Teufel Impaq 3000 Manual

5.1 Home cinema system with blu-ray receiver
Impaq®3000
Technical description and operating instructions
91607 GB 20101105.indd 191607 GB 20101105.indd 1 05.11.2010 9:56:10 Uhr05.11.2010 9:56:10 Uhr

2• Impaq®3000
Contents
General notes and information . . . . . . . . . . . . . . . . . . 3
Safety notes . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4
Caution icons . . . . . . . . . . . . . . . . . . . . . . . . . . 4
Safety notes . . . . . . . . . . . . . . . . . . . . . . . . . . . 4
Overview. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 6
Check to be sure. . . . . . . . . . . . . . . . . . . . . . . . 6
Control elements and connections . . . . . . . . . . . . . . . . 7
Front side. . . . . . . . . . . . . . . . . . . . . . . . . . . . . 7
Rear side . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 7
Fernbedienung . . . . . . . . . . . . . . . . . . . . . . . . . 8
Setup and connection . . . . . . . . . . . . . . . . . . . . . . . . . 9
Setup location . . . . . . . . . . . . . . . . . . . . . . . . . 9
Setting up the speakers . . . . . . . . . . . . . . . . . . . 9
Connecting the speakers . . . . . . . . . . . . . . . . . . 10
Antennas . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 10
FM antenna . . . . . . . . . . . . . . . . . . . . . . . . . . 10
AM antenna. . . . . . . . . . . . . . . . . . . . . . . . . . . 10
Network/Internet . . . . . . . . . . . . . . . . . . . . . . . 11
Television/projector. . . . . . . . . . . . . . . . . . . . . . 11
Inputs for devices source . . . . . . . . . . . . . . . . . . 11
Connecting to a power supply . . . . . . . . . . . . . . 11
Remote control . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 12
IBasic functions . . . . . . . . . . . . . . . . . . . . . . . . . . . 13
Sensor buttons . . . . . . . . . . . . . . . . . . . . . . . . . 13
Activating and Deactivating . . . . . . . . . . . . . . . . 13
Selecting a source. . . . . . . . . . . . . . . . . . . . . . . 13
Adjusting the volume . . . . . . . . . . . . . . . . . . . . . 13
Mute . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 13
Main menu. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 14
Menu "Display" . . . . . . . . . . . . . . . . . . . . . . . . 15
Menu "Audio" . . . . . . . . . . . . . . . . . . . . . . . . . 15
Menu "Language". . . . . . . . . . . . . . . . . . . . . . . 15
Menu "Parental control". . . . . . . . . . . . . . . . . . . 16
Menu "System". . . . . . . . . . . . . . . . . . . . . . . . . 16
Menu "Network" . . . . . . . . . . . . . . . . . . . . . . . 17
Audio settings . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 18
LEVEL . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 18
HDMI AUDIO OUT . . . . . . . . . . . . . . . . . . . . . . 18
TESTTONE . . . . . . . . . . . . . . . . . . . . . . . . . . . . 18
LIPSYNC . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 18
SURROUND. . . . . . . . . . . . . . . . . . . . . . . . . . . 18
TONE . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 18
DISTANCE . . . . . . . . . . . . . . . . . . . . . . . . . . . . 18
Special function buttons . . . . . . . . . . . . . . . . . . . . . . . 19
Button "Resolution" . . . . . . . . . . . . . . . . . . . . . . 19
Button "Surround". . . . . . . . . . . . . . . . . . . . . . . 19
Button "Tone" . . . . . . . . . . . . . . . . . . . . . . . . . . 19
Button "Bass" . . . . . . . . . . . . . . . . . . . . . . . . . . 19
Buttons "A B C D" . . . . . . . . . . . . . . . . . . . . . . . 19
BD/DVD/CD mode . . . . . . . . . . . . . . . . . . . . . . . . . . . 20
Suitable BDs/DVDs/CDs . . . . . . . . . . . . . . . . . . 20
Handling BDs/DVDs/CDs . . . . . . . . . . . . . . . . . 20
Inserting a BD/DVD/CD . . . . . . . . . . . . . . . . . . 20
Ejecting a BD/DVD/CD DVD . . . . . . . . . . . . . . . 20
Radio Playback . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 21
USB mode . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 22
Playback functions . . . . . . . . . . . . . . . . . . . . . . . . . . . 23
General playback information . . . . . . . . . . . . . . 23
Additional display for file playback . . . . . . . . . . 23
BD and DVD Playback. . . . . . . . . . . . . . . . . . . . 23
Jumping to track, chapter or placemark. . . . . . . . 23
Picture-in-picture (PIP) . . . . . . . . . . . . . . . . . . . . 23
Selecting files . . . . . . . . . . . . . . . . . . . . . . . . . 24
Playback list. . . . . . . . . . . . . . . . . . . . . . . . . . . 24
Slide show . . . . . . . . . . . . . . . . . . . . . . . . . . . . 25
Troubleshooting . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 26
Care and cleaning . . . . . . . . . . . . . . . . . . . . . . . . . . . 27
Protecting the environment . . . . . . . . . . . . . . . . . . . . . 28
Technical data . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 28
Index . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 29
91607 GB 20101105.indd 291607 GB 20101105.indd 2 05.11.2010 9:56:11 Uhr05.11.2010 9:56:11 Uhr

• Impaq®3000 3
Notice
The information in this document may be changed with-
out prior notice and in no way constitutes any liability on
the part of Lautsprecher Teufel GmbH.
No part of these instructions may be reproduced in any
form or be broadcasted in any way electronically, me-
chanically, by photocopy or recording without the written
permission of Lautsprecher Teufel GmbH.
© Lautsprecher Teufel GmbH
Version 1.1, September 2010
Trademarks
© All trademarks are the property of their respective
owners.
Dolby
Manufactured under licence from Dolby Laboratories.
"Dolby", "Pro Logic" and the double D symbol are trade-
marks of Dolby Laboratories.
DTS
Manufactured under licence with the US patent numbers:
5,451,942 5,956,674; 5,974,380; 5,978,762; 6,487,535
and other U.S and international patents, which have
been issued and are pending. DTS and DTS Digital
Surround are registered trademarks and the DTS logos
and the DTS symbol are trademarks of DTS, Inc. ©1996 –
2008 DTS Inc. All rights reserved.
Original packaging
If you wish to exercise your eight-week right of return, we
ask that you be absolutely sure to hold onto the packag-
ing. We can only accept the return of the device WITH
THE ORIGINAL PACKAGING.
Empty boxes are not available!
Complaints
In case of complaint we will need the following informa-
tion to process your enquiry:
1. Invoice Number
Can be found on the sales slip (enclosed with the
product) or on the order confirmation received as a PDF
document, e.g. 4322543.
2. Serial number or batch number
Visible on the back side of the device,
e.g. serial #: IL30009440122A-123
Many thanks for your support!
Contact
For questions, suggestions or any other issues please
contact our customer service department:
Lautsprecher Teufel GmbH
Gewerbehof Buelowbogen · Buelowstrasse 66
10783 Berlin (Germany)
Tel.: 00800 - 200 300 40 (free of charge)
Fax: +49 (0)30 - 300 930 930
www.teufelaudio.com
Proper use
Only use the unit as described in these instructions. Any
other use will be deemed as not in accordance with the
instructions and may lead to damage to property or even
persons. The manufacturer accepts no liability for dam-
age caused by use not in accordance with the instruc-
tions.
The unit is intended for private use.
Before operating the unit for the first time please
read the safety notes and operating instructions
carefully. This is the only way to use all functions
safely and reliably.
Keep the operating instructions safe and pass them on to
anyone who may own the unit after you.
General notes and information
91607 GB 20101105.indd 391607 GB 20101105.indd 3 05.11.2010 9:56:11 Uhr05.11.2010 9:56:11 Uhr

4• Impaq®3000
Safety notes
Caution icons
You will find the following caution icons used in these
instructions:
Danger High risk!
Failure to observe the warning may result in
severe personal injury or death.
Attention Moderate risk!
Failure to observe the warning may result in
property damage.
Minor risk!
Points which should be observed when hand-
ling the unit.
Safety notes
Danger Risk of electric shock!
Faulty installation of electrical equipment or
mains voltage which is too high can cause
electric shocks.
The device is only suitable for use with a power supply•
voltage of 220 V –240 V ~ / 50Hz/60 Hz.
If the unit’s case or mains cable is defective or shows•
other signs of visible damage, disconnect the mains
adapter immediately from the socket and do not oper-
ate the device.
If the device produces smoke, a burning odour or emits•
unusual sounds, immediately disconnect it from the
mains and discontinue use.
The standby button does not disconnect the device•
from the power supply. For this reason, connect it to an
easily accessible socket so that you can quickly discon-
nect it from the power supply in the event of faults.
Never open the unit case.•
Repairs may only be carried out by an authorised
specialist workshop. Only use parts which conform
with the original unit specifications. There are electrical
and mechanical parts in this unit which are essential in
order to avoid exposure to sources of danger.
Do not insert any objects through the vent slots in the•
case.
Only use the unit in indoor areas.•
Do not operate the unit in moist areas and protect it from•
drops of water or splash water.
Also take care not to stand vases or other containers of
liquid on or near the unit in order to avoid liquid getting
into the case. If water or other foreign bodies should
enter the case, disconnect it immediately from the mains
power supply and remove any batteries. Send the unit to
our service address.
Never touch the mains adapter with wet hands.•
Check the unit regularly for damage.•
Danger Danger to children!
Children can become trapped in the packing
film when playing and suffocate.
Do not allow children to play with the unit or the pack-•
ing film. Danger of suffocation.
Ensure that children do not remove small parts from•
the unit or take them off of the unit (e.g. control knobs
or plug adapters). They could swallow the parts and
choke. Never allow children to use electrical devices
without supervision.
Danger Danger to eyes and skin!
If the disc tray is open and the lock is disabled,
an invisible laser beam or visible laser light is
emitted.
Do not look into the beam, even if you are using opti-•
cal instruments.
Danger Danger to hearing!
Loud noise may lead to hearing loss.
Particularly when a subwoofer in "Stand-by/
Auto On" mode is activated by bass impulse and has
been set to maximum volume, very high noise pressure
may be produced. This may also have psychological
consequences as well as cause physical injury. Children
and pets are particularly at risk.
Set your signal source unit volume control to a low•
setting.
When the volume is set high, always keep a certain•
distance from the unit and never place your ear directly
on the speaker.
To avoid damage to health, avoid extended listening at•
high volume.
Danger Danger of chemical burns!
Leaking battery acid may lead to chemical
burns.
Do not allow battery acid to come into contact with•
skin, eyes or mucus membranes. In case of contact
with acid rinse the affected location immediately with
plenty of plain water and if necessary see a doctor.
91607 GB 20101105.indd 491607 GB 20101105.indd 4 05.11.2010 9:56:11 Uhr05.11.2010 9:56:11 Uhr

• Impaq®3000 5
Danger Danger of injury/damage!
Incorrect location may result in damage.
Never use the unit unmounted in vehicles, in instable•
locations, on wobbly stands or furniture, with attach-
ment fixtures that are too small etc. The unit could
topple over or fall, injuring persons or causing damage
to the unit itself.
Arrange the speakers so that they cannot be knocked•
over accidentally and make sure that the cables do not
pose a trip hazard.
Ensure that any wall mounting is performed in a profes-•
sional manner.
Only use suitable wall brackets for mounting. Check•
the carrying capacity of the walls.
Only set up the device and the speakers on stable,•
level surfaces.
Do not place the unit near sources of heat (e.g. heat-•
ers, ovens, other heat generating equipment such as
amplifiers etc.)
Danger Danger of explosion!
Batteries and rechargeable batteries may
explode if overheated.
Never attempt to recharge normal batteries.•
Do not expose batteries or rechargeable batteries to•
heat and never throw them in open fire.
Attention Fire hazard!
Improper use may lead to damage or fire.
Do not place open flames such as burning candles or•
similar on the unit.
Ensure sufficient ventilation.•
Do not place the unit in direct sunlight.•
Do not cover the ventilation slots with curtains, cloths,•
newspapers or similar. Heat build-up inside the unit
can shorten the lifetime of the unit.
Attention Risk of damage!
Power overload due to lightning strike may
damage or destroy the unit.
If the unit is to be left unsupervised for a long period•
(e.g. during a holiday), or if a thunderstorm is forecast,
disconnect it from the mains power supply.
If the device is subjected to warm temperatures after•
being cold (e.g. after transport), condensation may
occur inside of it. Wait at least 2 hours before you con-
nect and activate it.
Old, used batteries may leak.•
Remove the batteries from the remote control if you do
not use them for a prolonged period of time.
91607 GB 20101105.indd 591607 GB 20101105.indd 5 05.11.2010 9:56:11 Uhr05.11.2010 9:56:11 Uhr

6• Impaq®3000
Product contents
햲1 x Blu-ray receiver IP 3000 BR
햳4x Front/rear speakers IP 3000 FR
햴1x Center speaker IP 3000 C with table stand
햵1x Subwoofer IP 3000 SW
햶1 x Remote control
햷2 x Battery Micro/AAA for remote control
햸1 x AM antenna
햹1 x FM throw-out aerial
햺Speaker cables red/black 3m
Speaker cables white/black 3m
Speaker cables green/black 5m
Speaker cables blue/black 5m
Speaker cables grey/black 5m
Speaker cables purple/black 5m
햻1 x power cord
Check to be sure
Check that all items have been delivered and that•
nothing is damaged.
If the delivery is incomplete or you find damage•
sustained in transit, do not operate the unit but contact
our service department (see page 3).
Overview
햲
햳
햴
햵
햶
햷
햸
햹
햺
햻
91607 GB 20101105.indd 691607 GB 20101105.indd 6 05.11.2010 9:56:11 Uhr05.11.2010 9:56:11 Uhr

• Impaq®3000 7
4 048945 547507
Control elements and connections
Front side
124765
Rear side
Pos Name Description
1Pro Save radio station
2Src Source device selection
3USB USB connection
4Headphones Headphones connection
5 – Volume + Volume buttons
6Skip forward
7Skip back
8Stop button
98 3101112131415
16 17 18 19 20 21 22
232425262728
Pos Name Description
9Playback/pause
10 Disk eject button
11 – Standby display
12 IR Infrared receiver
13 – Display panel
14 – Disk compartment
15
Switch the device on or to standby
Pos Name Description
16 SPEAKERS Speaker connections
17 AUX IN 1-3 Input jacks for analogue audio
source devices
18 COAXIAL IN Input jack for digital audio signals
via coaxial cable
19 VIDEO Output jack for TV/projector with
FBAS video
20 L R Output jacks for analogue stereo
sound
21 ETHERNET Network/internet connection
22 AM ANT Antenna connection AM
Pos Name Description
23 FM ANT Antenna connection FM
24 HDMI 1 + 2 Input jacks for digital source de-
vices with HDMI connection
25 HDMI OUT Output jack for TV/projector with
HDMI connection
26 Y CB/PB
CR/PR
Output jacks for TV/projector with
component video
27 OPTICAL IN Input jack for digital audio signals
via optical lines
28 – Connector jack for power cord
91607 GB 20101105.indd 791607 GB 20101105.indd 7 05.11.2010 9:56:12 Uhr05.11.2010 9:56:12 Uhr

8• Impaq®3000
Remote control Pos Name Description
29 Open DVD tray
30 Audio Source Select audio input
31 Radio Select "FM" or "AM" radio
32 1...0 Number buttons
33 Clear/Delete Clear button
34 Skip back
35 Skip forward
36 Playback/pause
37 Frame button
38 Mute speakers
39 + Volume – Adjust the volume
40 Popup Menu Access BD popup menu
41 ▲Preset+ Station memory/navigation up
42 ▶ Tune+
Frequency forward, navigation right
43 Enter Select button
44 Return Exit setting/menu
45 RDS Display
Additional display/RDS information
46 A B C D Control buttons for BD programs
47 Secondary
Audio Switch sound for picture-in-picture
48 PIP Picture-in-picture function for BD
49 Bass Bass boost on/off
50 Tone Adjusting the sound
51 Surround Setting ambient sound
52 A - B Repeat section
53 Zoom Enlarge image
54 Resolution Set resolution
55 Stereo/Mono
Audio
Radio: Switch between stereo/
mono, audio settings
56 Subtitle Switch subtitles
57 ▼Preset– Station memory/navigation down
58 ◀ Tune– Frequency back, navigation left
59 Disc Menu BD/DVD menu
60 Main Menu Main menu
61 Audio Setup-
Program
Set audio, Radio: Occupy station
memory slot
62 Set repeat
63 Stop playback
64 Fast rewind
65 Fast forward
66 Search
Auto Scan
Select BD/DVD chapter, automati-
cally save radio station
67 AV Source Select audio/video source
68 Switch the device on or to standby
31
55
56
57
58
59
60
61
62
63
64
66
65
67
68
30
29
36
37
38
39
40
41
42
46
43
49
50
51
52
53
44
48
45
47
35
54
34
33
32
91607 GB 20101105.indd 891607 GB 20101105.indd 8 05.11.2010 9:56:13 Uhr05.11.2010 9:56:13 Uhr

• Impaq®3000 9
Setup and connection
Setup location
Select a stable, level base.•
Make sure that the environment is clean and free from•
dust.
Avoid placing the unit close to sources of heat or in•
direct sunlight.
Arrange the connector cables so that they do not pose•
a trip hazard.
Do not place any heavy objects on top of the cables or•
the unit.
There should be approximately 10 cm of space around•
the device to enable adequate air circulation.
Setting up the speakers
The following data concern an "ideal home cinema", in
which the viewer or listener sits in a central position at a
sufficient distance in front of the television or screen (see
the adjacent graphic) and no objects (tables or the like)
are located in between. Unfortunately, the room, furnish-
ings or one’s partner do not always allow for optimum
arrangement.
The following general rule applies: You can always
experiment on what works best in your listening room in
terms of sound and appearance based on our recommen-
dations. Let your ears (and eyes) be the judge!
Center speakers
Place the center speaker on its support foot in an interme-
diate position directly under the monitor or screen.
Front speakers
The front speakers are set up to the right and left of the
screen or hung at a height of approx. 40 to 120 cm. They
should be in line with the center speaker and form an
equilateral triangle with the listener – the so-called stereo
triangle (distance from the listener = distance between the
speakers). The speakers should project sound directly into
the room or slightly towards the listener.
Rear speakers
The rear speakers should be set up or hung at head
level (140 to 210 cm) to the side of the listener and point
towards the listener. The distance to the listener should be
at least 100 cm and 10 cm to the back wall of the room.
You can also place the rear speakers behind the listener
at head level and point them towards the screen.
Subwoofer
You should place the Subwoofersubwoofer on the floor
close to the television, ideally somewhere between the
front speakers.
TV
Stereo triangle
Front FrontCenter
Rear
Rear
Rear
Rear
Subwoofer
91607 GB 20101105.indd 991607 GB 20101105.indd 9 05.11.2010 9:56:13 Uhr05.11.2010 9:56:13 Uhr

10 • Impaq®3000
Connecting the speakers
To connect the speakers, use the enclosed cables if
possible or equivalent, two-core speaker cable with a
diameter of at least 1 mm2. You can order these cables in
our webshop (www.teufelaudio.com) in the "Accessories"
area.
The coloured connector terminals 16 "Speakers" for the
six speakers are located on the back of the receiver:
Colour Speakers Description
white/black Front left FL
red/black Front right FR
green/black Center CENTER
blue/black Rear left SL
grey/black Rear right SR
purple/black Subwoofer SUBWOOFER
The speaker connector terminals and the enclosed speaker
cables have the same colour.
Make sure the polarity is correct!
Connect the respective terminals with the like
colour. Otherwise the sound quality will suffer.
Now push down the respective connector
terminal lever and run the cable end into the
corresponding opening. Releasing the lever
locks the cable in place.
Antennas
Danger Risk associated with lightning strike!
If you are using outdoor or roof antennas, be
absolutely sure that the antenna has lightning
protection.
FM antenna
Connect the antenna for receiving FM stations to the jack
23 "FM ANT". This may be a roof/outdoor antenna or
a cable television connection. You will need a coaxial
cable for this.
If an antenna connection is not available at your setup
location, you can use the enclosed throw-out aerial 햹.
Insert the antenna plug into the jack 23 "FM ANT" and
adjust the position of the throw-out aerial until you have
the best possible reception. Then fix the antenna in place
with tape or a nail.
AM antenna
The enclosed antenna 햸is intended for receiving
medium-wave stations (AM). You can setup this antenna
to be freestanding or screw it onto a (cabinet) wall.
Connect the connector cable of the antenna with the
jacks 22 "AM ANT" on the back of the receiver. Depress
each lever of the connector terminal and insert the cable
end in the opening. Releasing the lever secures the cable
in place.
햸
4 048945 547507
16 22
23
91607 GB 20101105.indd 1091607 GB 20101105.indd 10 05.11.2010 9:56:14 Uhr05.11.2010 9:56:14 Uhr

• Impaq®3000 11
Network/Internet
The receiver must be connected to a network to enable
the internet functions (BD live) and program updates.
Connect your network or router to the jack 21 "ETHER-
NET" with a network cable.
Television/projector
You can connect a television set and/or projector to the
following outputs:
25 HDMI OUT
Digital video and audio signals via an HDMI cable.
26 Y CB/PB CR/PR
Analogue component picture signal via the triple RCA
cable. When connecting, take note of the colour of the
jacks (green, blue and red). Analogue sound is emitted
via the RCA jacks 20 "L R".
19 VIDEO
Analogue picture signal (FBAS) via an RCA cable. Here,
analogue sound is also emitted via the RCA jacks 20 "L R".
Ideally, you should use the HDMI output 25 as only the
signals of the HDMI inputs 1 and 2 are emitted here. The
HDMI inputs cannot be used when connecting via one of
the other outputs.
Inputs for devices source
The receiver has two inputs for digital HDMI picture and
audio sources (HDMI 1 + 2). An optical and coaxial dig-
ital audio output as well as three analogue audio inputs
are also available (AUX IN 1–3).
You can connect the audio output of your television to
one of these inputs in order to enjoy receiver audio output
from television programs. For this, consult the instruction
manual for your television.
24 HDMI 1 und 2
You can connect a source device with a digital and audio
signal to each of these jacks. A HDMI cable is required
for this.
Important
You can only use these HDMI inputs if the
playback device (TV or projector) is connected
via HDMI.
18 COAXIAL IN
You can connect coaxialthe coaxial digital audio output
of a source device here. To do so, you will need a co-
axial cable with RCA plugs.
27 OPTICAL IN
Here, you can optical connect the optical digital audio
output of a device. To do so, you will need an optical ca-
ble with a Toslink plug. Your source device requires either
an optical 3.5 mm plug or a Toslink plug.
17 AUX IN 1 bis 3
You can connect a source device with analogue audio to
each of these inputs. You will need a double RCA cable
(L and R).
Connecting to a power supply
Connect the power jack• 28 with a power socket using
the power cord 햻.
19 20 21
2526
17 18
2427
4 048945 547507
28
91607 GB 20101105.indd 1191607 GB 20101105.indd 11 05.11.2010 9:56:14 Uhr05.11.2010 9:56:14 Uhr

12 • Impaq®3000
You will need two micro-type or AAA batteries with 1.5
Volt (included in the product contents) in order to operate
the remote control.
Inserting batteries
Press the latch of the battery compartment on the back1.
side of the remote control towards the arrow and take
off the cover.
If applicable, remove any old batteries (please observe2.
the notes on page 28).
Insert the batteries in the battery compartment as3.
shown in the figure.
Place the cover back on the compartment and push it4.
closed.
Functionality
The remote control transmits the control signals by means
of infrared light. For this, you must point the front of the
remote control towards the receiver. Make sure that the
infrared light is not obstructed by objects.
Fluorescent lamps and energy/saving lamps installed in
the direct vicinity may affect the functions of the remote
control or even impair them.
Remote control
91607 GB 20101105.indd 1291607 GB 20101105.indd 12 05.11.2010 9:56:15 Uhr05.11.2010 9:56:15 Uhr

• Impaq®3000 13
Basic functions
Sensor buttons
The buttons on the front of the receiver are sensor but-
tons: Gently touching them is enough to trigger a switch
command..
Activating and Deactivating
With the button• 15 or 68 " ", you can switch your
receiver to operating or standby mode.
The red LED is on in standby mode• 11.
Standby mode does not disconnect the device from the
power supply. Pull the power plug out of the socket to
completely deactivate the device.
Selecting a source
After turning the device on, the last source device se-
lected is activated.
Pushing the button• 2"SRC" switches the source in
the following order: DISC (BD/DVD/CD and USB),
HDMI 1, HDMI 2, COAX IN, OPTI IN, AUX IN 1,
AUX IN 2, AUX IN 3, FM radio, AM radio.
Or you switch the source with the direct selection but-•
tons:
67 "AV source" – DISC or USB, HDMI 1, HDMI 2
31 "Radio" – FM, AM
30 "Audio Source" – COAX IN, OPTI IN, AUX IN 1,
AUX IN 2, AUX IN 3
The selected source is shown on the display panel 13.
Adjusting the volume
Increase volume: Push button• 5"Vol +" or button 39
"Volume +".
Decrease volume: Push button• 5"Vol –" or button 39
"Volume –".
The selected volume is shown on the display panel 13 in
the range 0 (low) to 40 (high).
Mute
Pushing the button• 38 " " turns the sound off. The
message "MUTE ON" appears on the display panel
13.
Reactivating the sound: Push the button• 38 " " again
or change the volume.
2
5
15
31
39
38
30
67
13
68
91607 GB 20101105.indd 1391607 GB 20101105.indd 13 05.11.2010 9:56:15 Uhr05.11.2010 9:56:15 Uhr

14 • Impaq®3000
Main menu
You can set most functions of your receiver using the main
menu. You can control the menu with the remote control.
The menu is rendered on the connected television.
Important
The menu functions are only available if "DISC"
is selected as the source.
Both devices must be activated, the image of the receiver
must be visible on the television.
Push the button• 67 "AV source" several times if necessary
in order to select "DISC" as the source.
If the playback of an inserted BD or DVD begins, push the•
button 60 "Main Menu". The main menu will appear on
the screen.
With the navigation buttons• 41 " ▲ " and 57 " ▼ " select the
item "Settings" and push the select button 43 "Enter" or
the navigation button 42 " ▶ ".The menu will open.
Select the desired submenu using the navigation buttons•
41 " ▲ " and 57 " ▼ " and push the select button 43 "Enter"
or the navigation button 42 " ▶ ".The submenu will open
and an overview of the current settings will appear ini-
tially. You can open other submenus and make settings.
Push the button• 44 "Return" or the navigation button 58
" ◀ " to return to the previous menu.
If the menu is in German ("Einstellungen" instead of "Set-
tings"), change the language to English as follows:
1.Select the item "Einstellungen".
2.Select the item "Sprache".
3.Select the item "OSD-Menü".
4.Select the item "English".
The menu language will now switch to English.
5.Push the button 44 "Return" until only the main menu is
visible.
67
57
58
59
60
40
41
42
43
44
91607 GB 20101105.indd 1491607 GB 20101105.indd 14 05.11.2010 9:56:16 Uhr05.11.2010 9:56:16 Uhr

• Impaq®3000 15
Menu "Display"
You can define the settings for the connected
picture playback device (e.g. TV, projector) here.
"TV standard"
Setting the cross colouring system for the connected
television set:
NTSC – American standard
PAL – European standard
In case of doubt, consult the instruction manual of your
television set.
"Resolution"
Set the resolution of the television set for HD playback.
Possible values:
HDMI Auto, 1080p, 1080i, 720p, 576p, 576i
HDMI Auto automatically selects the highest possible
resolution.
Note: The resolution 1080p is only available at the HDMI
output.
You can also make this setting with the special function
button 54 "Resolution" (see "Special function buttons" on
page 19).
"Picture format"
Setting the display on the television:
16:9 Widescreen – 4:3 films are displayed on a 16:9 TV
set in full height and with stretched width.
16:9 Pillarbox – 4:3 movies are displayed on a 16:9-TV
set in full height with a black bar on the left and right.
4:3 Pan Scan – 16:9 movies are shown on a 4:3 televi-
sion set in full height, but the sides are cut off.
4:3 Letterbox – 16:9 movies are displayed on a 4:3
television set with their full width and black bars on the
top and bottom.
"Movie mode"
Movies are recorded on blu-ray discs with full resolution
and 24 frames/second (1080p24). Not all television
sets are capable of displaying these frame rates and the
picture will flicker as a result. If this is the case, turn off
the movie mode.
Note: 1080p is only emitted via HDMI. A maximum of
1080i is available at the component output, independ-
ently of the setting "Movie mode".
Menu "Audio"
Here, you can define the audio settings for BD
and DVD playback.
"PCH Downsampling"
Sets the sampling rate for the audio signal. Possible
values:
Off – not implemented (192 kHz)
96 kHz – corresponds to DVD quality
48 kHz – corresponds to CD quality
"Digital output"
Specifies the audio output at the HDMI output 25 "HDMI
OUT". Possible values:
PCM 7.1 – Signal is mixed at 7.1 and transmitted as PCM.
Bitstream HD – Relays the data stream of the blu-ray disc
unchanged.
Bitstream Legacy – Relays the data stream of the blu-ray
disc in Legacy Audio format. Suitable for Dolby Digital
5.1 or 6.1 and DTS 5.1.
Bitstream Mixed – Relays the data stream of the blu-ray
disc mixed or coded in a single data stream. Suitable for
Dolby TrueHD and DTS HD Master Audio.
"Dynamic control"
This function is only active with Dolby Digital and
amplifies excessively quiet passages while weakening
excessively loud passages. Possible values: On, Off,
Automatic.
Menu "Language"
Here, you define the language for menus, subti-
tles and playback.
OSD menu – Language for the menu functions (German
or English).
Disc menu – language for the DVD menus. Multiple
languages are available to the extent your DVD supports
them.
Audio – Language for DVD playback. Multiple languages
are available if supported by the DVD.
Subtitles – Subtitle language for DVD playback. Multiple
languages are available if supported by the DVD. The
setting "Off" deactivates the subtitles.
91607 GB 20101105.indd 1591607 GB 20101105.indd 15 05.11.2010 9:56:16 Uhr05.11.2010 9:56:16 Uhr

16 • Impaq®3000
Menu "Parental control"
Child lock for BD/DVD playback. Some BD/
DVDs are labelled for specific age groups and
cannot be played in a certain setting. Unfortunately,
many BD/DVDs do not have proper protection and many
self-burned copies and video movies also lack such
protection.
"Child lock"
On – This indicates that the protection is activated.
Unlocking Off – This deactivates protection. To do so,
the password must be entered with the number buttons 32
"1...0".
"Age rating"
Set the protection level. Eight levels are available, which
correspond to the recommendations of the MPAA (Motion
Picture Association of America) for rating movies:
1 – Kid safe, suitable for children.
2 – G (General Audience), suitable for all age groups.
3 – PG (Parental Guidance), under adult supervision.
4 – PG-13 (Parental Guidance 13), for at least 13 years of
age and under adult supervision.
5 – PG-R (Parents Guidance - Restricted), only under
parental supervision.
6 – R (Restricted), for persons aged 17 years and older
under parental supervision.
7 – NC-17 (No Children 17 and under admitted), for
persons aged 18 years and older.
8 – Adult, for adults only.
"Parent password"
Change the Password: Enter the new password with the
number buttons 32 "1...0" and confirm with the select
button 43 "Enter".
Be sure to remember the new password! In an emer-
gency, you can reset the receiver to the factory default
settings (see next section).
Menu "System"
Here, you can define the general settings for
the receiver.
"Disk Autoplay"
After inserting a BD/DVD, the playback will automatically
start right away.
"BD-Live internet access"
Control access to the internet via the blu-ray disc.
Restrict access – Access only possible if you request it.
Always access – The BD may access the internet at any
time.
Block access – The BD may not load any data from the
internet.
Note: The BD live functions are only possible if a USB
stick with sufficient storage space has been inserted (see
page 22).
"BD-Live memory"
The free storage space on the inserted USB stick is dis-
played or "No USB" is displayed.
"Clear blu-ray memory"
Clear the space occupied by BD live on the USB stick.
"Screen saver duration"
After the period of inactivity set here, the receiver will
dim the screen e.g. to prevent burn-in with plasma
screens.
Possible values: 5, 10, 20, 30 minutes. If set to "Off", the
screen saver is deactivated.
"Update via network"
With this function, you can load a new version of the op-
erating system software for your receiver via your internet
connection if one is available.
First, the currently installed and update version will be
displayed on your screen. Select the item "Cancel" with
the navigation buttons 58 "◀" and 42 "▶" to abort the
process or "OK" to perform the update. Then push the
select button 43 "Enter".
The update will take several minutes, do not turn the
device off or interrupt the internet connection during this
time. In the process, observe the notices on the screen.
After the update, set the receiver back to the factory
default settings.
"Factory default settings"
This allows you to reset all receiver settings to the factory
default settings. After this has been done, you have to
make your individual settings again.
91607 GB 20101105.indd 1691607 GB 20101105.indd 16 05.11.2010 9:56:17 Uhr05.11.2010 9:56:17 Uhr

• Impaq®3000 17
Menu "Network"
Here, you select the settings for the internet
connection. When the menu is accessed, a new
menu appears initially:
Hard-wired• – Set network
Network test• – Check connection
"Network test"
The receiver performs several tests and displays the re-
spective result on the screen. You can end the tests at any
time with "Cancel".
If all tests have been performed successfully, the internet
connection is functional. Otherwise the receiver provides
notes on potential error sources on the screen.
"Hard-wired"
Once opened, the current "IP settings" are displayed
initially:
Link status:• "Link Up" states that a network device
is electrically linked to the receiver while with "Link
Down" no or a defective connection is displayed. Only
for the purpose of information, cannot be changed.
• MAC address: This is the hardware address of the
Ethernet interface, which is important when connecting
to a router. Only for the purpose of information, cannot
be changed.
IP mode:• "Dynamic" – The receiver automatically
requests (viaDHCPDHCP) the required settings for a
router. Recommended setting, then no other entries
are required. Prerequisite: An active DHCP server (e.g.
router) on the network.
"Manual" – The IP address and all other values have
to be set. These settings should only be made by a
qualified professional. Use the number buttons on the
remote control for input.
• IP address: The network address for the receiver
consisting of four numbers between 0 and 255, e.g.
192.168.001.100.
Net mask:• With the net mask, the receiver recognises
which addresses it can access on its own network and
which can only be accessed via the gateway (router).
Consists of four numbers, each between 0 and 255,
e.g. 255.255.255.0.
• Gateway: Network address of the gateway (router),
which controls the connection to the internet.
Primary DNS:• Network address of the domain name
server, which detects the corresponding IP address for
domain names (e.g. www.teufelaudio.com). Compara-
ble with a phone book.
Secondary DNS:• As before, used in the event the
primary DNS fails.
To cancel, push the button 44 "Return".
To adopt the entries, select the item "Apply" and push the
select button 43 "Enter". The receiver then automatically
performs a network test (see above).
57
58
60
41
42
43
33
32
91607 GB 20101105.indd 1791607 GB 20101105.indd 17 05.11.2010 9:56:17 Uhr05.11.2010 9:56:17 Uhr

18 • Impaq®3000
Audio settings
You can access the audio settings by pushing the button
61 "Audio Setup". The menus are shown on the display
panel so there is no need to turn on the TV set or projec-
tor.
LEVEL – Adjust the volume of the individual speakers.
HDMI AUDIO OUT – Activate/deactivate sound transmis-
sion at the HDMI output.
TESTTONE – Set the volume of the individual speakers
using a test tone.
LIPSYNC – Set the delay for sound output.
SURROUND – Set the surround sound.
TONE – Set the sound.
DISTANCE – Set the signal travelling times for the speakers.
Select the desired submenu with the navigation buttons
41 "▲" and 57 "▼" and push the select button 43 "Enter".
The device switches back to normal operation after six
seconds of button inactivity.
LEVEL
You can increase or decrease the relative volume for
each speaker here.
1.With the navigation buttons 41 "▲" and 57 "▼" select
the desired speaker:
C– Center
FL – Front left
FR – Front right
SW – Subwoofer
SL – Rear left
SR – Rear right
2.With the navigation buttons 58 "◀" and 42 "▶" set the
relative volume in the range from "–10" to "+10".
3.To finish, push the button 44 "Return".
HDMI AUDIO OUT
Switch the sound transmission at the HDMI output 25
"HDMI OUT" "ON" or "OFF". When playing movies you
do not have to mute the television in order to hear the
sound from the receiver speakers.
TESTTONE
Adjusting the volume with testtone. As described previ-
ously in the section "LEVEL", you can increase or de-
crease the relative volume for each speaker here. In the
process, however, audio playback is replaced with a test
tone (white noise). The test tone stops as soon as you quit
the submenu.
LIPSYNC
Digital image processing in the television set requires a
certain amount of time. To keep the picture and sound
synchronous, television sets delay the sound by a few
milliseconds. To ensure that the sound of your receiver is
also synchronous, you can set the audio delay of your
receiver between 0 and 120 ms here.
The current value in millseconds (ms) appears on the•
display panel.
With the navigation buttons• 58 "◀" and 42 "▶" you
can now set the audio delay between 0 and 120 ms.
SURROUND
Briefly tipping the navigation buttons 58 "◀" and 42 "▶"
switches between the available modes:
"5.1 CH" 5.1 channel Surround sound
"DPLII" Dolby® ProLogic 2.
"STEREO" Stereo playback.
TONE
With the navigation buttons 41 "▲" and 57 "▼", select
the desired range for sound control:
Basslow tones (bass tones)
Treblehigh tones
With the navigation buttons 58 "◀" and 42 "▶" you can
now set the selected range from "–10" (decrease) to
"+10" (increase).
DISTANCE
Different distances between the speakers and the listen-
ing position may interfere with the perception of surround
sound. To compensate for these run time differences, set
the distances from the listening position to each speaker
from 0 to 400 cm here.
1. With the navigation buttons 41 " " and 57 " " select
the desired speaker:
C– Center
FL – Front left
FR – Front right
SW – Subwoofer
SL – Rear left
SR – Rear right
2. With the navigation buttons 58 " " and 42 " " set the
distance from the listening position from "0" to "400"
in 20 cm increments.
3. To finish, push the button 44 "Return".
57
58
60
41
42
43
91607 GB 20101105.indd 1891607 GB 20101105.indd 18 05.11.2010 9:56:18 Uhr05.11.2010 9:56:18 Uhr

• Impaq®3000 19
Special function buttons
Button "Resolution"
By pushing the button 54 "Resolution" you can set the
resolution of the television set for HD playback. Possible
values:
HDMI Auto, 1080p, 1080i, 720p, 576p, 576i
HDMI Auto automatically selects the highest possible
resolution.
Note: The resolution 1080p is only available at the HDMI
output.
Button "Surround"
Repeatedly tipping the button 51 "Surround" switches
surround sound:
"5.1 CH" 5.1 channel surround sound
"DPLII" Dolby® ProLogic 2
"STEREO" Stereo playback
Button "Tone"
Sound control. Select the desired range by pushing the
button 50 "Tone" several times:
Bass low tones (bass tones)
Treble high tones
With the navigation buttons 58 "◀" and 42 "▶" set the
selected range from "–10" (decrease) to "+10" (increase).
Button "Bass"
Activate and deactivate the extra low tone (bass) boost
by pressing the button 49 "Bass".
Buttons "A B C D"
With the coloured buttons 46 "A B C D", you control the
menus of interactive blu-ray discs.
58 42
46
49
50
51
54
91607 GB 20101105.indd 1991607 GB 20101105.indd 19 05.11.2010 9:56:18 Uhr05.11.2010 9:56:18 Uhr

20 • Impaq®3000
Suitable BDs/DVDs/CDs
Only use commercially-available BDs/DVDs/CDs,•
which feature one of the adjacent symbols.
BDs/DVDs/CDs that contain files in the following for-•
mats are readable: CD audio, VCD, SVCD, DVD video,
BD video, MP3 and JPEG.
Normal BDs/DVDs/CDs with diameters of 80 and 120•
mm can be used.
Burned BDs/CDs/DVDs are normally readable.•
However, an excessively high burning speed or "low-
quality" blank CDs may cause problems in this respect.
Unfortunately, the only solution here is trial and error.
CDs that are produced for industrial use cannot always•
be read.
Handling BDs/DVDs/CDs
Each BD/DVD/CD is encased in a resistant plastic layer
that protects it against external influences. However, you
must always protect the disc against dirt and scratches.
Your receiver can compensate small flaws on the BD/
DVD/CD. Larger scratches or other damages may result
in "hanging" or similar errors. Also observe the notes on
the CD case for proper handling of BDs/DVDs/CDs!
Inserting a BD/DVD/CD
Attention Risk of damage!
Do not, in any case, insert multiple BDs/CDs/
DVDs on top of one another. Do not insert any
objects other than BDs/CDs/DVDs.
1. Push the button 10 or 29 " ". The tray 14 will eject to
the front and at the same time, "DISC" is selected for
the source.
2. Carefully place the BD/DVD/CD with the labelled side
up in the tray recess.
3. Push the button 10 or 29 " ". The tray 14 closes and
the CD is read. With some DVDs, playback automati-
cally begins after a few seconds. If instead the menu
appears, select the item "BD-ROM" with the navigation
buttons 41 "▲" and 57 "▼" and push the select button
43 "Enter".
You can control the BD/DVD menu with the navigation
buttons and the select button 43 "Enter".
The playback functions for CD and USB are identical
and are described in the section "Playback functions" on
page 23.
BD/DVD/CD mode
Ejecting a BD/DVD/CD DVD
1. Push the button 10 or 29 " ". The DVD tray ejects to
the front.
2. Take the DVD/CD out of the tray.
3. Push the button 10 or 29 " ". The CD tray will close.
57
29
41
43
1014
91607 GB 20101105.indd 2091607 GB 20101105.indd 20 05.11.2010 9:56:18 Uhr05.11.2010 9:56:18 Uhr