Tenma 72-13160 User manual

Content
1 .Safety information -----------------------------------------------------------------------------------------------------1
2. IP Camera Tester Introduction---------------------------------------------------------------------------------------1
2.1 General -----------------------------------------------------------------------------------------------------------2
2.2 Packing list ------------------------------------------------------------------------------------------------------2
2.3 Function interface ----------------------------------------------------------------------------------------------3
3. Operation ----------------------------------------------------------------------------------------------------------------7
3.1 Installing the Battery-------------------------------------------------------------------------------------------7
3.2 Instrument connection -----------------------------------------------------------------------------------------8
3.2.1 IP camera connection ---------------------------------------------------------------------------------8
3.2.2 Analog camera connection---------------------------------------------------------------------------9
3.2.3 HD Coaxial camera connection ---------------------------------------------------------------------9
3.2.4 HDMI IN port ---------------------------------------------------------------------------------------- 10
3.3 OSD menu ----------------------------------------------------------------------------------------------------- 10
3.3.1 Lite mode & Normal mode------------------------------------------------------------------------- 11
3.3.2 Drop-down Menu------------------------------------------------------------------------------------ 13
3.3.3 Short cut-menu --------------------------------------------------------------------------------------- 14
3.3.4 Screen capture---------------------------------------------------------------------------------------- 16
3.3.5 TesterPlay --------------------------------------------------------------------------------------------- 16
3.3.6 Rapid video ------------------------------------------------------------------------------------------- 18
3.3.7 IP discovery------------------------------------------------------------------------------------------- 19
3.3.8 Rapid ONVIF test------------------------------------------------------------------------------------ 20
3.3.9 IP camera test----------------------------------------------------------------------------------------- 34
3.3.10 HDMI IN--------------------------------------------------------------------------------------------- 37
3.3.11 Video monitor test---------------------------------------------------------------------------------- 41
3.3.12 Color-bar generator (TV OUT)------------------------------------------------------------------ 50
3.3.13 SDI/EX-SDI Camera Test ( *Optional )----------------------------------------------------- 52
3.3.14 CVI camera test ( *Optional ) ----------------------------------------------------------------- 53

3.3.15 TVI camera test ( *Optional )------------------------------------------------------------------ 60
3.3.16 AHD camera test ( *Optional )---------------------------------------------------------------- 62
3.3.17 Network tool ---------------------------------------------------------------------------------------- 63
（1）IP address scan ------------------------------------------------------------------------------------- 63
（2）PING Test -------------------------------------------------------------------------------------------- 64
（3）Network test (Ethernet bandwidth test)--------------------------------------------------------- 65
（4）Port Flashing----------------------------------------------------------------------------------------- 68
（5）DHCP server----------------------------------------------------------------------------------------- 70
（6）Trace route ------------------------------------------------------------------------------------------- 70
（7）Link monitor----------------------------------------------------------------------------------------- 71
3.3.18 Rapid IP Discovery -------------------------------------------------------------------------------- 72
3.3.19 PoE power / DC12V 2A and DC 5V 2A USB power output------------------------------- 72
3.3.20 Cable Test-------------------------------------------------------------------------------------------- 74
3.3.21 RJ45 cable TDR test------------------------------------------------------------------------------- 75
3.3.22 Cable Tracer----------------------------------------------------------------------------------------- 78
3.3.23 TDR cable test ( *Optional )------------------------------------------------------------------- 79
3.3.24 PoE Voltage test------------------------------------------------------------------------------------ 82
3.3.25 12V power input test------------------------------------------------------------------------------- 83
3.3.26 Digital Multi-meter ( *Optional )------------------------------------------------------------- 84
3.3.27 Optical power meter ( *Optional )------------------------------------------------------------ 91
3.3.28 Visual Fault Locator ( *Optional )------------------------------------------------------------ 93
3.3.29 Audio Record --------------------------------------------------------------------------------------- 95
3.3.30 Data monitor ---------------------------------------------------------------------------------------- 95
3.3.31 Audio player----------------------------------------------------------------------------------------- 96
3.3.32 Media Player ---------------------------------------------------------------------------------------- 96
3.3.33 RTSP Player----------------------------------------------------------------------------------------- 97
3.3.34 Hikvision test tool---------------------------------------------------------------------------------- 98
3.3.35 Dahua test tool-------------------------------------------------------------------------------------101
3.3.36 Update-----------------------------------------------------------------------------------------------105

3.3.37 Office------------------------------------------------------------------------------------------------106
3.3.38 LED Flashlight-------------------------------------------------------------------------------------106
3.3.39 Browser ---------------------------------------------------------------------------------------------107
3.3.40 Notepad ---------------------------------------------------------------------------------------------107
3.3.41 System Setting-------------------------------------------------------------------------------------108
3.3.42 File explorer----------------------------------------------------Error! Bookmark not defined.
3.3.43 Theme -----------------------------------------------------------------------------------------------114
3. 4 Audio test ----------------------------------------------------------------------------------------------------117
3.5 HDMI output-------------------------------------------------------------------------------------------------117
3.6 PoE power output--------------------------------------------------------------------------------------------117
3.7 DC12V 2A power output ----------------------------------------------------------------------------------118
4. Specifications --------------------------------------------------------------------------------------------------------120
4.1 General Specifications--------------------------------------------------------------------------------------120
4.2 Multi-meter specifications ---------------------------------------------------------------------------------123
4.3 Optical power meter specifications ----------------------------------------------------------------------125
4.4 Visual fault locator specifications------------------------------------------------------------------------126

Page.1.
1 .Safety information
◆The tester is intended to use in compliance with the local rules for electrical usage and avoid use at
places which are inapplicable such as hospital, gas station etc.
◆When using electrical appliances basic safety precautions should always be followed.
◆Please operate according to this manual, otherwise the protection provided by the device will be
impaired or fail.
◆Check the test leads for damage, and case insulation condition before using. If you find any breakage,
damage or abnormality, or you consider the device is broken, stop using the device immediately.
◆There are no user-serviceable parts in this product. Refer servicing to qualified personnel.
◆Do not operate or store in an environment of high humidity or where moisture may enter the product.
◆Do not use the meter around explosive gas or vapour.
◆Do not use the product for any purpose other than that for which it is designed.
◆Don’t leave the tester unattended while charging and recharging. If the battery gets hot, the tester
should be powered off from the electric source at once.
◆The tester should not be charged over 8 hours.
◆Clean the meter with a clean, soft cloth.
◆Do not use any chemicals, abrasives or solvents that could damage the meter.
About Digital Multi-meter
◆Disconnect circuit power and discharge all high voltage capacitors before testing continuity, diode,
resistance, capacitance or current.
◆Before measuring current, check the fuses and turn the power to the circuit off before connecting the
meter to the circuit.
◆Do not connect the meter to voltage signals when the range selector is on current, resistance, diode or
continuity range.
◆Select appropriate test range for measurements.
◆Do not change the mode selector options during tests or measurements.
◆Ensure all inputs are less than the range selected otherwise it may cause electrical shock or damage.
◆Take caution when voltages are above 60V DC and 30V AC rms.
◆To avoid electrical shock and personal injury, do not attempt to measure voltage higher than 600V
AC/DC, although the readings may be obtained.

Page.2.
◆When using the test leads, keep your fingers behind the finger guards.
Visual laser sources
◆Do not point laser sources directly into your eyes or indirectly off reflective surfaces.
◆When not in use turn off and replace the protective cap.
2. IP Camera Tester Introduction
2.1 General
The 7 inch touch screen IP camera monitor is designed for maintenance and installation of IP cameras,
analog cameras, TVI, CVI AHD, SDI/EX-SDI cameras, as well as testing 4K H.264 /4K H.265 cameras
by mainstream. The 1920x1200 resolution enables it to display network HD cameras and analog
cameras in high resolution. The unit supports many ONVIF PTZ and analog PTZ controls. The
combination of touch screen and key buttons make the IP camera tester very user- friendly.
The tester is also a great tool for Ethernet network testing. It can test PoE power voltage, PING, and
search for an IP address. You can also use the blue cable tracer probe to locate individual connected
cables from a bundle of cables, and the tester can be used to test LAN cables for proper connection
termination. Other functions include providing 24W PoE power to your camera, HDMI IN and out,
CVBS loop test, testing IP and analog at the same time, an LED Flashlight, DC 12V 2A power output
and much more. Its portability, user-friendly design and many other functions make the IP tester an
essential tool for all installers or technicians.
2.2 Packing list
1). Tester
2). DC12V 2A power adapter
3) Network cable tracer/probe
4) Polymer lithium ion battery (7.4V DC 5000mAh)
5). BNC and RS485 cables
6). SC, ST Connector (Only for optical power meter）
7). Multi-meter test leads; one pair of red/black (only for the Multi-meter models)
8). Output Power cable
9). Audio cable

Page.3.
10). TDR alligator clamp (only for TDR models)
11). Safety cord
12). Tool bag
13). Manual
14).8GB SD card
2.3 Function interface

Page.4.
1 Press 2 seconds or more to turn on or off the device. Short press to illuminate the
menu display
2 Menu key; press to call shortcut menu
3 4xzoom image display
4 Far focus: Focus the image faraway
5 Near focus: Focus the image nearby
6 TELE: zoom in the image
7 WIDE: zoom out the image
8 Open/set ,Confirm the setting of parameters, open or enlarge the aperture
9 Close/Return: Return of cancel; close or decrease aperture.
10 Upward, set function or add parameter. Tilt the PTZ upward
11
Rightward, select the parameter whose value will be changed. Add the value of the
parameter. Pan the PTZ right
12 Leftward, select the parameter whose value will be changed
13
Downward, set function or reduce the value of the parameter. Tilt the PTZ
downward
14 Confirm key (Long press it to capture screen interface)
15 Return/Close : Return or close
16 Multimeter interface (Optional)
17 The charge indicator: it lights red while the battery is being charged. As the
charging is complete, the indicator turns off automatically
18 The RS485 data transmission indicator: it lights red while the data is being
transmitted
19 The data received indicator: it lights red while the data is being received
20 The power indicator: it lights green while the tester is powered on by the adapter

Page.5.
Top interface
Bottom interface
21 TDR cable test interface (Optional)
22 SDI input (BNC interface) ( Optional)
23 RS485 Interface: RS485communication for the PTZ
24 HDMI IN
25 Video signal output（BNC interface）/ cable tracer interface
26 CVBS input /AHD /TVI/CVI Coaxial interface (AHD /TVI/CVI Optional )
27 Optical power meter interface (Optional)
28 PoE power supply output or LAN test port (Use to test PoE or non-PoE IP camera)
29 PSE power sourcing equipment. Tests PoE voltage
30 DC 12V 2A power output , for provisional DC power supply
31 LED lamp
32 Visible red laser source emits Interface (Optional)
33 Power battery switch

Page.6.
34 DC 12V 2A charging interface
35 Audio input
36 Audio output and earphone interface
37 USB 5V 2A power output (used only for power, not data)
38 UTP cable port: UTP cable tester port/ Cable tracer port
39 Micro SD card moveable,(comes with 8GB, supports up to 32GB)
40 HDMI output interface

Page.7.
3. Operation
3.1 Installing the Battery
The battery main switch at the right-bottom corner of tester bottom。
“0”: Battery power off
“1”: Battery power on
The tester has a built-in lithium-ion polymer rechargeable battery. The tester’s bottom power should be
turned to “0” for safety during transportation (the factory default is “0”).
When using the instrument, switch power button to “1”, press the several seconds to turn
on/off tester. In general, the user does not need to turn on battery switch. When not in use for an
extended period, turn off the switch.
Notice: Use the original adaptor and connected cable of the device!
When the battery icon is full, or the charge indicator turns off automatically, it indicates the
battery charging is completed.
Notice: When the Charge Indicator turns off, the battery is approximately 90% charged.
The charging time can be extended for about 1 hour and the charging time within 12
hours will not damage the battery.
Notice: Press the key several seconds to restore the default settings when the
Instrument works abnormally.
Multi-meter: the red and black multi-meter probes must insert the correct corresponding port.
Warning: Do not insert a 6V source load into the
Instrument communication port, or you could damage
the tester.
Warnings: Do not insert multi-meter probes in the
current terminal to measure voltage.

Page.8.
3.2 Instrument connection
3.2.1 IP camera connection
Power an IP camera with an independent power supply, then connect the IP camera to the IPC tester’s
LAN port, if the link indicator of the tester’s LAN port is green and the data indicator flickers, it means
the IP camera and the IPC tester are communicating. If the two indicators don’t flicker, check if the IP
camera is powered on or the network cable is not functioning properly.
Note: 1) When the IP camera requires PoE power, the test can supply power through the IP tester’s
LAN port. Turn on or off the PoE power by clicking the icon “POE power output” in Normal mode, or
from the IP Camera Test app in Lite mode.
2) A PoE switch or PSE (power sourcing equipment) may be connected to the tester’s PSE port to
supply PoE power to the IP camera through the tester’s LAN port. A POE switch or PSE can on be used
when the tester’s PoE power is turned off. On this condition, the tester cannot receive data from IP
camera, but the computer connected to the PoE switch can receive the data via the tester.
Warning: PoE switch or PSE (power sourcing equipment) can only be connected to tester “PSE
IN” port; otherwise it will damage the tester.

Page.9.
3.2.2 Analog camera connection
(1) ) Connect the camera's video output to the IP tester’s VIDEO IN. The image will display on the
tester after pushing the PTZ icon.
(2) CCTV IP Tester “VIDEO OUT” interface connect to the Video input of monitor and optical video
transmitter and receiver, the image display on the tester and monitor.
(3) Connect the camera or the speed dome RS485 controller cable to the tester RS485 interface ,(Note:
positive and negative connection of the cable).
3.2.3 HD Coaxial camera connection
* SDI/EX-SDI, CVI, TVI, AHD camera are classified as HD coaxial cameras. Hereby the following
instruction of how to connect SDI camera to the tester is also applied to CVI, TVI, and AHD camera.

Page.10.
(1) Connect the SDI camera's video output to the IP tester’s “SDI IN” interface and the image will
display on the tester when choosing the “SDI” icon on the tester.
(2) Connect the SDI camera or the speed dome RS485 controller cable to the tester RS485 interface,
(Note: positive and negative connection of the cable).
3.2.4 HDMI IN
Attach a DVR or other device’s HDMI out port connect to tester’s HDMI in port and the tester will
display the input image.
3.3 OSD menu
Press the key 2 seconds to turn on

Page.11.
Press the key again to turn off
Short press the key to enter sleep mode, press it again to test.
If tester works abnormally and cannot be turned off, Press the key several seconds to turn
off and the tester will reset.
3.3.1 Lite mode & Normal mode
Lite mode: Easily find corresponding apps
In Lite mode, Press the icon several seconds, can move the icon to other apps.
In Lite mode, click the finger icon in the lower right corner to release locked icons, move icons
and change sequence of icons.
Normal mode
To change to Normal mode, choose the “Theme” tab and then press “Desktop style” to toggle
between Normal mode and Lite mode.

Page.12.
In Normal mode, press icon several seconds so icon can be dragged within a page or moved to other
pages.
This allows the user to individualize the tester to specific requirements.
Create New Folder: Drag the icon to the folder in top right corner, enter the folder name. Icon will be
auto placed in the new named folder.

Page.13.
Press the folder several seconds, to change the folder name, you can move the icon out of folder, the
folder will be auto deleted until move out all icons.
Select Icons to enter, if quit, please click
Click “SD card” from “Settings” menu to install or remove SD card.
3.3.2 Drop-down Menu
Press and slide at top of screen twice to open shortcut menu. The shortcut menu includes POE power
output, IP settings, HDMI IN, CVBS, LAN info, Settings, etc.

Page.14.
HDMI: Click HDMI IN to enter the HDMI input mode, where the tester can display a dual test
window (picture in picture) with IP & HDMI inputs or Analog & HDMI inputs.
CVBS: Click icon “CVBS” to enter CVBS input mode where the tester can display both an IP
and analog camera at the same time.
TV OUT: Click “TV out” to enter floating window (picture-in-picture) of the color-bar
generator to send through the BNC/CVBS output to a video monitor for color bar testing
of monitor and cable.
LAN: Display network port or WIFI connection real-time upload and download speeds and
other network parameters.
Brightness: Set brightness
Settings: Enter settings interface.
IP: Enter IP Settings interface.
POE OUTPUT: Turn on or off the tester’s POE power output to the LAN port.
WLAN: Turn on WLAN net and displays current WLAN status.
3.3.3 Short cut-menu
The shortcut menu can be accessed by pressing the tester’s “menu” key.

Page.15.
Press the key to turn it on, arrow keys to switch functions, and to enter app; tap
outside the menu to exit.
The shortcut menu can be modified from the “Settings” icon. Enter the Short cut setting and long
press any app in the “All applications” list and it will auto move to shortcut menu. To delete any app
in the short cut menu, press the app for several seconds and it will be deleted.

Page.16.
3.3.4 Screen capture
Long press the “enter” key to capture screen interface and save it at any time.
User can go to “File Explorer” to view documents, pictures, videos and screenshots.
3.3.5 TesterPlay
TesterPlay is a mobile screen projection (for android versions only).
The tester creates a WIFI hotspot to connect mobile phone to the tester’s WIFI hotspot, or the tester and
mobile phone connect to the same WiFi network. Tap icon “ ”, then select “TesterPlay” app to
enter where the meter generates two-dimensional code. Scan the code with mobile phone and download
and install the client software. The tester’s screen can be viewed in real-time projection.