Technexion Tc-1010-apl User manual

3.1 Cut-out Dimensions

TC-1010-APL / TC-1560-APL

Quickstart Guide

3 Installaon Instrucons

This secon describes the mounng procedures for TC series device. The material in the mounng area must provide suﬃcient strength for support of this HMI.

3.2 VESA Mounng

This device is compable with VESA MIS-D Standard 100*100mm. There are 4 VESA MIS-D (M4) mounng holes on the rear side of the device. M4 screws with at least

6mm head-to-p length are required to secure this device.

3.3 Rear Mounng

There are 8 (TC-1010-APL) / 14 (TC-1560-APL) mounng clips required for rear mounng.

INNOVATORS OF TECHNOLOGY

TC-1010-APL TC-1560-APL

2 Dimensions

1 Safety Precauons

Thank you for purchasing a TechNexion TC series device. This installaon guide will be helpful in the installaon, wiring and inspecon of your TechNexion embedded

fanless box PC. Before using the product, please read this guide to ensure correct use. You should thoroughly understand all safety precauons before proceeding with

the installaon, wiring, and operaon. Place this instrucon sheet in a safe locaon for future reference. The following suggesons will help you.

• Keep the device dry. Precipitaon, humidity, and all types of liquids or moisture can contain minerals that will corrode electronic circuits. If your device does get wet,

allow it to dry completely.

• Do not use or store the device in dusty or dirty areas. Its parts and electronic components can be damaged.

• Do not store the device in hot areas. High temperatures can shorten the life of electronic devices, damage baeries, and warp or melt certain plascs.

• Do not store the device in cold areas. When the device returns to its normal temperature, moisture can form inside the device and damage electronic circuit boards.

• Do not aempt to open the device. This product is designed for speciﬁc applicaons and needs to be installed by qualiﬁed personnel.

• Do not drop, knock, or shake the device. Rough handling can break internal circuit boards and ﬁne mechanics.

• Do not paint the device. Paint can clog the parts and prevent proper operaon.

• Unauthorized modiﬁcaons or aachments could damage the device and may violate regulaons governing radio devices.

• Do not touch any internal or exposed parts of the device as electrical shock may result.

• Do not open the device while power is on. Otherwise electrical shock may result.

• Do not use harsh chemicals, cleaning solvents, or strong detergents to clean the device.

• Be sure the venlaon holes are not obstructed during operaon. Otherwise malfuncon may result due to bad venlaon or overheang.

These suggesons apply equally to your device, baery, charger, or any enhancement. If any device is not working properly, take it to the nearest authorized service

facility for service.

•Make sure that the available power source matches the required input power of the device. Failure to observe this cauon may result in electric shock or ﬁre.

•Do not power the unit by DC input when you apply power over the PoE (RJ45).

1.1 Storage and Installaon

1.2 Wiring

1.3 Maintenance and Inspecon

Unit : mm

1 2

TC-1010-APL TC-1560-APL

53 263.46

182.1

9.5

154.6

407.11

257.42

59.05

137.2

229.5

165

246 375

235

3.4 Surface Mounng

There are 10 (TC-1010-APL) / 16 (TC-1560-APL) mounng holes (M4) on the rear side of the device required for surface mounng. M4 screws with at least 6mm

head-to-p length are required to secure this device.

without the prior wrien permission of TechNexion Ltd.

• No warranty of accuracy is given concerning the contents of the informaon contained in this publicaon. To the extent permied by law no liability (including liability to any person by reason of

negligence) will be accepted by TechNexion Ltd., its subsidiaries or employees for any direct or indirect loss or damage caused by omissions from or inaccuracies in this document.

• TechNexion Ltd. reserves the right to change details in this publicaon without noce. Please download the most updated version at: hps://www.technexion.com/support/download-center/

TC-1010-APL TC-1560-APL

Phone: +886-2-82273585 Web: www.technexion.com

16F-5, No. 736, Zhongzheng Road, ZhongHe District, 23511, New Taipei City, Taiwan

2020-01-06

6.2 Serial Ports (RS-XXX1/RS-XXX2)

4 External Connectors

5 LED Light Indicators

6.1 Digital I/O Connector (GPIO)

6 Pin Deﬁnion

This product is available with one GPIO connector. The non-galvanic isolated GPIO connector has the following pinout:

The TC-1010-APL / TC-1560-APL has two LED Light indicators. The Power LED Light indicator is lit, when the system is powered on. The SATA LED Light indicator is

blinking, when the SATA SSD is acve.

This product is available with two full funcon non-galvanic isolated RS-232 serial ports:

RS-XXX1 and RS-XXX2. The ports have the following pinout:

Description No.No. Description

Power LED indicator

Power Input connector

RS-XXX1 (Serial Port) DB9 connector

LAN1 RJ45 connector

LAN2 RJ45 connector

USB Host connector

miniDP1 connector

miniDP2 connector

SATA LED indicator

Grounding screw M4

Antenna hole

Power button

USB OTG (Type-C) connector

microSD cardslot

RS-XXX2 (Serial Port) DB9 connector

Micro-SIM cardslot

3.5mm audio jack

GPIO DB15 connector

RS-XXX1:

LED# Color

OFF

1 Power on

SATA SSD is active (blinking)

Green

Red

Power off

SATA SSD is not active

INDICATOR:

Front view:

Le view:

31 2 4 579

10 11

16 17 18

Rear view:

Right view:

23 25 26

12 13 14 15

20 21 22

Header on TC-1010-APL / TC-1560-APL: DB9 (9-pin) standard D-Sub male connector.

Cable receptacle: DB9 (9-pin) standard D-Sub female connector.

Header on TC-1010-APL / TC-1560-APL: DB9 (9-pin) standard D-Sub male connector.

Cable receptacle: DB9 (9-pin) standard D-Sub female connector.

Port Pin #

Signal

SERIAL1_DCD

SERIAL1_RXD

SERIAL1_TXD

SERIAL1_DTR

GND

SERIAL1_DSR

SERIAL1_RTS

SERIAL1_CTS

VCC

Description Device

Port#1 Data Carrier Detect (input)

Port#1 Receive data (input)

Port#1 Transmit data (output)

Port#1 Data Terminal Ready (output)

Ground

Port#1 Data Set Ready (input)

Port#1 Request-to-send (output)

Port#1 Clear-to-send (input)

5V supply output

COM1

The unit is by default preloaded with soware that can download and install a selecon of Linux OS images over hardwired network. Simply connect a display to the

unit though the miniDP connector and a network through the Ethernet LAN RJ45 connector and power it up, then follow the steps on the screen to load the

soware.Local proxies will interfere with this process. For more informaon, go to our Knowledge Base at: hps://www.technexion.com/support/knowledge-base/

To download drivers for the Windows operang systems, go to our Download Center at:

hps://www.technexion.com/support/download-center/

For more informaon about installing and conﬁguring the Windows operang systems, see: hps://msdn.microso.com/en-us/

7 Soware and Driver Installaon

3 4

Header on TC-1010-APL / TC-1560-APL: DB15 (15-pin) high density D-Sub male connector.

Cable receptacle: DB15 (15-pin) high density D-Sub female connector.

GPIO:

Port Pin #

Signal

VCC

GPIO1A