Belson Outdoors BST-01 User manual

111 North River Road
North Aurora, IL 60542
Phone: [phone]
Fax: [phone]
[email protected]
Model # BST-01 Instructions Sheet
www.belson.com
BISTRO PICNIC TABLE

www.belson.com
BEFORE ASSEMBLY, PLEASE MAKE SURE ALL COMPONENTS ARE INCLUDED.
J - TABLE TOP
( 1 ) - ONE TABLE TOP
N - SEAT
( 4 ) - FOUR SEATS
FP - FASTENER PACK
( 1 ) - ONE FASTENER PACK
R - TABLE CENTER
( 2 ) - TWO TABLE CENTERS
H - TABLE LEG
( 4 ) - FOUR TABLE LEGS
Q - SEAT SUPPORT
( 4 ) - FOUR SEAT SUPPORTS

www.belson.com
1 - 3” PHILLIPS DRIVE BIT
2 - 9/16” SOCKET WRENCH
ALSO NEEDED FOR THIS ASSEMBLY WILL BE THE FOLLOWING MATERIALS:
8 - 3/8” X 4-1/2” HEX HEAD BOLT
BEFORE ASSEMBLY, PLEASE MAKE SURE ALL FASTENERS ARE INCLUDED.
16 - 3/8” FLAT WASHER
8 - 3/8” NYLON LOCK NUT
8 - #12 X 3” FLAT HEAD PHILLIPS SCREW
64 - #12 X 1” PAN HEAD PHILLIPS SCREW

www.belson.com
STEP #1:
SLIDE ( 1 ) ONE TABLE CENTER ONTO EACH END OF THE TABLE LEG AS SHOWN ABOVE. USE ( 1 )
ONE 3/8” X 4-1/2” HEX HEAD BOLT AND ( 1 ) ONE 3/8” FLAT WASHER ALONG WITH ( 1 ) ONE 3/8” FLAT
WASHER AND ( 1 ) ONE 3/8” NYLON LOCK NUT PER HOLE TO SECURE.
DO NOT TIGHTEN BOLTS COMPLETELY. THIS WILL BE DONE AT A LATER STEP.
3/8” x 4-1/2” HEX
HEAD BOLT
3/8” FLAT
WASHER
3/8” FLAT WASHER
3/8” NYLON LOCK NUT

www.belson.com
STEP #2:
SLIDE THE REMAINING ( 3 ) THREE TABL LEGS IN TO THE TABLE CENTERS. USE ( 1 ) ONE 3/8”
X 4-1/2” HEX HEAD BOLT AND ( 1 ) ONE 3/8” FLAT WASHER, ALONG WITH ( 1 ) ONE 3/8” FLAT
WASHER AND ( 1 ) ONE 3/8” NYLON LOCK NUT PER HOLE TO SECURE.
DO NOT TIGHTEN BOLTS COMPLETELY. THIS WILL BE DONE AT A LATER STEP.
3/8” x 4-1/2” HEX
HEAD BOLT
3/8” FLAT WASHER
3/8” FLAT WASHER
3/8” NYLON LOCK NUT

www.belson.com
STEP #3: PLACE THE TABLE TOP UPSIDE DOWN ONTO A PIECE OF CARDBOARD OR ANOTHER SOFT
SURFACE, TO PROTECT IT DURING INSTALLATION. PLACE THE LEG ASSEMBLY ONTO THE TABLE
TOP AS SHOWN ABOVE. ALIGN THE PRE-DRILLED HOLES IN THE TABLE LEGS WITH THE PILOT
HOLES IN THE TABLE TOP. USE ( 1 ) ONE #12 X 1” PAN HEAD SCREW PER HOLE TO SECURE.
BE SURE TO TIGHTEN ALL SCREWS AND BOLTS AFTER COMPLETING THIS STEP.
#12 X 1” PAN HEAD
PHILLIPS SCREW

www.belson.com
STEP #4:
WHILE THE TABLE IS UPSIDE DOWN, ALIGN THE PRE-DRILLED HOLES IN THE TABLE LEG TO THE
PILOT HOLES IN THE SEAT SUPPORT, AS SHOWN ABOVE. USE ( 1 ) ONE #12 X 3” FLAT HEAD SCREW
PER HOLE TO SECURE.
DO NOT TIGHTEN SCREWS COMPLETELY. THIS WILL BE DONE IN A LATER STEP.
#12 X 3” FLAT HEAD
PHILLIPS SCREW

www.belson.com
STEP #5:
WHILE THE TABLE IS UPSIDE DOWN, ALIGN THE PRE-DRILLED HOLES IN THE SEAT TO THE PILOT
HOLES IN THE SEAT SUPPORT AND THE TABLE LEG AS SHOWN ABOVE. USE ( 1 ) ONE #12 X 1”
PAN HEAD SCREW PER HOLE TO SECURE.
BE SURE TO TIGHTEN ALL LOOSE SCREWS AFTER COMPLETING THIS STEP.
#12 X 1” PAN HEAD
PHILLIPS SCREW

www.belson.com
STEP #6:
TURN THE TABLE OVER ON TO ITS LEGS, PLEASE USE CAUTION FOR THE TABLE WEIGHS
APPROXIMATELY 200 POUNDS.