V-tech Toot Toot Drivers Assembly Instructions

Parent’s Guide
360° Loop Track
91-003783-000
UK

C
M
Y
CM
MY
CY
CMY
K
Grow with VTech(101x127)bw1P-V2.pdf 1 08/18/2014 9:29:01

2
2
2
INTRODUCTION
Race around and loop the loop with the Toot-Toot Drivers®360° Loop
Track. Press down on the launcher to see the Race Car race around
the tracks and through the flip-up gate! Even change the configuration
of the play set to create 2 different fun stunt show tracks.
SmartPointTM
Race Car
360° Loop1 SmartPointTM
Location

3
3
3
INCLUDED IN THIS PACKAGE
One launcher
One baseOne SmartPointTM
Race Car
One sign bracket
One launcher base
One uphill ramp
track
One arc track
One handleOne rotator
One downhill
ramp track
NOTE: This toy is not intended for teething.
One sign
One ¼ straight
track

4
4
4
WARNING:
All packing materials such as tape, plastic sheets, packaging locks,
removable tags, cable ties and packaging screws are not part of this
toy and should be discarded for your child’s safety.
NOTE: Please keep Parent’s Guide as it contains important information.
Adult assembly required.
For your child’s safety, please do not aim at faces when launching
the car.
Unlock the packaging locks:
Turn the packaging lock
anticlockwise several times.
Pull out and discard the packaging lock.
One handle
pedestal One ¼ straight
track
One label sheet
- One Parent`s Guide

5
5
5
GETTING STARTED
BATTERY INSTALLATION
Race Car
1. Make sure the unit is turned OFF.
2. Locate the battery cover on the bottom
of the Race Car. Use a screwdriver to
loosen the screw.
3. If used or spent batteries are present,
remove these batteries from the unit
by pulling up on one end of each
battery.
4. Install 2 new AAA (AM-4/LR03)
batteries following the diagram inside
the battery box. (The use of new
alkaline batteries is recommended
for maximum performance).
5. Replace the battery cover and tighten the screw to secure.
BATTERY NOTICE
• UsenewalkalinebatteriesorfullychargedNI-MH(NickelMetal-
hydride) rechargeable batteries for best performance.
• Useonlybatteriesofthesameorequivalenttypeasrecommended.
• Donotmixdifferenttypesofbatteries:alkaline,standard(carbon-
zinc) or rechargeable, or new and used batteries.
• Donotusedamagedbatteries.
• Insertbatterieswiththecorrectpolarity.
• Donotshort-circuitthebatteryterminals.
• Removeexhaustedbatteriesfromthetoy.
• Removebatteriesduringlongperiodsofnon-use.
• Donotdisposeofbatteriesinfire.
• Donotchargenon-rechargeablebatteries.
• Remove rechargeable batteries from the toy before charging (if
removable).
• Rechargeable batteries are only to be charged under adult
supervision.

6
6
6
Disposal of batteries and product
The crossed-out wheelie bin symbols on products and
batteries, or on their respective packaging, indicates they
must not be disposed of in domestic waste as they contain
substances that can be damaging to the environment and
human health.
ThechemicalsymbolsHg,CdorPb,wheremarked,indicate
that the battery contains more than the specified value of
mercury(Hg),cadmium(Cd)orlead(Pb)setoutinBattery
Directive(2006/66/EC).
The solid bar indicates that the product was placed on the
market after 13th August, 2005.
Helpprotecttheenvironmentbydisposingofyourproductorbatteries
responsibly.
Formoreinformation,pleasevisit:
www.recycle-more.co.uk
www.recyclenow.com

7
7
7
LABEL APPLICATION
Please stick the labels to the play set securely as
indicated on the following pages:
1
9
3
9
4
8
9 9 10
11 12
13
13
14
15
16
17
18
19
19
8
12
7
16
17
18
2
13 10
11
14
5
6
15

8
8
8
ASSEMBLY INSTRUCTIONS
360° Loop Track
With the VTech®Toot-Toot Drivers®360° Loop Track, safety
comesfirst.Toensureyourchild’ssafety,adultassemblyisrequired.
1. Connect the Uphill Ramp Track with the Downhill Ramp Track
as shown below.
2. Insert the Arc Track into the slot on both the Uphill Ramp Track
and the Downhill Ramp Track as shown below.
3. Insert the Launcher Base into the Launcher as shown below.

9
9
9
4. Insert the Launcher onto the Launcher Base as shown below.
5. Insert the Handle Pedestal onto the track as shown below.
6. Insert the Rotator and the Handle into the Handle Pedestal as
shown below.