Technaxx TX-100 User manual

Technaxx
®
* User Manual
Car Alarm with charging function TX-100
& Remote Control for monitoring of vehicle interiors via PIR
motion detection sensor
The manufacturer Technaxx Deutschland GmbH & Co.KG hereby declares
that this device, to which this user manual belongs, complies with the essential
requirements of the standards referred to the Directive RED 2014/53/EU. The
Declaration of Conformity you find here: www.technaxx.de/ (in bar at the
bottom “Konformitätserklärung”). Before using the device the first time, read
the user manual carefully.
Service phone No. for technical support: 01805 012643 (14 cent/minute from
German fixed-line and 42 cent/minute from mobile networks).
Free Email: supp[email protected]
This device has a rechargeable battery. It must be fully charged before first
use. NOTE: Charge the battery of the device every 2–3 month if it is not used!
Keep this user manual for future reference or product sharing carefully. Do the
same with the original accessories for this product. In case of warranty, please
contact the dealer or the store where you bought this product.
Warranty 2 years
Enjoy your product * Share your experience on Amazon
Features
12–24V rechargeable car alarm for the cigarette lighter socket
Has 2 USB charging ports with 5V/1A output power each
Automatic alarm triggering at motion detection by PIR sensor
(Passive Infrared sensor for physical movement detection for the
car's interior)
Built-in 450mAh battery for ~6 days standby time ensures alarm
triggering even when engine is switched off
Built-in alarm siren with 110dB
Remote control to activate and deactivate the alarm
LED status indicator
Over-current protection 2.8A & short circuit protection
Easy handling and installation

Technical Specification
Detecting distance ~3m car interior (without obstacles (e.g. rear
wall in trucks)
Detecting range 120° cone angle
Distance IR remote control ~8m (open field)
Alarm time 2 minutes maximum
USB output charging 2x 5V/1A
Power Built-in rechargeable 450mAh lithium polymer
battery 4.2V
Charging time ~3–4 hours
Working time ~5 days (by alarm 5-times a day)
Standby time ~6 days
Input voltage DC 12–24V (cigarette lighter socket)
Charging current 65mA
Operating current 26mA
Transmission frequency
433.92 MHz
Frequency type ASK
Radiated output power maximum 20mW (by pressing remote
control button, not continuously)
Material ABS
Weight / Dimensions
car alarm 44g / (L) 3.2 x (W) 3.2 x (H) 11.5cm
Weight / Dimensions
remote control 10g / (L) 5.3 x (W) 3.1 x (H) 1.0cm
Package Contents Car Alarm with charging function TX-100, Remote Control (with button cell battery
CR2032 3V), User Manual

Product overview
Car Alarm / Charger Remote Control
1
PIR (Motion detection)
4
Indicator (confirmation)
2
USB charging slot
(2x 5V71A)
5
Remote button
(activate/deactivate)
3
Siren
6
Battery compartment of remote
control

Charge the product
First time using, plug device in the 12–24V cigarette socket to
power on the device. Charge the device for 3–4hours before using it.
You can also use an external charger* (*not included) to charge the
device.
Note: In some cars the cigarette lighter socket is off power when the
engine of the car is not started. So please start your car to power the
cigarette lighter socket.
Get started
After inserting to the cigartte lighter socket, three operations
will happen at the same time:
1. After inserting the device there is a short "beep". The PIR sensor
is armed.
2. You have to pair the device with the included remote once to be
sure that the remote is only paired with your car alarm. This is only
possible in the first 5 seconds after you plugged the device into the
cigarette lighter socket. Press and hold the button on the remote
while the first 5 seconds until you here 4x “beep”. Now the remote is
paired with your car alarm.
3. The red light of the device inside the dome turns on. It indicates
the battery is charging (Charging current 65mA). The red light will
turn off when the device is fully charged.

Remote Control & Functions
Activate (Arm)
PIR sensor can be activated by pressing the remote button shortly or
inserting the device into a cigarette lighter socket. Once PIR sensor
is activated, it takes about 5 seconds until the device is armed.
When armed the blue light flashes every 5 seconds. After human
action is detected, blue light flashes quickly each second and the
siren is noising loudly. When the alarm will work continuous for two
minutes (working current under alarm status is 26mA)
Deactivate (Disarm)
To deactivate the PIR sensor and turn off the alarm sound, press the
button on the remote shortly. You will hear 2x short “beep” and the
blue light stops flashing. The max. distance to disarm the device
before getting back into the car is ~8m on open field.
Shut OFF device
If you press the remote button long (3-4 seconds) you will hear one
short “beep”, and one long “beep” sound. After that the device’s
battery is turned off. Not just the PIR sensor is shut off, the whole
device is shut off for long time no use or for transportation.
All indicator turn off, except the charging indicator (red) when the
device is still plugged into an active cigarette lighter socket. The
device can only be activated/ armed when you plug it into the
cigarette lighter socket again. The remote is not working when
device is shut off.
Note: It is possible to operate the remote from outside the closed
car through the window. The remote gives an acoustic and a
visual feedback by pressing the button

USB charger function
If the device is powered from a car cigarette lighter socket, you can
connect the USB charger port to your mobile phone with a USB
cable* (*not included). The device now is working as mobile phone
charger. It is also possible to charge other devices via USB.
Note: Maximum output of USB is 2x 1A.
Dual Mode
If you have two car alarms you can handle them with one remote. No
need to take two remotes with you. For example you can store one
car alarm in the luggage compartment and the other car alarm in the
centre console in the front of the car.
But before installing you have to pair both devices with the remote.
That needs to be done by inserting both devices at the same time to
cigarette lighter socket. Now both devices are for 5 seconds in
pairing mode.
In the first 5 seconds press and hold the button on the remote for
pairing both devices with the remote. 4x “beep” will confirm the
pairing. For pairing also look under Get started point 2.
Attention: You cannot pair the devices one after another. It is
necessary to plug the devices in at the same time to use one remote
control.
Change remote control battery
When the remote control does not feedback with acoustic or visual
behavior after pressing the button, change the battery (CR2032).
For changing the battery use a coin to open the battery compartment.
Turn the cover on the backside of the remote control left to open and
right to close. Insert the battery. After inserting you should see the
“plus” pole of the battery. Now close the compartment.

Warnings
To prolong the life of this device, pull it out when starting the
engine of the car.
Do not remove any cover to avoid the risk of an electric shock or
other damages.
Do not attempt to disassemble the device, it may result in
short-circuit or even damage.
Do not drop or shake the device, it may break internal circuit
boards or mechanics.
Keep the device in dry and ventilated environment. Avoid high
humidity and high temperature.
Do not expose this unit to rain or moisture, to reduce the risk of
fire or electrical shock. The device should not be exposed to dripping
or splashing.
Do not install the device near any heat source, such as radiators,
or other equipment that produces heat. Keep the device away from
direct sunlight.
Keep the device away from little children.
Security and Disposal Hints for Batteries: Hold children off batteries.
When a child swallowed a battery go to a doctors place or bring the child
into a hospital promptly! Look for the right polarity (+) and (–) of batteries!
Always change all batteries. Never use old and new batteries or batteries of
different types together. Never short, open, deform or load up batteries!
Risk of injury! Never throw batteries into fire! Risk of explosion!
Hints for Environment Protection: Packages materials are raw materials
and can be recycled. Do not disposal old devices or batteries into the
domestic waste. Cleaning: Protect the device from contamination and
pollution (use a clean drapery). Avoid using rough, coarse-grained
materials or solvents/aggressive cleaner. Wipe the cleaned device
accurately. Important Notice: Should battery fluid leak from a battery, wipe
the battery case with a soft cloth dry. Distributor: Technaxx Deutschland
GmbH & Co.KG, Kruppstr. 105, 60388 Frankfurt a.M., Germany