFrançaisItaliano
Deutsch
Español
Nederlands
V32MAAK-ET1-01EN 10/11/2007_ver.A
Further Features
¾The connection terminals include RF IN, D-SUB, HDMI1, HDMI2, SCART 1
(CVBS, RGB), SCART 2 (CVBS, S-VIDEO, RGB), COMPONENT, CVBS and
S-VIDEO.
¾Easy-to-use remote control, and OSD (On-Screen Display) menu.
¾ARC (Aspect Ratio Control) settings include Auto image, 4:3, 16:9, 14:9,
Panoramic, and Zoom.
¾APC (Automatic Picture Control) settings include Normal, Cinema, and Dynamic.
¾A.P.S. (Auto Programming System) for automatic TV channel tuning.
¾TELETEXT function is available.
¾Child lock function is available.
¾Built-in dual channel speakers.
¾Built-in NICAM/A2 (IGR) sound decoder for stereo and bilingual listening.
¾Automatic sleep timer ranges from 10 to 120 minutes in 10-minute increments.
¾Provided component video input for high definition TV program, resolution up to
720p, 1080i.

6
Overview of the TV
Indicator
Indicator
Indicator Lighting Status:
OFF (No power input) Off
Standby passive Red
Power on (TV / Video / PC mode) Green
Standby active (only available in PC mode) Amber
A green indicator lights when the power is on and an amber indicator lights
when in the standby PC mode. A red indicator lights when in standby mode
passive.
Remote Control Sensor
Remote control sensor
Indicator

7
EnglishFrançaisItaliano
Deutsch
Español
Nederlands
V32MAAK-ET1-01EN 10/11/2007_ver.A
Function Keys
Function Keys (on the display panel):
EXIT/ ARC •Select the TV display mode to switch Auto Image / Panoramic
/ 16:9 / 14:9 / 4:3 / Zoom.
•When in OSD (On-Screen Display)* menu, press EXIT / ARC
to close the OSD menu
- VOLUME + •Increase or decrease the volume.
▼CHANNEL▲•Change channels.
MENU •Display the OSD main menu.
•Return to previous menu when in OSD menu.
SOURCE •Select input source TV / SCART1 / SCART2/ SCART2S/
CVBS/ S-VIDEO/YUV/ HDMI 1/ HDMI 2/ VGA.
•When OSD MENU is invoked, it will function as the "OK" key
to setup a function or enter a sub-menu.
POWER •Shift on or off the TV.
•When the status of indicator is off, press POWER on the
panel to
enable this LCD TV.
NOTE:
Function Keys control your TV’s basic features, and you may use these to adjust on-screen
display (for example, items in the main menu or sub-menu). To use more advanced features,
you must use the remote control.

8
Connections
NOTE:
Audio out L/R: The level of audio output cannot be changed using the volume control on
your display. This connector should be used with an external audio amplifier that can be used
to control the volume.