TDC USA Rocking Chair Set 22104 User manual

Made in China
The owner’s manual contains important safety information as well as assembly, use and
maintenance instructions. Keep the packaging and bags away from children and dispose
of all packaging properly before use. Keep this manual for future reference.
3 Piece
Rocking Chair Set
Assembly Instructions

3
PLEASE DO NOT
RETURN THIS
PRODUCT
TO THE STORE
We will be happy to correct any problems that you may
have, or answer any of your questions regarding the
purchase of this product. Please contact us at our Toll
Free customer service number 1-800-599-8898 for any
assistance and replacement parts. Thank You.
Dist. by TDC USA, Inc. Faireld, NJ 07004
©2021 All Rights Reserved.
Made in China
Item 22104
www.tdcusainc.com
Warnings
· CHOKING HAZARD - Small parts. Not suitable for children under 36 months. The
product contains small parts, keep children away when assembling.
· ADULT ASSEMBLY REQUIRED.
Always remove protective material and poly bags and dispose before assembly.
WARNING!
• Keep all children and pets away from assembly area.
Children and pets should be supervised when they
are in the area of the product construction.
• Some parts may contain sharp edges. When
assembling and using this product, basic safety
precautions should always be.
• Please read all the instructions and warnings before
assembling. In order to make the whole product
adjust to the best, please install all the screws on
the product and tighten all the screws after adjusting
the product which can stand on the oor even. Not
intended for commercial use.
• Check all bolts for tightness before use.
• IMPORTANT - check and tighten bolts often to keep
them secure

4 5
Parts List Chair Instructions (x2)
K
M
C
A
K
M
AC
Step 1:
Set the Armrest (A) on a soft,
non-abrasive surface.
Insert one Bolt M6x15 (K)
with Washer (M) through the
eyelet found at the bottom-
left corner of Chair Back (C)
and into the bolt-threading
found at the center-back of
Armrest (A). Do not tighten
bolts down until assembly
of the chair is complete.
Step 2:
Turn thepreviouslyassembled
parts over as illustrated here.
Insert one Bolt M6x15 (K) with
Washer (M) through the eyelet
found underneath armrest of
part A and into bolt-threading
on the side of Chair Back (C).
Step 3:
Set the Armrest (B) on a soft,
non-abrasive surface and
place previously assembled
parts on top of it as illustrated
here. Insert one Bolt M6x15 (K)
with Washer (M) through the
eyelet found at the bottom-
right corner of Chair Back (C)
and into the bolt-threading
found at the center-back of
Armrest (B).
K
M
C
B
A (x2)
Armrest
B (x2)
Armrest
C (x2)
Chair Back
D (x2)
Chair Seat
E (x2)
Table Leg
F (x1)
Support
G (x1)
Table
H (x1)
Glass
I (x2)
Seat Cushion
K (x16)
M6x15 Bolt
L (x8)
M6x25 Bolt
M (x24)
Washer
AA (x1)
Hex Key

6 7
Chair Instructions (x2)
Step 4:
Turn the previously assembled parts over as illustrated here. Insert one Bolt M6x15
(K) with Washer (M) through the eyelet found underneath armrest of part B and
into bolt-threading on the opposite side of Chair Back (C).
Step 5:
Place Chair Seat (D) in between Armrests (A&B).
Insert two Bolts M6x25 (L) with Washers (M) through the eyelets found underneath
the left-side of Chair Seat (D) and into the bolt-threading found on the horizontal
bar of Armrest (A). Follow this step to connect Chair Seat (D) to the horizontal bar
of Armrest (B). Tighten all bolts left loose throughout assembly process using Hex
Key (AA). Follow these steps to assemble the second chair for this set.
Chair Instructions (x2)
K
M
B
C
A
B
D
L
M

8 9
Table Instructions
Step 1:
Remove Glass (H) from Table (G) carefully and set it aside until assembly is
complete. Set the Table (G) upside-down on a soft, non-abrasive surface.
Insert one Bolt M6x15 (K) with Washer (M) through the eyelets at the ends of Leg
(E) and into the bolt-threading found at the corners [underneath] of Table (G). Do
not tighten bolts down until assembly of the table is complete. Follow this step
to assemble the second Table Leg (E) on the opposite side of Table (G).
Step 6:
Place Seat Cushions (I) on top of Chair Seats (D) when assembly of both chairs is
complete. The chairs are ready to be used.
Chair Instructions (x2)
K
M
G
E
I

10
Step 3:
Turn the table right-side
up. Carefully place Glass
(H) into the center of Table
(G) rim. The table is ready
to be used.
Step 2:
Insert two Bolts M6x15 (K) with Washers (M) through eyelets at either end Table
Support (C) and into the bolt-threading found on the horizontal bar of each Table
Leg (E). Tighten all bolts left loose throughout assembly process using Hex Key (AA).
Table Instructions
E
F
MK
M
K
E
H
.

Dist. by TDC USA, Inc. Faireld, NJ 07004
©2021 All Rights Reserved. Made in China.
Item #22104
Questions and Comments
1-800-599-8898 (9 am - 5 pm EST)
www.tdcusainc.com
3 Piece
Rocking Chair Set