Tekky POP OUT TRASH RACCOON User manual

POP OUT TRASH RACCOON
INSTALLATION AND OPERATING INSTRUCTIONS
KEEP ALL PLASTIC AND WIREPARTS AWAY FROMCHILDREN.
WARNING: DO NOT TURN ON THE PROP UNTIL FULLY ASSEMBLED. STAY CLEAR OF THE PROP WHILE OPERATING.
ESTIMATED ASSEMBLY TIME SEVEN MINUTES.
PARTS
ASSEMBLY
1. METAL BASE AND
CONTROL BOX
2. FABRIC TRASH CAN
3. RACCOON
4. SAND BAG
5. 6V 2A ADAPTER
6. METAL STAKES
1. 2. 3. 4. 5. 6.
1. Roll back the fur fabric on the
RACCOON and push the spring
lock to secure the RACCOON to
the METAL BASE AND CONTROL
BOX. Release spring lock
to secure.
MATCH A TO A
2. Connect the wire bundle from
the MODULE to the wire bundle
from the RACCOON.
MATCH B TO B
5. Connect the wire bundle from
the CONTROL BOX to the wire
bundle running from the
motion sensor.
MATCH C TO C
3. Unfasten the two ties at the
base of the FABRIC TRASH
CAN and unfold from
collapsed position.
4. Insert the assembled
RACCOON and METAL BASE into
the FABRIC TRASH CAN.
Position the METAL BASE over
the three sets of hook and loop
fasteners.
7. Wrap and secure the rst hook
and loop fastener in the front of
the FABRIC TRASH CAN over the
front foot of the METAL BASE.
8. Wrap and secure the second
set of two hook and loop
fasteners in the middle of the
FABRIC TRASH CAN over the
middle arms of the METAL BASE.
6. Locate the front foot of the
METAL BASE.
Slide the SANDBAG over the front
foot of the METAL BASE and slide
it towards the RACCOON BODY.
™

Requires 6V 2A ADAPTER (included)
or 4AA batteries (not included)
ALL NEW MATERIALS:
METAL, FOAM, PLASTIC, POLYESTER
Surface washable only.
POP OUT TRASH RACCOON™
is a trademark of Tekky.
Copyright © 2022 Tekky.
All Rights Reserved.
MADE IN CHINA
visit us at tekkydesign.com
9. Reach through the back
FABRIC TRASH CAN ap and
secure the fourth hook and loop
fastener in back of the FABRIC
TRASH CAN to the METAL FRAME.
11. Roll the fur fabric back down
on the RACCOON and close the
ap in back of the BARREL.
Secure the three hook and
loop fasteners to complete
your setup.
10. Insert 4 AA batteries (not
included) or 6V 2A adapter
(included) into the control box.
Move the switch to the on
position. Make a loud sound
(clap) or move in front of the item
to activate. Turn the item o
when not in use. Remove
6V 2A adapter when
using batteries.
To further secure your FABRIC TRASH CAN
for sheltered outdoor use, rmly insert
METAL STAKES through the metal
grommets. The grommets are located
near the front and back of the BASE
inside the FABRIC TRASH CAN.
BACK GROMMET
FRONT GROMMET
EXTERNAL SPEAKER IS NOT INCLUDED. MUST BE PURCHASED SEPARATELY.
1. Plug speaker cord into the jack labeled SPEAKER JACK
located on the MODULE.
2. Use volume knob on external speaker to control volume levels.
OPTIONAL EXTERNAL SPEAKER SET UP
OPTIONAL METAL STAKE SET UP
1. Insert the cable from optional footpad into the jack labeled
FOOTPAD on the MODULE.
2. Place the switch in the FOOTPAD position to enable
FOOTPAD activation.
3. Step on the FOOTPAD to activate the scary sequence!
Footpads are sold separately and can be purchased at
www.tekkyaccessories.com
*
FOOTPAD IS NOT INCLUDED. MUST BE PURCHASED SEPARATELY.
OPTIONAL FOOTPAD SET UP