Teradek Bolt User manual

Bolt
Quick Start Guide
Panel Antenna Version 4

PHYSICAL PROPERTIES
A: 2dBi Omnidirectional antenna
B: RP-SMA connectors (horizontal)
C: RP-SMA connectors (vertical)
D: Battery plate
E: Yoke assembly
F: 3/8” Light stand adapter
C BB
A
DE
F

TABLE OF CONTENTS
Teradek Bolt Panel Antenna v.4.......... 2
Power and Connect ......................... 3
Antenna Receive Pattern .................. 4
Mounting ....................................... 5

WHAT’S INCLUDED
1x Bolt Array Antenna Assembly (Gold or V-mount)
5x RP-SMA Male to RP-SMA Male 4in/10cm Cable
TERADEK BOLT PANEL ANTENNA V.4
The Bolt Panel Antenna v.4 is your go-to solution for cutting through wireless
interference in crowded environments. When attached to a Bolt 4K receiver, the antenna
provides an extremely robust, directional signal that will ensure your transmission arrives
uninterrupted. The Bolt Panel Antenna oers a more resilient wireless transmission,
especially in challenging RF conditions, by focusing the signal and reducing interference.
As a result, you may achieve a boost in the reception range but it will not be above the
maximum range.
1x 2dBi Omnidirectional Antenna
2

Connect the output from your video source to either the SDI or HDMI input on the transmitter.
POWER AND CONNECT
Attach antennas to the transmitter.
Mount the receiver to the back of the Panel Antenna.
Mount the receiver to the back of the antenna, then connect the five RP-SMA connectors to
the center connectors labeled V using the included extension cables. If the transmitter is using
horizontal antennas, attach the receiver’s two outward connectors to the antenna’s two external
connectors labeled Hinstead (see images below).
Connect power to both the transmitter and receiver with the included A/C adapter or optional battery
plate accessory. If using a battery plate, connect a compatible (AB Gold mount or V-Lock) battery.
Move the power switches on both the transmitter and receiver to the ON position. Video appears
within a few seconds.
V configuration H + V configuration
1
3
2
4
6
5
3

ANTENNA RECEIVE PATTERN
The Bolt Panel Antenna has a built-in directional antenna with a receive pattern that varies based on
its distance from the transmitter. The horizontal receive angle measures 55° at 5,000 ft (1.5 km), 104°
at 4,000 ft (1.25 km), and is eectively omni directional at up to 500 ft (150 m). The vertical receive
angle measures 20° at any distance.
500 ft (150 m) ~ 360°
5,000 ft (1.5 km) ~ 55°
4,000 ft (1.25 km) ~ 104°
20°
4

• Orient the transmitter and receiver so they are parallel to
each other.
The Bolt Panel Antenna has three 3/8” threaded holes: One on the bottom for mounting the included
light stand adapter or any 3/8” mounting accessory, and one on each side to mount to a yoke mount
bracket assembly.
MOUNTING
• Mount the Panel Antenna vertically, keeping it clear of any obstructions.
• For best results, orient the Panel Antenna so the front
(with the Teradek logo) has a clear line−of−sight to
the transmitter.
DO NOT OVERTIGHTEN SCREWS
INSERTED INTO THE RECEIVER’S 3/8”
THREADED HOLES. Doing so can damage the receiver’s
chassis, voiding the warranty.
CAUTION:
5

Teradek regularly releases new firmware versions to improve performance, add features, or fix vulnerabilities.
teradek.com/pages/downloads contains all the latest firmware and software updates.
Visit teradek.com/contact for tips, information, and to submit help requests to Teradek’s support team.

7
© 2021 Teradek, LLC. All rights reserved. v1