Tekky boogie man User manual

boogie man
INSTALLATION AND OPERATING INSTRUCTIONS
KEEP ALL PLASTIC AND WIRE PARTS AWAY FROM CHILDREN
1
A
A
A
A
A
A
A
A
B
2
3
A
A
A
A
A
A
A
A
4
A
A
A
A
A
A
A
A
1 2 3 4 5 6
7
8
1. UPPER BODY
2. PLASTIC BASE
3. WOODEN BASE
4. LEG POLES
5. UPPER POLES
6. PANTS WITH BRACKET
7. SHOES
8. 6V2A ADAPTER
B
5
B
B
B
B
CC
B
6
B
B
CC
7
D
C
D
DD
D
8
Snap lock four telescoping LEG POLES to the WOODEN
BASE. (Match ATO A) Press until it clicks into place.
Holding the four TELESCOPING LEG POLES near the base,
extend the poles upwards with your other hand until all four
poles are locked into place. The poles are fully extended
when you hear two audible clicks.
Slide SHOES over the LEG POLES connected to the
WOODEN BASE.
Slide PANTS WITH BRACKET over LEG POLES connected to
the WOODEN BASE.
Snap lock the PLASTIC BASE to LEG POLES . (Match Bto B)
Pull PANTS WITH BRACKET up and attach to holes on either
side of the MODULE inserting prongs facing down.
Firmly hold and extend both UPPER POLES. Poles are
fully extended when you hear an audible click.
Snap lock UPPER POLES to the module located inside
the clothes of the UPPER BODY.
(Match Dto D)
1.
2.
3.
4.
5.
6.
7.
8.
C
D
C
D

B
B
B
CC
C
C
9
Surface Washable Only.
ALL NEW MATERIALS : WOOD, METAL,
PLASTIC, FOAM, POLYESTER,
POLYESTER FIBER
Requires 4 ‘AA’Batteries (Not included)
or 6V 2A DC adapter (included)
BOOGIE MAN is a trademark of Tekky Toys.
Copyright © 2015 Tekky Toys.
All Rights Reserved.
MADE IN CHINA
WARNING
DO NOT TURN ITEM ON UNTIL YOU HAVE COMPLETELY
FINISHED ASSEMBLY.
STAY CLEAR OF ITEM WHILE OPERATING.
DO NOT PLACE ITEM ON UNEVEN GROUND.
DO NOT PLACE WEIGHT ON ITEM WHILE IN OPERATION
MODULE
BATTERY DIAGRAM
10.
11.
Connect 6V2A ADAPTER or insert 4 AA alkaline batteries into the
module located underneath the clothing of the UPPER BODY.
9. Connect UPPER BODY to PLASTIC BASE. Snap Lock UPPER POLES
to PLASTIC BASE. ( Match C to C)
FOOT
PAD
SPEAKER
VOLUME
CONTROL
DC 6V. 2A
FOOTPAD
ON
OFF
10
Turn the switch to the ON position to operate in Sound or Motion
activation mode. Make a loud sound (clap), or move in front of the
item to activate. Turn item OFF when not in use.
12. Adjust volume control knob as needed.
13. Pull down shirt and position arms out to the side as shown
in photo below.
FOOT
PAD
VOLUME
CONTROL
DC 6V. 2A
FOOTPAD
OFF
ON
11
SPEAKER
VOLUME
CONTROL
DC 6V. 2ASPEAKERV
FOOTPAD
ON
OFF
FOOT
PAD
Optional External Speaker Setup Instructions
EXTERNAL SPEAKER IS NOT INCLUDED. MUST BE PURCHASED SEPARATELY.
1.
2.
Plug speaker cord into the jack labeled
SPEAKER JACK located on top of the BASE.
Use volume knob on external speaker
to control volume levels.
VOLUME
CONTROL
DC 6V. 2ASPEAKERV
FOOTPAD
ON
OFF
FOOT
PAD
Optional Footpad Setup Instructions
Follow steps #1 through #10 on initial installation first.
Connect the cable from the optional footpad to the
jack labeled FOOTPAD located on the module.
Turn the switch on the base to the ‘ON’ position to
enable FOOTPAD activation.
Step on FOOTPAD to activate the scary sequence.
1.
2.
3. (Go to instruction 12 and continue setup)
visit us at tekkydesign.com
*Footpads are sold separately and can be purchased at www.tekkyaccessories.com
DO NOT RETURN THIS ITEM TO THE STORE!
If experiencing technical diculties, please go
to tekkydesign.com for assistance.
FOR FOOTPADS, ADAPTERS, AND ALL OTHER ACCESSORIES, PLEASE VISIT: www.tekkyaccessories.com