TEi Lighting BRAINSPOT250II User manual

1
-
1.
Safety Instruction
2.
Technical Specific
ation
3.
Lamp
4.
How To Set The Unit
4.1 Control Panel
4.2
Main Function
4.3 Home Position Adjustment
5.
How To Control The Unit
5.1 Master/Slave Built
-
In Preprogrammed Function
5.2
Easy Controller
5.3
DMX Controller
5.4
DMX
512 Configuration
5.5
DMX
512 Connection
6.
Troubl
eshooting
7.
Maintenance and
Cleaning
85
-
05275
B
RA
IN
SPOT
250II
User Guide
TABLE OF CONTENTS
Please read these instructions carefully before use

2
-
Please keep this User Guide for future consultation. If you sell the unit to another user,
be sure that they also receive this instruction booklet
.
Unpack and check carefully
there is no transportation damage before using the unit.
Before operating, ensure that the voltage and frequency of power supply match the
power requirements of the unit.
It’s important to ground the yellow/green conductor to earth in order to avoid electr
ic
shock.
The unit is for indoor use only. Use only in a dry location.
The unit must be installed in a location with adequate ventilation, at least 50cm from
adjacent surfaces. Be sure that no ventilation slots are blocked.
Disconnect main power before fus
e/lamp replacement or servicing.
Replace fuse/lamp only with the same type.
Make sure there are no flammable materials close to the unit while operating, as it is
fire hazard.
Use safety chain when fixes this unit. Don’t handle the unit by taking its head
only, but
always by taking its base.
Maximum ambient temperature is T
a
: 40
. Don’t operate it where the temperature is
higher than this.
Unit surface temperature may reach up to 85
. Don’t touch the housing bare
-
hand
during its operation, and allow about
15 minutes to cool down before replacing bulb or
serving, as the unit could be very hot.
In the event of serious operating problem, stop using the unit immediately. Never try to
repair the unit by yourself. Repairs carried out by unskilled people can lead
to damage
or malfunction. Please contact the nearest authorized technical assistance center.
Always use the same type spare parts.
Don’t connect the device to any dimmer pack.
Do not touch any wire during operation, as there might be a hazard of electric s
hock.
3
-
To prevent or reduce the risk of electricalshock or fire, do not expose the unit to rain or
moisture.
Never touch bulb with bare fingers, as it is very hot after using.
Hot lamp explosion hazard. Do notopen the unit within five minutes a
fterswitching off.
Do not start on the unit without bulb enclosure or
when
housing is damaged.
The housing, the lenses, or the ultraviolet filter must be replaced if they are visibly
damaged.
Do not look directly at the light while the bulb is on.
There are no user serviceable parts inside the unit. Do not open the housing or attempt any
repairs
by
yourself. In the unlikely event your unit may require service, please contact your
nearest dealer.
The unit should be mounted via its scr
ew holes on the
bracket
(please refer to the drawing
below)
.
Always ensure that the unit is firmly fixed to avoid vibration and slipping while
operating. Always ensure that the structure to which you are attaching the unit is secure
and is able to support
a weight of
10 times of the unit
’
s weight. Also always use a safety
cable that can hold 12 times of the weight of the unit when installing the fixture.
The equipment must be fixed by professionals.
And it mustbe fixed at
a
place where is out of
the touch
of
people
and has no one pass by or
under it
.
1
.
Safety Instruction
WARNING
Please read carefully the instruction, which includes important
information about the installation, usage and maintenance.
Warning
Cautio
n
Installation
l
l
l
l
l
l
l
l
l
l
l
l
l
l
l
l
l
l
l
l
l
?
?

4
-
-
AC 120V~60Hz
or
AC 230
/240/250
V~50
/60
Hz
-
MSD 250W/ NSD 250/2 W
-
LED: Total 12pcs, Red: 4pcs, Green: 4pcs, Blue: 4pcs
-
High efficienc
y optical system
-
High quality optical lens and dichroic colors
-
Beam angle: 13
-
Blackout,
0~100 smooth
dimm
ing
and strobe speed
variable(1~1
0
flashes per
second).
-
Independent color wheel with 9
trapezoid
dichroic
color
s plus w
hite.
-
Color wheel rotates with variable speed, giving rainbow effect
.
-
Independent
gobo
wheel with 7
rotating, interchangeable
gobos plus open
: 5 metal
gobos, 2 glass gobos are included.
-
Gobo wheel rotates with variable speed
, giving shaking
effe
ct
.
-
Prism/Rotating Prism
-
Pan: 540° in 2.8 second.
-
Tilt:270° in 1.6 second.
Channel 1 =
Pan
Ch
annel 1
2 = Prism Rotation
Channel 2 =
Tilt
Ch
annel 1
3 = Focus
Channel
3
=
Pan/Tilt Speed selection
Ch
annel 1
4 = Pan 16
bit
Channel
4
=
Dimmer
Ch
annel 1
5 = Tilt 16 bit
Channel
5
=
Shutter/S
haking
Ch
annel 1
6 = Reset/Lamp on/off
Channel
6
=
Color
Channel 17 = Red LED
Channel 7 = No Function
Channel 18 = Green LED
Channel 8 = No Function
Channel 19 = Blue LED
Channel 9
= Gobo
Channel 20 = LED Color Macro
Ch
annel 10
= Gobo Rotation
Channel 21 = Dimmer/Strobe
Ch
annel 1
1 = Prism
5
-
428
x
369
x
466
mm
(L x W x H)
23
kg
Open the cover by loosening the fastening screw at the sides of the cover.
If you wish to use other forms and patterns as
the standard
-
gobos, orif the gobos are to be
exchanged, remove the fixation ring with an appropriate tool.Remove the gobo and insert
the new gobo. Press the fixation
-
ring together and insert it in the front of the gobo.
2
.
Technical Specification
Power supply
Light
Source
Optical system
Shutter
/Dimmer
Color wheel
Gobo
wheel
Effect Wheel
Movement
DMX Channels
Luminous intensity:
Dimension:
Weight:
2.1. Inserti
ng/Exchanging rotating gobos
°
DANGER!
Install the gobos with the device switched off only.
Unplug from mains before
changing gobos
!

6
-
Because of its high internal pressure, there might be a risk that the Discharge lamp
would explode during operation. The lamp emits intense UV radiation which is
harmful
to the eyes and skin. The high luminance of the arc
can cause severe damage to the
retina if look
s
directly at the lamp.
MSD 250W/ NSD 250/2 W
1.
Always switch off the main supply and never
handle the lamp or luminai
r
e when
it
is
hot.
2.
Do not touch
the bulb with bare hands. If this
happens, clean the lamp with denatured
alcohol and wipe it with a lint free cloth before
installation.
3.
The lamp generates UV radiation. Never
operate the lamp without appropriate shielding.
4.
When burning, the lamp operates
at high
pressure and there is a slight risk of arc tube
rupture. The risk increases with age,
temperature and improper handling of the lamp. Do not use the lamp any longer than its
specified life.
5.
Make sure the lamp is located in the center of the reflect
or for the best spot.
In case of replacement of the lamp or maintenance, do notopen the
fixture
within 15 minutes until the unit cools down after
switching
7
-
To show the various menu
s
and the selected functions
DMX
On
DMX input present
MASTER
On
M
aster mode
SLAVE
On
S
lave mode
SOUND
Flashing
S
ound activation
MENU
T
o select the programming functions
DOWN
T
o go backward in the selected functions
UP
T
o go forward in the selected functions
ENTER
T
o confirmthe selected functions
By connect
ing
to
CA
-
8
to control the unit
for Stand by,
Function,
and
Mode
function.
To adjust the
sound
-
input
sensitivity
For DMX512
operation
, use 3
-
pin XLR plug cable to link the unit together.
CAUTION!
Never unscrew the screw
s of the rotating gobo as the ball bearing
will otherwise be opened!
3.
Lamp
WARNING
4
.
How To Set The Unit
4.1
.
Control Panel
Display
LED
Button
Remote controller input
Sensitivity
DMX input/output

8
-
To select any of the
pre
-
set
functions, press the
button up to when the required one
is shown on the display. Select the function by
button and the display will blink. Use
and
button to change the mode. Once the required mode has been selected,
press the
button to setup or itwill
automatically return to the main functions without
any change after idling 8 seconds. To go back to the functions without any change press
the
button. The main functions are shown below:
Press the
button up to when th
e
is shown on the display. Pressing
button and the display will blink. Use
and
button to change the DMX512
address.
Once the address has been selected, press the
button to setup. Idling 8 seconds
automatically exit menu mode. Back to
the functions without any change press
button.
9
-
Press the
button up to when the
is showing on the display. Pressing
button and the display will blink. Use
and
button to select the
(show 1) or
(show 2)
or
(show 3
)
or
(show 4)
mode. Once the
mode has been selected, press the
button to setup.
Idling 8 seconds automatically
exit menu mode. Back to the functions without any change press
button.
Show 1 mode
-
Fixture is placed on the floor. Tilt moveme
nt angle 210°.
Show 2 mode
-
Fixture is fixed under ceiling. Tilt movement angle 90°.
Show 3 mode
-
Fixture is placed on the
speaker
,
The spot is always projecting
to the audience
’
s direction; i.e in front of the stage.
Pan movement angle
( left to
right to
left ):
160
°
.
Tilt movement angle
:
90°
(
6
0°
above horizon; 3
0°
below horizon)
.
Show 4 mode
-
Fixture is fixed
under ceiling.
The spot is mainly projecting in
front of the stage.
Pan movement angle
(left to right to left)
:
160
°
.
Tilt movemen
t angle
:
90° ( vertically, front 75°
; back 15
°
)
.
Press the
button up to when the
is shown on the display. Pressing
button and the display willblink. Use
and
button to select the
(normal)
or
(2 light show) mode. Onc
e the mode has been selected, press the
button to setup. Idling 8 seconds automatically exit menu mode. Back to the functions
without any change press
button.
Press the
button up to when the
is shown on the display. Press
ing
button and the display will blink. Use
and
button to select the
(
yes
blackout
) or
(
no blackout
) mode. Once the mode has been selected, press the
button to setup. Idling 8 seconds automatically exit menu mode. Back to the
functio
ns without any change press
button.
Press the
button up to when the
is shown on the display. Pressing
button and the display will blink. Use
and
button to select the
(normal)
4.2. Main Function
MENU
ENTER
DOWN
UP
ENTER
MENU
DMX512 Address Setting
MENU
ENTER
DOWN
UP
ENTER
MENU
Show Mode
MENU
ENTER
DOWN
UP
ENTER
MENU
Slave Mode
MENU
ENTER
DOWN
UP
ENTER
MENU
Blackout
Mode
MENU
ENTER
DOWN
UP
ENTER
MENU
Pan Inversion
MENU
ENTER
DOWN
UP