Teknik 5427027 User manual

NOTE: THIS INSTRUCTION
BOOKLET CONTAINS IMPORTANT
SAFETY INFORMATION.
PLEASE READ AND KEEP FOR
FUTURE REFERENCE.
Prime Oak Hutch
Model 5427027
Knick-knack
paddywhack,
give your stu a home.
Teknik
www.teknikoffice.co.uk

Table of Contents Assembly Tools Required
Part Identification
Hardware Identification
Hardware Usage Guide
Assembly Steps
Français
Español
Safety
Warranty
3
4
5
6-22
23-25
26-28
29-30
31
Page 2
No. 2 Phillips Screwdriver
Tip Shown Actual Size
Hammer
Not actual size
Nail Holder (provided)
Tape Measure
Electric drill with 1/8" bit
(ONLY in indicated step)
Pencil

Part Identification
åWhile not all parts are labeled, some of the parts will have a label or an inked letter on the edge
to help distinguish similar parts from each other. Use this part identification to help identify similar parts.
Now you know
our ABCs.
A RIGHT END (1)
B LEFT END (1)
C LEFT UPRIGHT (1)
D RIGHT TOP MOLDING (1)
E LEFT TOP MOLDING (1)
F FIXED SHELF (1)
G LEFT ADJUSTABLE SHELF (1)
H FIXED SHELF MOLDING (1)
J ADJUSTABLE SHELF MOLDING (2)
K UPRIGHT MOLDING (2)
L LONG BRACE (1)
M FRONT TOP MOLDING (1)
N SHORT BRACE (2)
O BACK (1)
P TOP (1)
Q RIGHT UPRIGHT (1)
R RIGHT ADJUSTABLE SHELF (1)
A
B
C
D
E
F
G
H
J
KL
M
N
O
P
Q
R
N
J
K
Page 3

Hardware Identification
åScrews are shown actual size. You may receive extra hardware with your unit.
BLACK 9/16" LARGE HEAD SCREW - 7
1S BROWN 1-5/8" FLAT HEAD SCREW - 8 55S
MOLDING
CONNECTOR - 2
17F
CAM SCREW - 6
8F WOOD DOWEL - 4 15F
HIDDEN CAM - 6
1F
SILVER 1" LARGE HEAD SCREW - 8
102S
BRACKET CONNECTOR - 2
81G NAIL - 21 1N
CLIP - 7
67G37F TWIST-LOCK®FASTENER - 12
FURNITURE TIPPING
RESTRAINT KIT - 1
97
SHELF REST - 8
10R 105P TWIST-LOCK®
FASTENER COVER - 12
Page 4
SCREW COVER - 4
74P

Hardware Usage Guide
1. Insert the dowel end of the FASTENER into the
hole of the adjoining part.
NOTE: The dowel end of the FASTENER must
remain fully inserted in the hole of the adjoining
part while locking the FASTENER.
2. Tighten the FASTENER with a Phillips
screwdriver as tight as possible.
Dowel end
2.
Push a TWIST-LOCK® FASTENER
into the large hole in the part.
1.
HOW TO USE A TWIST-LOCK®FASTENER
Cam Screw
Hidden Cam
Arrow
Push a HIDDEN CAM into
the part. The arrow in the
HIDDEN CAM must point
toward the hole in the
edge of the board.
Hole
2. 3.
1
2
Insert the CAM SCREW into the HIDDEN CAM.
Tighten the HIDDEN CAM.
HOW TO USE A HIDDEN CAM & CAM SCREW
Turn the CAM SCREW until
the shoulder is against the
surface of the part.
1.
Page 5

Step 1
å Assemble your unit on a carpeted floor or on the empty
carton to avoid scratching your unit or the floor.
å To begin assembly, push twelve SAUDER TWIST-LOCK®
FASTENERS (37F) into the large holes in the ENDS (A and B),
UPRIGHTS (C and Q), and FIXED SHELF (F).
A
B
C
F
Q
37F
Do not tighten the TWIST-LOCK® FASTENERS in this step.
37F
Meet Parts (A and B). These components
have been engineered to be lighter,
stronger, faster… well ok. Not technically
faster. But definitely makes for a sturdier
hutch that’s easier to assemble and
friendlier to the environment.
Page 6
Some assembly
(and snacks) required.

å Turn six CAM SCREWS (8F) into the ENDS (A and B)
and UPRIGHTS (C and Q).
å Insert four WOOD DOWELS (15F) into the ENDS (A and B).
Step 2
A
B
C
Q
8F
8F
8F
15F
Page 7

å Slide the UPRIGHT MOLDINGS* (K) onto the notched
edges of the UPRIGHTS (C and Q).
å *U.S. Patent No. 5,499,886
å Slide a FIXED SHELF MOLDING* (H) onto the notched
edge of a FIXED SHELF (F).
å *U.S. Patent No. 5,499,886
Step 3
F
C
Q
H
K
K
Slide the UPRIGHT MOLDING (K) onto the notched edge.
These surfaces should be even.
Notched edge
Notched edge
Notched edge
The groove
is closer to
this edge.
These surfaces should be even.
The groove
is closer to
this edge.
The groove
is closer to
this edge.
Page 8
Surface with
TWIST-LOCK®
FASTENERS
Surface with
TWIST-LOCK®
FASTENERS
Surface with
TWIST-LOCK®
FASTENERS

å Push six HIDDEN CAMS (1F) into the BRACES (L and N).
Step 4
L
N
N
1F
Arrow
1F Arrow
Page 9

å Fasten the UPRIGHTS (C and Q) to the FIXED SHELF (F) and
LONG BRACE (L). Tighten four TWIST-LOCK® FASTENERS
and two HIDDEN CAMS.
Step 5
LF
H
C
Q
Surface with HIDDEN CAMS
Surface with
TWIST-LOCK®
FASTENERS
Surface with
TWIST-LOCK®
FASTENERS
Surface without
TWIST-LOCK®
FASTENERS
1
2
Page 10