TeeJet Technologies AEROS 9040 User manual
Software version 4.31
USER MANUAL
AEROS 9040
Copyrights
© 2017 TeeJet Technologies. All rights reserved. No part of this document or the computer programs described in it may be reproduced, copied,
photocopied, translated, or reduced in any form or by any means, electronic or machine readable, recording or otherwise, without prior written
consent from TeeJet Technologies.
Trademarks
Unless otherwise noted, all other brand or product names are trademarks or registered trademarks of their respective companies or organizations.
Limitation of liability
TEEJET TECHNOLOGIES PROVIDES THIS MATERIAL “AS IS” WITHOUT WARRANTY OF ANY KIND, EITHER EXPRESSED OR IMPLIED.
NO COPYRIGHT LIABILITY OR PATENT IS ASSUMED. IN NO EVENT SHALL TEEJET TECHNOLOGIES BE LIABLE FOR ANY LOSS OF
BUSINESS, LOSS OF PROFIT, LOSS OF USE OR DATA, INTERRUPTION OF BUSINESS, OR FOR INDIRECT, SPECIAL, INCIDENTAL, OR
CONSEQUENTIAL DAMAGES OF ANY KIND, EVEN IF TEEJET TECHNOLOGIES HAS BEEN ADVISED OF SUCH DAMAGES ARISING FROM
TEEJET TECHNOLOGIES SOFTWARE.
Safety information
TeeJet Technologies is not responsible for damage or physical harm caused by failure to adhere to the following safety requirements.
As the operator of the vehicle, you are responsible for its safe operation.
The Aeros 9040 in combination with any assisted/auto steering device is not designed to replace the vehicle’s operator.
Do not leave a vehicle while the Aeros 9040 is engaged.
Be sure that the area around the vehicle is clear of people and obstacles before and during engagement.
The Aeros 9040 is designed to support and improve efciency while working in the eld. The driver has full responsibility for the quality and work
related results.
Disengage or remove any assisted/auto steering device before operating on public roads.
i
98-05304-EN R2
Aeros 9040 eld computer
HOMESETUPGUIDANCE FULL SCREENIMPLEMENT INTRODUCTIONGNSSRATE CONTROLAPPENDIX
Table of contents
CHAPTER 1 INTRODUCTION 1
Product upgrades available........................................................................................................................................................................1
SYSTEM COMPONENTS 1
Aeros 9040 console........................................................................................................................................................................................1
Buttons .....................................................................................................................................................................2
RealView® camera...........................................................................................................................................................................................2
Additional information.................................................................................................................................................................................2
BASIC SCREEN USE 3
Bottom tab keys ........................................................................................................................................................3
Unavailable options when job is active ......................................................................................................................3
Console screen colours.............................................................................................................................................4
Simple or advanced mode.........................................................................................................................................4
Warnings and information pop-ups ............................................................................................................................5
Setup option information ...........................................................................................................................................5
Drop-down menu selections ......................................................................................................................................5
Scrolling screens.......................................................................................................................................................5
Keyboard entry screen ..............................................................................................................................................6
Next page .................................................................................................................................................................6
Checkboxes ..............................................................................................................................................................6
CHAPTER 2 JOBS / HOME SCREEN 7
Simple mode .............................................................................................................................................................7
Advanced mode ........................................................................................................................................................7
SIMPLE MODE 8
New job..............................................................................................................................................................................................................8
Continue job.....................................................................................................................................................................................................8
Close job ............................................................................................................................................................................................................8
ADVANCED MODE 8
New job..............................................................................................................................................................................................................8
Start job..............................................................................................................................................................................................................8
Close job ............................................................................................................................................................................................................8
CHAPTER 3 FULL SCREEN VIDEO VIEW 9
Camera snapshot......................................................................................................................................................................................... 10
VSM camera options................................................................................................................................................................................... 10
CHAPTER 4 SYSTEM SETUP 11
Overview......................................................................................................................................................................................................... 11
ii www.teejet.com
Aeros 9040 eld computer
HOME SETUP GUIDANCEFULL SCREEN IMPLEMENTINTRODUCTION GNSS RATE CONTROL APPENDIX
CONFIGURATION 12
Implement...................................................................................................................................................................................................... 13
Single section setup ...............................................................................................................................................13
Section(s) with ISOBUS sprayer/spreader setup......................................................................................................14
Multiple sections with SDM/SFM setup....................................................................................................................15
Droplet size monitor ................................................................................................................................................16
Nozzle selection......................................................................................................................................................16
Reverse sense options............................................................................................................................................17
Mapping and guidance............................................................................................................................................................................. 17
Mapping and guidance [console only]......................................................................................................................17
Mapping and guidance using an external lightbar ....................................................................................................18
User entered mapping location................................................................................................................................19
GNSS................................................................................................................................................................................................................. 20
Video ................................................................................................................................................................................................................ 21
Sensors ............................................................................................................................................................................................................ 21
Input/output module pressure sensor.......................................................................................................................22
Nozzle ow monitor ................................................................................................................................................................................... 23
ISOBUS............................................................................................................................................................................................................. 23
Product............................................................................................................................................................................................................ 24
AutoSteer........................................................................................................................................................................................................ 25
FieldPilot [using a SCM]..........................................................................................................................................25
FieldPilot Pro / UniPilot Pro [using a SCM Pro]........................................................................................................25
Tilt correction................................................................................................................................................................................................ 27
DATA MANAGEMENT 28
Job data........................................................................................................................................................................................................... 28
Transfer ..................................................................................................................................................................29
Manage...................................................................................................................................................................29
Reports ............................................................................................................................................................................................................ 31
Options (Job mode).................................................................................................................................................................................... 32
Machine settings.......................................................................................................................................................................................... 33
Transfer ..................................................................................................................................................................33
Manage...................................................................................................................................................................34
CONSOLE 35
About ............................................................................................................................................................................................................... 35
Display............................................................................................................................................................................................................. 36
Cultural............................................................................................................................................................................................................ 36
Audio volume................................................................................................................................................................................................ 37
Demo GNSS ................................................................................................................................................................................................... 37
Restart Demo GNSS ...............................................................................................................................................38
Feature unlock.............................................................................................................................................................................................. 38
TOOLS 39
Upload software........................................................................................................................................................................................... 39
Extras................................................................................................................................................................................................................ 40
iii
98-05304-EN R2
Aeros 9040 eld computer
HOMESETUPGUIDANCE FULL SCREENIMPLEMENT INTRODUCTIONGNSSRATE CONTROLAPPENDIX
CHAPTER 5 GNSS RECEIVER CONFIGURATION 41
GNSS................................................................................................................................................................................................................. 41
GNSS type..............................................................................................................................................................42
GNSS port...............................................................................................................................................................42
Programme .............................................................................................................................................................44
PRN .......................................................................................................................................................................44
Show refresh GNSS position button ........................................................................................................................45
GNSS glossary ............................................................................................................................................................................................... 45
CHAPTER 6 IMPLEMENT SETUP 47
Multiple section output modules.......................................................................................................................................................... 47
IMPLEMENT TYPE 48
Section numbers .....................................................................................................................................................48
Straight............................................................................................................................................................................................................ 48
Single section .........................................................................................................................................................48
Multiple sections with SDM or SFM .........................................................................................................................49
Multiple sections with ISOBUS sprayer setup ..........................................................................................................50
Spreader – TeeJet......................................................................................................................................................................................... 51
Single section .........................................................................................................................................................51
Multiple sections .....................................................................................................................................................52
Spreader – OEM............................................................................................................................................................................................ 54
Single section .........................................................................................................................................................54
Multiple sections .....................................................................................................................................................54
Staggered....................................................................................................................................................................................................... 55
Multiple sections .....................................................................................................................................................55
APPLICATION OR WORKING WIDTH 57
Single section .........................................................................................................................................................57
Multiple sections .....................................................................................................................................................57
ISOBUS SPRAYER OFFSETS 58
Self-propelled – front mount ....................................................................................................................................58
Self-propelled – rear mount.....................................................................................................................................59
Three point hitch – front mount................................................................................................................................59
Three point hitch – rear mount ................................................................................................................................60
Trailed – always rear mount ....................................................................................................................................61
IMPLEMENT LATERAL OFFSET DISTANCE ADJUSTMENT 62
GNSS offset adjustment calculation.........................................................................................................................62
Implement lateral offset adjustment.........................................................................................................................63
REVERSE SENSE 64
Reverse on guidance screens .................................................................................................................................64
NOZZLE SELECTION 65
Preset .....................................................................................................................................................................65
Current nozzle.........................................................................................................................................................66
iv www.teejet.com
Aeros 9040 eld computer
HOME SETUP GUIDANCEFULL SCREEN IMPLEMENTINTRODUCTION GNSS RATE CONTROL APPENDIX
DROPLET SIZE MONITOR 66
Setup................................................................................................................................................................................................................ 66
Enable/disable DSM................................................................................................................................................66
Nozzle selection / current nozzle.............................................................................................................................66
Input/output module pressure sensor.......................................................................................................................66
Operation ....................................................................................................................................................................................................... 67
Status bar ...............................................................................................................................................................67
Guidance bar ..........................................................................................................................................................67
BOOMPILOT SECTION CONTROL 68
CHAPTER 7 GUIDANCE AND MAPPING 69
Overview......................................................................................................................................................................................................... 69
Screens options............................................................................................................................................................................................ 70
GUIDANCE BAR 74
Navigation activity & Boom status ...........................................................................................................................74
Selectable Information.............................................................................................................................................74
STATUS BAR 75
Status/information screens...................................................................................................................................................................... 76
NAVIGATION SCREENS 78
Vehicleview................................................................................................................................................................................................... 78
Fieldview........................................................................................................................................................................................................ 79
RealView guidance...................................................................................................................................................................................... 80
GUIDANCE MODES 81
Straight AB guidance.................................................................................................................................................................................. 81
Curved AB guidance................................................................................................................................................................................... 81
Adaptive curve AB guidance................................................................................................................................................................... 81
Circle pivot guidance ................................................................................................................................................................................. 81
Last pass guidance...................................................................................................................................................................................... 81
NextRow guidance...................................................................................................................................................................................... 82
No guidance .................................................................................................................................................................................................. 82
GUIDELINES 82
Marking A and B points............................................................................................................................................................................. 82
A+ nudge feature ....................................................................................................................................................83
Next guideline feature............................................................................................................................................................................... 84
Last pass guidelines.................................................................................................................................................................................... 84
NextRow guidelines.................................................................................................................................................................................... 85
Azimuth degree ........................................................................................................................................................................................... 85
RETURN TO POINT 86
Marking a return point .............................................................................................................................................86
Delete the return point.............................................................................................................................................86
Guidance to a return point.......................................................................................................................................86
v
98-05304-EN R2
Aeros 9040 eld computer
HOMESETUPGUIDANCE FULL SCREENIMPLEMENT INTRODUCTIONGNSSRATE CONTROLAPPENDIX
BOOMPILOT 87
No Section control module...................................................................................................................................................................... 87
ISOBUS sprayer............................................................................................................................................................................................. 88
ISOBUS spreader.......................................................................................................................................................................................... 89
With TeeJet section control module and switchbox or ISM......................................................................................................... 90
With TeeJet section control module..................................................................................................................................................... 90
CURVED LOOKAHEAD 90
REFRESH GNSS POSITION 91
NOZZLE FAULT RESET 91
BOUNDARIES AND POLYGONS 92
Boundaries..................................................................................................................................................................................................... 92
Establishing an exterior or interior boundary ...........................................................................................................92
Delete last marked boundary...................................................................................................................................94
Boundary on status bar ...........................................................................................................................................94
Polygons ......................................................................................................................................................................................................... 94
Establishing a polygon ...........................................................................................................................................94
Delete last marked polygon .....................................................................................................................................95
MAPPING OPTIONS 96
Polygon mapping........................................................................................................................................................................................ 96
Rate control mapping................................................................................................................................................................................ 96
APPLICATION CONTROL OPTIONS 97
ZOOM IN/OUT 97
Vehicleview................................................................................................................................................................................................... 97
Fieldview........................................................................................................................................................................................................ 97
PAN MODE 98
REALVIEW SPECIFIC OPTIONS 98
RealView guidance options ..................................................................................................................................................................... 99
Camera snapshot......................................................................................................................................................................................... 99
VSM camera options................................................................................................................................................................................... 99
CHAPTER 8 RATE CONTROL 101
Ready for operation..................................................................................................................................................................................102
ISOBUS configuration options ...............................................................................................................................102
NAVIGATION SCREEN OPTIONS 103
Guidance bar ........................................................................................................................................................103
Current pressure ...................................................................................................................................................103
vi www.teejet.com
Aeros 9040 eld computer
HOME SETUP GUIDANCEFULL SCREEN IMPLEMENTINTRODUCTION GNSS RATE CONTROL APPENDIX
Application control options ....................................................................................................................................103
Mapping options....................................................................................................................................................104
MAPPING OPTIONS 104
Coverage map.............................................................................................................................................................................................105
Polygons map .............................................................................................................................................................................................105
Prescription map........................................................................................................................................................................................106
Application and target rate maps.......................................................................................................................................................106
Application map ...................................................................................................................................................106
Target rate map.....................................................................................................................................................107
Colour range selection ..........................................................................................................................................107
APPENDIX A SYSTEM CONFIGURATIONS 109
APPENDIX B AEROS CONSOLE MENU SETTINGS 112
APPENDIX C UNIT SPECIFICATIONS 116
APPENDIX D SETTING RANGES 116
APPENDIX E UTM COORDINATES AND ZONES 117
1
98-05304-EN R2
Aeros 9040 eld computer
HOMESETUPGUIDANCE FULL SCREENIMPLEMENT GNSSRATE CONTROLAPPENDIX INTRODUCTION
CHAPTER 1 INTRODUCTION
The Aeros 9040 eld computer allows the management of multiple connected modules plus GNSS mapping, guidance, FieldPilot®,
BoomPilot®, ISOBUS Rate Control, Nozzle Flow Monitor, and data collection in a single console using CAN bus technology. This replaces
multiple consoles in the cab with one robust system.
Product upgrades available
• FieldPilot®Pro auto steering
• UniPilot®Pro assisted steering
• BoomPilot®automated boom section control
• Tilt gyro module
• Video selection modules for up to 8 cameras
• External GNSS receiver or antenna upgrades
• Fieldware®Link enhanced data organization application
• Pressure sensor interface kit for droplet size monitor
• ISOBUS rate control
• Reverse sense module
• Nozzle ow monitoring
SYSTEM COMPONENTS
Aeros 9040 console
The Aeros 9040 is designed to provide years of service under typical agricultural operating conditions. A tight tting enclosure, combined
with rubber covers for all connectors mean that typical dusty environments will not cause operational problems. While occasional splashing
of water will not damage the unit, the Aeros 9040 is not designed for direct exposure to rain. Take care not to operate the Aeros 9040 in wet
conditions.
Figure 1-1: Aeros 9040 console front
USB ports with rubber covers
Bright touch screen
Power button
Favorites button
Home button
2www.teejet.com
Aeros 9040 eld computer
HOME SETUP GUIDANCEFULL SCREEN IMPLEMENTGNSS RATE CONTROL APPENDIXINTRODUCTION
Figure 1-2: Aeros 9040 console back
Integrated RAM mount
(assembly required) Speed digital (LAN) connection
with rubber cover
Camera connection
with rubber cover
Power connection
Speakers
GNSS antenna connection
WiFi antenna connection USB ports with rubber covers
Buttons
Home
The Home button provides a shortcut to the Home screen.
Favorites
The Favorites button provides a shortcut to a frequently used console bottom tab. To assign a tab to the button, navigate to that tab’s
screen, then press and hold the Favorites button until it beeps.
Power on/off
On – Press the POWER button to power on the console. Upon power up, the Aeros will begin its start up sequence.
Off – Press and briey hold the POWER button until a conrmation screen acknowledges shut down mode.
WARNING! Wait 10 seconds before restarting the console.
RealView® camera
The TeeJet Technologies RealView camera allows video images to be displayed on the Aeros screen. The camera can be pointed forward to
enable RealView guidance over video, or it can be positioned to view other operational aspects of your equipment. The camera is equipped
with a exible RAM mount, integral sun shade and provides infrared illumination, allowing clear video images even in dark conditions.
Additional information
All changes are saved automatically.
The console needs to be cycled off and back on when changing or attaching equipment to the Aeros system.
Start up sequence
The console takes approximately two-three minutes to power up. During this time a series of screens will be displayed, LEDs will power on
and off, and brightness levels will uctuate. Once the power up sequence has completed, the Home screen will appear.
Recommended antenna installation
The GNSS antenna should be mounted as far forward as possible on top of the cab on a metal surface of at least 10 cm × 10 cm.
USB ports
Only one USB port can be used at any given time.
3
98-05304-EN R2
Aeros 9040 eld computer
HOMESETUPGUIDANCE FULL SCREENIMPLEMENT GNSSRATE CONTROLAPPENDIX INTRODUCTION
BASIC SCREEN USE
The Aeros 9040 can be used as a simple current job system or advanced multi-job system. Regardless of which mode the console is in, the
basic screen functions are the same.
• Bottom tabs and side tabs access the various screens and sub-screens
• Warnings and information pop-ups inform user of console activities and details on setup or guidance functions
• Setup options can easily be set using the drop-down menus or keyboard entry screens
To quickly nd a setup feature, see “Aeros console menu settings” in this manual.
Bottom tab keys
The bottom tab keys are always available on screen. These keys
give access to jobs, setup options, and navigation.
Home/job screen
System setup
Vehicle view guidance
Field view guidance
RealView guidance or
RealView camera full screen video view
NOTE: RealView Guidance options are only available with a
camera installed on the system.
ISOBUS universal terminal
Figure 1-3: Bottom tab keys
0.0
km/h
0.00
ha 0.0
3.5
(bar)
Unavailable options when job is active
When a job is active some setup options are unavailable: see “Aeros
console menu settings” in this manual.
Figure 1-4: Examples of unavailable options
4www.teejet.com
Aeros 9040 eld computer
HOME SETUP GUIDANCEFULL SCREEN IMPLEMENTGNSS RATE CONTROL APPENDIXINTRODUCTION
Console screen colours
The console is available in six colour schemes. From the System
setup bottom key, press CONSOLE side tab and enter
the Display options. Press DOWN arrow to access the Colour
scheme options to select colour mode.
Figure 1-5: Colour schemes
Simple or advanced mode
To change between simple mode and advanced mode, see the
conguration chapter under Data –> Options.
In simple mode, only one job will be available at a time. Only
bounded area and coverage areas are displayed on the home
screen. Only the current job is available for saving in Reports. Use
with Fieldware Link is not available.
Figure 1-6: Simple mode home screen
In advanced mode, more than one job will be available at any time.
Client, farm, eld and job names; bounded and coverage areas;
application time; and distance from selected job are displayed on the
home screen. All saved job proles can be exported as a PDF, SHP
or KML le to a USB drive using Data -> Reports.
Client information, farm information, eld information, and
prescription maps can only be inputted using Fieldware Link. A job
name can only be edited using Fieldware Link.
A user can duplicate jobs for reuse of guidelines, boundaries, applied
data, prescription map and/or polygons using Fieldware Link or
Data -> Job data -> Manage in the console.
Figure 1-7: Advanced mode home screen
5
98-05304-EN R2
Aeros 9040 eld computer
HOMESETUPGUIDANCE FULL SCREENIMPLEMENT GNSSRATE CONTROLAPPENDIX INTRODUCTION
Warnings and information pop-ups
A pop-up warning or information box will be displayed for
approximately ve (5) seconds. To remove the information box, tap
anywhere on the screen.
Figure 1-8: Example of information text box
Setup option information
Press the option’s icon or option’s name of any menu item to display
a denition and range values of that item. To remove the information
box, press anywhere on the screen.
Figure 1-9: Example of information text box
Drop-down menu selections
Press DOWN arrow to access the options. Use the UP/DOWN
arrows or slide bar if necessary to scroll through the extended
list. Select the appropriate option. To close the list without selecting an
option, tap anywhere on the screen outside the drop-down menu.
Figure 1-10: Example of drop-down menu
Backward
Forward
Scrolling screens
Some screens have more information or options that are visible
beyond the current screen. Use the UP/DOWN arrows or
slide bar to access additional options or information not currently
visible on the screen.
Figure 1-11: Example of scrolling screen
6www.teejet.com
Aeros 9040 eld computer
HOME SETUP GUIDANCEFULL SCREEN IMPLEMENTGNSS RATE CONTROL APPENDIXINTRODUCTION
Keyboard entry screen
Press the KEYPAD icon . Use the numeric keypad to enter
a value.
Press the ACCEPT icon to save the settings or the
CANCEL icon to leave the keypad without saving.
Figure 1-12: Example of keyboard
GNSS antenna height (m)
1 2 3
3.50
Clear
4 5 6 <--
7 8 9
0 . +/-
Next page
Press the NEXT PAGE arrow to set up additional options for the
selected item.
Figure 1-13: Example of next page
Checkboxes
Press the CHECKBOX / to select or deselect.
Figure 1-14: Example of checkboxes
7
98-05304-EN R2
Aeros 9040 eld computer
SETUPGUIDANCE FULL SCREENIMPLEMENT INTRODUCTIONGNSSRATE CONTROLAPPENDIX HOME
CHAPTER 2 JOBS / HOME SCREEN
Once the power up sequence has completed and the console is receiving GNSS, the Home screen will appear with the option to start a new
job or continue an existing job.
Setup for the specic machine and its components must be completed before starting a job. Once a job is
active, some setup options can no longer be changed. See “Aeros console menu settings” in the appendix of this manual.
To change between simple and advanced mode, go to Data-> Options-> Job mode in the System setup.
Simple mode
In simple mode, only one job will be available at a time. Only
bounded area, coverage areas, and application time are displayed
on the home screen. Only the current job is available for saving in
Reports. Use with Fieldware Link is not available.
Figure 2-1: Simple mode home screen
Advanced mode
In advanced mode, more than one job will be available at any time.
Client, farm, eld and job names; bounded and coverage areas;
application time; and distance from selected job are displayed on the
home screen. All saved job proles can be exported as a PDF, SHP
or KML le to a USB drive using Data -> Reports.
Client information, farm information, eld information, and
prescription maps can only be inputted using Fieldware Link. A job
name can only be edited using Fieldware Link.
A user can duplicate jobs for reuse of guidelines, boundaries, applied
data, prescription map and/or polygons using Fieldware Link or
Data -> Job data -> Manage in the console.
Figure 2-2: Advanced mode home screen
8www.teejet.com
Aeros 9040 eld computer
SETUP GUIDANCEFULL SCREEN IMPLEMENTINTRODUCTION GNSS RATE CONTROL APPENDIXHOME
SIMPLE MODE
Once the power up sequence has completed, the Home screen will
appear with the option to start a new job or continue an existing job.
The console must have GNSS before starting or continuing a job.
New job
Starting a new job will clear the previous job data.
To start a new job:
1. On the Home screen , press New job .
The console will jump to Vehicle View.
Continue job
To continue the existing job:
1. On the Home screen , press Continue .
The console will jump to Vehicle view and begin providing navigation
information.
Distance
If a selected job is in a UTM zone other than the current or adjacent
UTM zone, “Out of range” will be displayed next to Distance, and
Continue will be disabled.
NOTE: For more information, see the UTM zone appendix.
If a selected job has no recorded information, Distance will show “No
data”.
Close job
To close a job:
1. On the Home screen , press Close job .
To create a report of the job when closing a job:
1. Insert a USB drive into the USB port of the console.
2. On the Home screen , press Close job .
3. Select:
►Yes – to create a report of the last job
►No – to return to the Home screen without saving
ADVANCED MODE
Once the power up sequence has completed, the Home screen will
appear with the option to start a new job or continue an existing job.
The console must have GNSS before starting or continuing a job.
New job
Starting a new job will clear the previous job data.
To start a new job:
1. On the Home screen , press New job .
2. Press:
►Yes – to automatically generate a name
►No – to enter a name using the on screen keyboard
Client, farm, and eld information are inputted using Fieldware Link.
The console will jump to Vehicle view.
Start job
The Aeros 9040 is programmed with a eld nder tool to assist the
user in nding the job closest to the vehicle’s location. With GNSS
acquired, the job pick list will be updated every ten seconds. During
this update, the list of jobs is sorted by distance and the closest two
jobs are displayed on the top of the list. The remaining jobs are listed
beneath these.
To continue the existing job:
1. On the Home screen , press DOWN arrow to access the
list of jobs saved in the console.
2. Select the job name to be started/continued.
3. Press Start job .
The console will jump to Vehicle View and begin providing navigation
information.
Distance
If a selected job is in a UTM zone other than the current or adjacent
UTM zone, “Out of range” will be displayed next to Distance, and
Start job will be disabled.
NOTE: For more information, see the UTM zone appendix.
If a selected job has no recorded information, Distance will show “No
data”.
Close job
To close a job:
1. On the Home screen , press Close job .
To create a report of the job when closing a job:
1. Insert a USB drive into the USB port of the console.
2. On the Home screen , press Close job .
3. Select:
►Yes – to create a report of the last job
►No – to return to the Home screen without saving
9
98-05304-EN R2
Aeros 9040 eld computer
HOMESETUPGUIDANCE IMPLEMENT INTRODUCTIONGNSSRATE CONTROLAPPENDIX FULL SCREEN
CHAPTER 3 FULL SCREEN VIDEO VIEW
RealView full screen video view allows live video input to be displayed. View video feed(s) and setup cameras without GNSS available.
Options for RealView guidance are not available on this screen.
►Single camera – a single camera is directly attached to the console
►Video selection module – if a Video Selection Module (VSM) is installed on the system, two (2) video options are available:
• One camera view – one of up to eight camera inputs can be selected to change the view of the video input.
• Split camera view – one of two sets of four camera inputs (A/B/C/D or E/F/G/H) can be selected to divide the screen into four
separate video feeds.
To adjust the camera view [reverse, upside down], go to Setup-> Conguration-> Video.
To enter Full screen video mode:
1. Press REALVIEW CAMERA FULL SCREEN VIDEO VIEW bottom tab .
2. Press REALVIEW OPTIONS tab to display RealView options.
3. Select from:
►Single camera view [VSM only] – one (1) of up to eight (8) camera inputs can be selected to change the view of the video input
►Split camera view [VSM only] – one (1) of two (2) sets of four (4) camera inputs (A/B/C/D or E/F/G/H) can be selected to divide the
screen into four separate video feeds
►RealView camera image capture – saves a still photo of the current view on the screen to a USB drive
Figure 3-1: RealView full screen video view
10 www.teejet.com
Aeros 9040 eld computer
HOME SETUP GUIDANCEIMPLEMENTINTRODUCTION GNSS RATE CONTROL APPENDIXFULL SCREEN
Camera snapshot
RealView camera snapshot saves a still photo of the current
view on the screen to a USB drive.
1. Insert USB drive.
2. Press REALVIEW CAMERA FULL SCREEN VIDEO VIEW
bottom tab .
3. Press REALVIEW OPTIONS tab to display RealView
options.
4. Press CAMERA SNAPSHOT icon .
Figure 3-2: RealView camera full screen video view
VSM camera options
If a Video selection module (VSM) is installed on the
system, two (2) video options are available:
1. Press REALVIEW CAMERA FULL SCREEN VIDEO VIEW
bottom tab .
2. Press REALVIEW OPTIONS tab to display RealView
options.
3. Select from:
►Single camera view – one (1) of up to eight (8) camera
inputs can be selected to change the view of the video input.
►Split camera view – one (1) of two (2) sets of four (4)
camera inputs (A/B/C/D or E/F/G/H) can be selected to divide
the screen into four separate video feeds.
Figure 3-3: Single camera selection with VSM
Figure 3-4: Select split view with VSM
11
98-05304-EN R2
Aeros 9040 eld computer
HOMEGUIDANCE FULL SCREENIMPLEMENT INTRODUCTIONGNSSRATE CONTROLAPPENDIX SETUP
CHAPTER 4 SYSTEM SETUP
System Setup is used to congure the console, the machine and its implements. Four side tabs access options for Machine/Implement
Conguration, Data management, Console settings, and Tools.
Overview
Four side tabs access setup options for:
Conguration
• Implement (straight, spreader, or staggered implement
congurations; nozzle selection information including droplet
size monitor, reverse conguration)
• Mapping and Guidance (mapping location, guidance sensitivity,
external lightbar)
• GNSS receiver conguration
• Video conguration
• Sensors (Input/output module (IOM) pressure sensor)
• Nozzle ow monitor
• ISOBUS conguration
• Product conguration
• AutoSteer
◄FieldPilot (valve setup, steering settings, valve test, valve
diagnostics, steering wheel sensor, steering angle sensor)
◄FieldPilot Pro / UniPilot Pro (manage vehicle, calibrations,
adjustments, select qi values, transport mode, service mode)
• Tilt correction
Data management
• Job data (transfer, manage)
• Reports
• Options (job mode)
• Machine settings (transfer, manage)
Console settings
• About (system information)
• Display
• Cultural
• Audio volume
• Demo GNSS
• Feature unlock
Tools
• Upload software
• Extras (calculator, units converter)
Figure 4-1: Setup options
Conguration side tab
Data management side tab
Console settings side tab
Tools side tab
System setup bottom tab
Side tabs
12 www.teejet.com
Aeros 9040 eld computer
HOME GUIDANCEFULL SCREEN IMPLEMENTINTRODUCTION GNSS RATE CONTROL APPENDIXSETUP
CONFIGURATION
Conguration is used to congure the system components including
implements, guides, steering, monitors and sensors.
NOTE: Feature availability will vary depending on the devices
available and unlocked on the Aeros 9040 system.
1. Press SYSTEM SETUP bottom tab .
2. Press CONFIGURATION side tab .
3. Select from:
►Implement – used to set (as appropriate) machine type,
GNSS antenna height, implement type, symmetric implement
layout, section output modules, number of implement
sections, application/working width, droplet size monitor,
nozzle selection, nozzle spacing, BoomPilot start mode,
reverse sense module
● In Straight mode – in-line/lateral implement offset direction/
distance, overlap percentage, implement delay on/off time
● In Spreader mode:
TeeJet – antenna to disks distance, lateral implement offset
direction/distance, overlap percentage, delay on/off times,
spread offset distance, section offset distances, section
lengths
OEM – antenna to disks distance, lateral implement offset
direction/distance, start/stop distance, section start/stop
offset distances
● In Staggered mode – in-line/lateral section 1 offset
direction/distance, overlap percentage, delay on/off times,
section offsets
►Mapping and guidance – used to congure the mapping
location, guidance width, guidance sensitivity (cross track
error) and/or an optional external lightbar module (ELM)
►GNSS – used to establish GNSS type, port, and PRN, as well
as to view GNSS status information
►Video – used to set up individual cameras
►Sensors – used to establish pressure sensor settings
►Nozzle ow monitor – used to establish nozzle conguration,
and to establish and calibrate ow limits and alarm behavior
for nozzle ow monitors
►ISOBUS – used to select information for broadcast over the
ISOBUS, and in troubleshooting
►Product – used to congure product name, tank/bin volumes,
target application rates, increment for adjusting target rates,
and colour mapping maximum/minimum rate limits and
corresponding display colours
►AutoSteer – used to enable/disable and calibrate assisted/
auto steering
● FieldPilot – used to establish valve setup settings, steering
settings, steering wheel and steering angle sensor settings,
and to perform valve tests or valve diagnostics
● FieldPilot Pro / UniPilot Pro – used to manage vehicle
settings, calibrate sensors, select QI values, as well as
establish transport mode and service mode
►Tilt correction – used to enable/disable and calibrate the tilt
correction function, and improve application on hilly or sloped
terrain
Figure 4-2: Configuration options
Other manuals for AEROS 9040
1
Table of contents
Other TeeJet Technologies Monitor manuals
