The Outdoor Plus OPT-BP24SQDSSE110 User manual

SQUARE DROPIN PAN &
SQUARE SS BULLET BURNER
OPTBP24SQDSSE110
RECTANGULAR DROPIN PAN
& ‘H’ SS BULLET BURNER
OPTBP1260RDSSE110
INSTALLATION & OPERATION MANUAL
PLUG & PLAY TO LOW VOLTAGE
PANS & BURNERS
INSTALLER: Leave this manual with the appliance. | CONSUMER: Retain the manual for future reference.
PHONE: [phone]
EMAIL: [e-mail]
ADDRESS: 701 S DUPONT AVE. ONTARIO, CA 91761 U.S.A.
WEBSITE: THEOUTDOORPLUS.COM
ROUND FLAT PAN &
TRIPLE ‘S’ SS BULLET
BURNER
OPTBFP24RSSE110
DANGER: Carbon Monoxide Hazard
This appliance can produce carbon monoxide which has no odor.
Using it in an enclosed space can kill you.
Never use this appliance in an enclosed space such as a camper, tent,
car or home.
Installation
We suggest that our products be installed by professionals that are
locally licensed by the authority having jurisdiction in gas piping.
Service
We suggest that our products be serviced by a professional certified in
the US by the National Fireplace Institute (NFI) as NFI Gas Specialists.
DANGER: FIRE OR EXPLOSION HAZARD
If you smell gas:
»Shut off gas to the appliance.
»Extinguish any open flame.
»If odor continues, leave the area immediately.
»Aer leaving the area, call your gas supplier or fire department.
Failure to follow these instructions could result in fire or explosion, which could cause
property damage , personal injury, or death.

2THEOUTDOORPLUS.COM | [phone] | [e-mail]
SECTION 1
WARNINGS
THIS SECTION OUTLINES WARNING ASSOCIATED WITH INSTALLATION, USE, AND OPERATION.
SECTION 1  WARNINGS
This is a Safety Alert Symbol
When you see this symbol on the fire pit insert, or in this manual, look for one of the following signal
word panels alerting you to the potential for personal injury, death or major property damage.
WARNING: FOR OUTDOOR USE ONLY
Installation and service must be performed by a qualified installer, service agency, or
the gas supplier.
DANGER  FIRE OR EXPLOSION HAZARD
If you smell gas:
1. Shut off gas to appliance.
2. Extinguish any open flame.
3. If odor continues, leave the area immediately.
4. After leaving the area, call your gas supplier or Fire department.
Failure to follow these instructions could result in fire or explosion, which could cause
property damage, personal injury, or death.
WARNING: Do not store or use gasoline or other flammable vapors and liquids, In
the vicinity of this or any other appliance.
An LP-Cylinder not connected for use shall not be stored in the vicinity of this or any
other appliance.
For use with Natural or Propane gas only. NO SOLID FUELS TO BE USED WITH THIS SYSTEM.
WARNING: If the information in this manual is not followed exactly, a fire or
explosion may result causing property damage, personal injury, or loss of life.
CALIFORNIA PROPOSITION 65 WARNING
This product can expose you to Carbon Monoxide, which is known
to the state of California to cause cancer and birth defects or other
reproductive harm. (For more information, go to: www.p65warnings.ca.gov)

3
EXPERT TECHNICAL SUPPORT | MADE IN THE U.S.A. | 701 S. DUPONT AVE. ONTARIO, CA 91761 U.S.A.
SECTION 1
WARNINGS CONT’D.
THIS SECTION OUTLINES WARNING ASSOCIATED WITH INSTALLATION, USE, AND OPERATION.
* EXCEPT AS AUTHORIZED BY ANSI Z223.1 / NFPA 58

4THEOUTDOORPLUS.COM | [phone] | [e-mail]
SECTION 2
IMPORTANT SAFETY INFORMATION
TECHNICAL SUPPORT, SYMBOL LEGEND, SAFETY INFORMATION FOR INSTALLERS & END-USERS.
SECTION 2  IMPORTANT SAFETY INFORMATION
Instructions are also available at theoutdoorplus.com, Please carefully follow the instructions in
this manual to prevent personal injury or property loss. Instructions are updated as needed. It is the
installer’s responsibility to periodically review instruction for applicable updates.
The steps listed as:
WARNINGS: Contains information critical to the safe installation and operation of the fire pit.
WARRANTY REQUIREMENT: Must be strictly followed to qualify for product warranty. Warranty will
be void if not followed.
IMPORTANT: Are notes and insights to help ensure product satisfaction and serviceability.
WARNINGS:
It is the installer’s responsibility to ensure a safe installation and to educate the end user as to
proper operation. Leave this manual with the end user.
Never alter product or configuration in any way.
We suggest that our products be installed by professionals that are locally licensed by the
authority having jurisdiction in gas piping. We suggest that our products be serviced annually by a
professional certified in the US by the National Fireplace Institute (NFI) as NFI Gas Specialists or in
Canada by WETT (Wood Energy Technical Training). Installer must follow all instructions carefully
to ensure proper performance and safety.
The Outdoor Plus Company, Inc. is not responsible for your actions.
Product is not intended to be a starter for wood or any other combustibles.
Only use gas/fuel type specified for this fire pit see label on the fire pit control Box.
Verify correct gas/fuel type and pressure. Never use an alternative fuel to include bio-fuel, ethanol,
lighter fluid or any other fuel.
Gas pressure and type should be checked prior to use and installation.
DO NOT USE this appliance if any part has been under water. Immediately call a qualified service
technician to inspect the appliance and to replace any part of the control system and any gas
control which has been under water.
IT IS THE RESPONSIBILITY OF THE INSTALLER TO FOLLOW:
The National Fuel Gas Code, ANSI Z223.1/NFPA 54 or International Fuel Gas Code.
The National Electrical Code, ANSI/NFPA 70.
Local Codes
SUPPLY PRESSURE MIN/MAX:
Natural Gas:
Supply Pressure:
Minimum: 3.5” W.C. .87 kPa
Nominal: 7" W.C. 1.74 kPa
Maximum: 14" W.C. 3.48 kPa
Liquid Propane Gas:
Supply Pressure:
Minimum: 8" W.C. 1.99 kPa
Nominal: 11" W.C. 2.73 kPa
Maximum: 14" W.C. 3.48 kPa

5
EXPERT TECHNICAL SUPPORT | MADE IN THE U.S.A. | 701 S. DUPONT AVE. ONTARIO, CA 91761 U.S.A.
TABLE OF CONTENTS
DIRECTORY OF PAGES & SECTIONS
SECTION 1  WARNINGS .............................................................................................................3
SECTION 2  IMPORTANT SAFETY INFORMATION................................................................5
SECTION 3  COMPONENTS OVERVIEW .................................................................................6
SECTION 4  OPERATION SEQUENCE ......................................................................................8
SECTION 5  SELECTING THE LOCATION ...............................................................................9
SECTION 6  ENCLOSURE CONSTRUCTION ......................................................................... 10
SECTION 7  PREPLANNING CHECKLIST ............................................................................. 11
SECTION 8  INSTALLATION INSTRUCTIONS....................................................................... 12
SECTION 9  FIRE MEDIA USAGE.............................................................................................17
SECTION 10  PARTS LIST ........................................................................................................ 19
SECTION 11  OPERATION & USAGE .......................................................................................20
SECTION 12  TROUBLESHOOTING ........................................................................................22
SECTION 13  MAINTENANCE..................................................................................................25
SECTION 14  REPLACEMENT PARTS ....................................................................................27
SECTION 15  CLEARANCE FROM COMBUSTIBLES ............................................................28
SECTION 16  WARRANTY INFORMATION............................................................................. 31

6THEOUTDOORPLUS.COM | [phone] | [e-mail]
SECTION 3
COMPONENTS OVERVIEW
THIS SECTION OUTLINES THE FEATURES OF THE PLUG & PLAY TO LOW VOLTAGE PANS & BURNERS
SECTION 3  ELECTRONIC IGNITION VALVE OVERVIEW
Installation must conform with local codes or, in the absence of local codes, with the
National Fuel Gas Code, ANSI Z223.1 / NFPA 54, or International Fuel Gas Code.
The appliance when installed, must be electrically grounded in accordance
with local codes, or in the absence of local codes, with the National
Electrical Code, ANSI/NFPA 70; or the Canadian Electrical Code, CSA C22.1,
if applicable.
When an appliance is for connection to a fixed piping system, the installation must conform
with local codes, or in the absence of local codes with the National Fuel Gas Code, ANSI
Z223.1 * NFPA 54; National Fuel Gas Code; Natural Gas and Propane Installation Code, CSA
B149.1; or Propane Storage and Handling Code, CSA B149.2, as applicable.
»Certified to ANSI Z21.97-(2017) / CSA 2.41-(2017)
»-20° to 175° temperature range.
»Durable connections designed to resist outdoor
conditions.
»TC Flame-sense system.
»Hot Surface Igniter (HSI).
»LED diagnostics.
»Electronics are certified for CAN/CSA-E60730-1,
ANSI Z21.20-2014, CAN/CSA-C22.22 No.60730-2-
5-14, UL 60730-2-5 Edition 3, & UL 60730-1.
»12 or 14 VAC for installations within 5 feet of
water. 110V for installations must be farther than
5 feet from water.
»Potted control module to protect against
moisture and damage.
»Hot Surface Ignition (HSI), provides stable burner
ignition in harsh conditions.
»Thermocouple Flame Sense, fast responding and
resistant to wind, moisture and corrosion.
»LED diagnostics for field service and
troubleshooting.
»The manual key valve is CSA Certified to ANSI
Z21.15/CSA9.1
»The pilot is CSA Certified to ANSI Z21.20
»Coils are encapsulated to protect against
moisture.
»Pilot has robust flame pattern, wind resistant.
»Pilot injectors are stainless steel.
»Thermocouple is nickel plated for durability.
»Hot Surface Igniter (HSI) with protective cage.
»Hot Surface Igniter (HSI) connection is
waterproof.
»The Power Wire connector is waterproof.
GAS VALVE AND PILOT COMPONENTS
ELECTRONICS
COMPONENTS OVERVIEW

7
EXPERT TECHNICAL SUPPORT | MADE IN THE U.S.A. | 701 S. DUPONT AVE. ONTARIO, CA 91761 U.S.A.
SECTION 3
COMPONENTS OVERVIEW CONT’D.
THIS SECTION OUTLINES THE FEATURES OF THE PLUG & PLAY TO LOW VOLTAGE PANS & BURNERS
Installation or repair should be performed by a qualified service technician who is locally licensed. The appliance
should be inspected before use and at least annually by a qualified technician.
DO NOT remove any decal/rating plates from the Electronic Ignition Valve. A gas shut off must be installed
outside the exterior of the fire feature for emergency shut off and maintenance. A sediment trap is highly
recommended to alleviate any problems from debris or sediment in the gas line. It is the installers responsibility
to ensure the fuel supply and line are adequate to supply the maximum BTU for the burner used.
Note: a heat shield/plate MUST be installed between the Electronic Ignition Valve and the burner ring to avoid
over heating.
The Electronic Ignition Valve box is pre-mounted to the burner or burner & pan combination.
The Electronic Ignition Valve is designed to automatically close the gas valve and shut down should temperatures
exceed 175° Fahrenheit. To keep the unit cool, proper ventilation and a heat shield must be provided.
The Outdoor Plus Recommends a Stainless Steel Whistle-Free Flex Hose to eliminate the noise.
GAS CONNECTION
PILOT ASSEMBLY CONNECTIONS
We pre-assemble the pilot on top of the burner pan and in that configuration, the pilot line, thermocouple
and igniter lead should be lowered through a hole in the pan prior to connecting to the control box. The
pilot comes pre-assembled from the factory, so the installer can simply connect the assembly to the
main control box. The igniter has a “shaped” push on waterproof connector ensuring that is can only be
connected the correct way. Push this black plastic connector parts firmly together until it locks in place.
Gently tug on wires to assure connection is secure. The flexible corrugated pilot tube has a flare fitting
that should be connected 1/4 turn past hand tight. Please double check to ensure the fitting is snug both
into the control box and the flare connection. The thermocouple should now be connected. It screws onto
the 11/32” brass fitting on the control box closest to the black connector. It should be snug, but do not
over-tighten.
Next, you may mount the pilot to the burner pan. The shield is designed with perforated material which you
can use to secure to the pan with self tapping screws. The installer can determine the best placement for the
pilot depending on the burner configuration keeping the pilot within 1” from a burner port for quick ignition.
Once all connections are complete, it is highly recommended to perform a leak test. Turn on the gas supply
and using gas test solution or soapy water solution, spray the gas connections on the Electronic Ignition Valve
including the pilot connector to ensure it is leak free.
PLUG & PLAY TO LOW VOLTAGE
ELECTRONIC IGNITION COMPONENT
BURNER
PILOT ASSEMBLY
Electronic
Ignition Valve
GAS SUPPLY LINE
BURNER PAN/PLATE
110V ELECTRICAL
SUPPLY

8THEOUTDOORPLUS.COM | [phone] | [e-mail]
SECTION 4
OPERATION SEQUENCE
THIS SECTION DEMONSTRATES THE OPERATION SEQUENCE OF OUR PLUG & PLAY TO LOW VOLTAGE PANS & BURNERS.
SECTION 4  OPERATION SEQUENCE

SECTION 5
SELECTING THE LOCATION
THIS SECTION DEMONSTRATES LOCATION REQUIREMENTS & WARNINGS
SECTION 5  SELECTING THE LOCATION
WARNINGS:
All fire pits, match lit kits, spark ignition, safety pilot and Electronic Ignition Components are
designed and intended for outdoor use only.
All fire pits must have a gas shutoff on the outside of the exterior of the fire pit to allow for
emergency shut off and maintenance. DO NOT PLACE ON TOP OF NON-COMBUSTIBLE FLOORING.
Select a location where the fire pit can be attended during operation. Never leave an operating
fire pit unattended or by someone not familiar with its operation or emergency shut off locations.
Both children and adults should be alerted to the hazards of high surface temperatures and
should stay away to avoid burns and clothing ignition.
Young children should be carefully supervised when they are in the area of fire pit.
Clothing or other flammable materials should not be placed on or near fire pit.
Fire pits create very high temperatures - Combustibles must be located far enough away that
there is no risk of ignition.
IMPORTANT:
It is recommended that material such as granite, marble or other dense stone be kept away from
heat and especially flame due to risk of cracking. Manufacturer is not responsible for damage.
Select a location with proper drainage.
Choose a location that allows easy access for installation and maintenance of the fire pit.
Pick a location that allows sufficient horizontal room to enjoy the fire pit while allowing a safe
distance from the heat and flame.
CLEARANCE FROM COMBUSTIBLES  UP TO 65K BTUS  SEE SECTION 15
Under Valve Box When Applicable 2” For Drainage
Sides Surrounding Fire Pit 36” From Structure or Combustibles
Overhead Clearance Min. 84” Overhead Clearance
CLEARANCE FROM COMBUSTIBLES  66K TO 200K BTUS  SEE SECTION 15
Under Valve Box When Applicable 2” For Drainage
Sides Surrounding Fire Pit 48” From Structure or Combustibles
Overhead Clearance NO OVERHEAD CONSTRUCTION
CLEARANCE FROM COMBUSTIBLES  201K TO 400K BTUS  SEE SECTION 15
Under Valve Box When Applicable 2” For Drainage
Sides Surrounding Fire Pit 48” From Structure or Combustibles
Overhead Clearance NO OVERHEAD CONSTRUCTION
WARNING: Venting is required to dissipate heat and any residual fuel. Failure to
provide proper ventilation could result in overheating and or explosion. See Proper
Venting topic in the Enclosure Construction Section.

10 THEOUTDOORPLUS.COM | [phone] | [e-mail]
SECTION 6
ENCLOSURE CONSTRUCTION
THIS SECTION OUTLINES THE CONSTRUCTION OF THE FIRE FEATURE ENCLOSURE REQUIREMENTS & WARNINGS
SECTION 6  ENCLOSURE CONSTRUCTION
WARNINGS:
 All fire pits must have a gas shutoff on the outside of the exterior of the fire pit to allow for
emergency shut off and maintenance.
 Always use proper materials and construction for gas supply, power and enclosure.
 The enclosure must incorporate 1 vent on at least two opposing sides (2 vents total) at a minimum
size of 18 sq. inches of total free area each (Example: 3”x 6” or larger). Installation of the vents
in the mid to lower area of the enclosure is recommended. Ventilation allows for heat and or
residual fuel to escape. Failure to properly vent enclosure may result in the fire-pit overheating or
explosion. Some enclosures may require more ventilation based on material, size, and extended
use. The vent may work as a drain as well when installed at bottom sidewall to prevent water
build up.
 The interior void space of the enclosure surrounding the valve box cannot be filled with any
material (gravel, crushed rock, concrete, etc.)- It is a requirement to have a minimum of 2” under
the valve box for proper ventilation and drainage.
 Select materials that are non-combustible in both initial installations as well as over time.
 The fire pit assembly should be recessed a minimum of 2.25” from the top of the enclosure to
protect flame from being blown out. Some areas may require more- 4 to 6” is not uncommon.
WARRANTY REQUIREMENT:
 The enclosure must be constructed on a stable surface. The weight of the fire pit must be
supported by the pan and not by any control/valve box. For Electronic Ignition Component models
the control/valve box must be above grade with adequate drainage to prevent water damage to
the controls inside the box.
IMPORTANT:
 Make sure that the structure is level. We recommend the use of the installation collar (optional)
that may be mortared into the surround.
 The Outdoor Plus recommends that the pan lip is recessed on trough (linear). The Outdoor Plus
cannot guarantee the lip on all of our products will be perfectly flat and will not warp due to heat.
 Product must be accessible for service.
PROPER VENTING
 Certain fire pit enclosures may require extra ventilation depending on size, material or extended
use.
 1 Square Inch of ventilation is REQUIRED for every 25,000 BTUs.
 This is especially important for propane units, as propane gas is heavier than air and can pool in
the bottom of an enclosure.
WARNING: Venting is required to dissipate heat and any residual fuel. Failure to
provide proper ventilation could result in overheating and or explosion.

11
EXPERT TECHNICAL SUPPORT | MADE IN THE U.S.A. | 701 S. DUPONT AVE. ONTARIO, CA 91761 U.S.A.
SECTION 7
PRE-PLANNING CHECKLIST
THIS SECTION DEMONSTRATES THE PROPER INSTALLATION AND TESTING OF THE
Plug & Play to Low Voltage Pans & Burners.
SECTION 7  PREPLANNING CHECKLIST
TO ENSURE PROPER INSTALLATION PLEASE USE THIS PRE-PLANNING CHECKLIST:
 Recommended Tools:
 General Plumbing Tools (Pipe Wrench, Crescent Wrench, Pipe Cutters, etc.)
 Manometer (To test static & dynamic gas pressure)
 Voltmeter (To check voltage & amperage to unit)
 Gloves
 Mini-Butane Torch
 Cordless Drill
 Dielectric Grease or Silicone (For waterproofing wire nuts)
 Whistle-free Stainless Steel Flex Gas Hoses (TOP does not recommend using the
standard yellow corrugated flex gas hoses as those cause a loud persistent whistle
sound to occur when using the fire feature)
 Ensure the location is free of combustibles (See section 11 for more information.)
 Measure & record distances of gas piping & electrical conduit runs, these will be useful
for calculating gas pressure and proper wiring. The distance and wire gauge DIRECTLY
affects the performance of the Electronic Ignition Component.
 The Fire Feature is delivered on a pallet via freight and placed in front of your home.
Please have a team of movers ready to help move the unit from the curbside/driveway
to the desired location. ALWAYS inspect the pallet for damage or missing pieces, if there
is damage or missing pieces please DO NOT sign for the pallet and call our support team
immediately to help resolve any problems.
 All fire features require a hollow area underneath the pan for serviceability of the unit,
DO NOT FILL the hollow basin with sand or any other media.
 Gas Risers should come up to a maximum height of 2” from the ground and use a
90-degree fitting to help reduce the basin height and allow for easy servicing.
 TOP DOES NOT RECOMMEND to use the standard yellow corrugated gas flex hoses with
its fire features, TOP recommends to use a Whistle-Free Stainless Steel Gas Flex Hose
in order to help eliminate any whistling sounds.
 Ensure you use the Home-run method for connecting multiple Electronic Ignition
Component units, DO NOT DAISY CHAIN these units.
 Ensure you ordered the right gas type and ignition type for your installation.

12 THEOUTDOORPLUS.COM | [phone] | [e-mail]
SECTION 8
INSTALLATION INSTRUCTIONS
THIS SECTION DEMONSTRATES THE PROPER INSTALLATION AND TESTING OF THE PLUG & PLAY TO LOW VOLTAGE PANS & BURNERS
SECTION 8  INSTALLATION INSTRUCTIONS
STEP 1 | SELECTING A LOCATION
 Please see Section 5 on Selecting a location for instructions.
STEP 2 | VENTILATION & ENCLOSURE CONSTRUCTION
 Please see Sections 6 & 10 on ventilation & enclosure construction instructions.
 Ensure lava is not overfilled and do NOT cover the pilot for electronic electronic ignition valves.
STEP 3 | GAS CONNECTION
 Please see Section 3 for warnings.
 Place a ball valve close to the gas piping coming from the building for safety purposes.
 Gas Flow Pressure Requirements | See Figure 1
 Please reference figure 1 on the next page – We are looking for 7” (Natural Gas) or 11”
(Propane) Dynamic for optimum flow.
 Check dynamic & static gas flow pressure before the Electronic Valve Box.
 If the unit has a manifold please allow at least 10 inches of space in your design for a minimum
height basin for the manifold.
For appliances for use with a fixed fuel piping system and equipped with
an appliance gas pressure regulator, the appliance and its individual
shutoff valve must be disconnected from the gas supply piping system
during any pressure testing of the system at test pressures in excess of
½ psi (3.5kPa)
The appliance must be isolated from the gas supply piping system by closing its individual
manual shutoff valve(s) during any pressure testing of the gas supply piping system at
the pressures equal to or less that ½ psi (3.5 kPa)
STEP 4 | IGNITION OPTIONS
 There are numerous options available to turn on/off your fire feature, you may splice off the three-
prong plug and hard wire the provided unit to a UL certified light switch, pool controller, smart
home hub, wireless remote light switch, etc. Or simply use the provided three-prong plug to a UL
Certified outlet, smart outlet hub, GFCI, or extension cord.
 Please See Figure 3.1, 3.2, 3.3, & 3.4 for a visual reference on the ignition options.
STEP 5 | ELECTRICAL CONNECTION & TESTING
 Only a locally licensed electrician should install the electrical components. Please refer to your
local codes to ensure proper installation.
 Confirm that appropriate voltage and amps (minimum amperage required 2.0-2.2 amps)
 Use Waterproof Wire Nuts to ensure longevity & waterproofing of the wiring
 Use only UL/CSA/LC Certified components with the Plug & Play to Low Voltage Electronic
Ignition Electronic ignition valve.
STEP 6 | APPLYING FIRE MEDIA
 Please see Section 9 on Fire Media Usage
WARNING: TOP does NOT recommend you use fire glass/media on propane fire features, Liquid
Propane is heavier than Natural Gas and can pool up in the burn area and potentially cause
a backfire.

13
EXPERT TECHNICAL SUPPORT | MADE IN THE U.S.A. | 701 S. DUPONT AVE. ONTARIO, CA 91761 U.S.A.
SECTION 8
INSTALLATION INSTRUCTIONS CONT’D.
THIS SECTION DEMONSTRATES THE PROPER INSTALLATION AND TESTING OF THE PLUG & PLAY TO LOW VOLTAGE PANS & BURNERS
GAS PRESSURE REQUIREMENTS
Pressure Natural Gas Propane Gas
Minimum 3.5" W.C. / .87 kPa 8" W.C. / 1.99 kPa
Nominal 7" W.C. / 1.74 kPa 11" W.C. / 2.73 kPa
Maximum 14" W.C. / 3.48 kPa 14" W.C. / 3.48 kPa
Figure 1
HELPFUL TIPS FOR PROPER OPERATION
1. Cross ventilation is REQUIRED! A minimum of 1 square inch of ventilation is required for
every 25,000 BTUs on each side of the installation. Air flow is your friend!
2. Media (lava rock) minimum of 1/2” and no larger than 2” in diameter.
3. Media must not cover the pilot. The pilot needs air. Avoid packing media against the pilot.
4. Media must be approved by the appliance manufacturer.
5. A heat shield/Pan MUST be installed between the burner and Electronic Ignition Valve
6. The Electronic Ignition Valve has a temperature safety shutoff at 175° F.
7. Be sure the gas shut off valve is open.
8. If using wire nuts, be sure they are weather proof and use dielectric grease on the wires.
9. The unit is water resistant. NOT water proof! DO NOT PUT IN WATER OR SUBMERGE.
LED DIAGNOSTIC CODES
STEP 7 | OPERATION INSTRUCTIONS
Please see Section 11 on Operation Instructions, this section outlines how to operate your Plug &
Play to Low Voltage Pans & Burners fire feature.

14 THEOUTDOORPLUS.COM | [phone] | [e-mail]
SECTION 8
INSTALLATION INSTRUCTIONS CONT’D.
THIS SECTION DEMONSTRATES THE PROPER INSTALLATION AND TESTING OF THE PLUG & PLAY TO LOW VOLTAGE PANS & BURNERS
Figure 3.1
Figure 3.2
Ball
Ball
WARNING: Failure to position the parts in accordance with these diagrams or failure to
use only parts specifically approved with this appliance may result in property damage
or personal injury.

15
EXPERT TECHNICAL SUPPORT | MADE IN THE U.S.A. | 701 S. DUPONT AVE. ONTARIO, CA 91761 U.S.A.
Figure 3.3
Figure 3.4
SECTION 8
INSTALLATION INSTRUCTIONS CONT’D.
THIS SECTION DEMONSTRATES THE PROPER INSTALLATION AND TESTING OF THE PLUG & PLAY TO LOW VOLTAGE PANS & BURNERS
Gas
Line
(Key Valve)
Burner Pan
Ignition
Control Box
Burner Pilot Burner Assembly
Coupling
Orifice
MINIMUM 5’ AWAY FROM
ANY BODY OF WATER
110V
110V
Emergency Stop
Button on 110VAC
Always Place First
S
T
O
P
E
M
E
R
G
E
N
C
Y
Dial Timer
110VAC
Using an Emergency Stop & Dial Timer
110V - IN 110V - IN
110V - OUT
110V - OUT
Gas
Line
(Key Valve)
Burner Pan
Ignition
Control Box
Burner Pilot Burner Assembly
Coupling
Orifice
MINIMUM 5’ AWAY FROM
ANY BODY OF WATER
110V Leads
110V
Using a Standard Light Switch
Standard Light
Switch - 110VAC
Outside of the Firepit
110V - IN
110V - OUT
You may also cut off the three-prong plug and hardwire the leads into any 110V
application you’d like. These Electronic Ignition Components are compatible with a
wide array of smart hubs and controllers.
Air Mixer for Propane
Is Recommended for
Propane Burners. See
Instructions included
with the appliance
Hot / 110V
Ground
Neutral
LEGEND
1 square inch
of ventilation
required for every
25,000 BTUs
Ball
Ball

16 THEOUTDOORPLUS.COM | [phone] | [e-mail]
Figure 3.3
SECTION 8
INSTALLATION INSTRUCTIONS CONT’D.
THIS SECTION DEMONSTRATES THE PROPER INSTALLATION AND TESTING OF THE PLUG & PLAY TO LOW VOLTAGE PANS & BURNERS
Air Mixer for Propane
Is Recommended for
Propane Burners. See
Instructions included
with the appliance
Hot / 110V
Ground
Neutral
LEGEND
1 square inch
of ventilation
required for every
25,000 BTUs
NOTE: Propane cylinder NOT included. Make sure to properly locate the gas hose
including locating the hose out of pathways where people may trip over it or in areas where
the hose may be subject to accidental damage.
If you are using a remote propane gas supply system please see the following two diagrams.
For internal storage the construction of the enclosure should comply with all ventilation and
non-combustible enclosure requirements. See page 12 for more details.
*Propane tank & LP enclosure are not supplied.
Please see SECTION 6 - Enclosure Construction
WARNING: Failure to position the parts in accordance with these diagrams or failure to
use only parts specifically approved with this appliance may result in property damage
or personal injury.
For Propane Installations (See below & continued on next page):
1. Cross ventilation is REQUIRED! A minimum of 1 square inch of ventilation is required for
every 25,000 BTUs on each side of the installation. Air flow is your friend!
2. Propane Tank must be placed in/on a propane tank retainer/non-tip base to ensure the
propane tank will not tip over.
3. NOTE: Propane cylinder NOT included. Make sure to properly locate the gas hose including
locating the hose out of pathways where people may trip over it or in areas where the
hose may be subject to accidental damage.

17
EXPERT TECHNICAL SUPPORT | MADE IN THE U.S.A. | 701 S. DUPONT AVE. ONTARIO, CA 91761 U.S.A.
Figure 3.3
SECTION 8
INSTALLATION INSTRUCTIONS CONT’D.
THIS SECTION DEMONSTRATES THE PROPER INSTALLATION AND TESTING OF THE PLUG & PLAY TO LOW VOLTAGE PANS & BURNERS
Air Mixer for Propane
Is Recommended for
Propane Burners. See
Instructions included
with the appliance
Hot / 110V
Ground
Neutral
LEGEND
1 square inch
of ventilation
required for every
25,000 BTUs
NOTE: Propane cylinder NOT included. Make sure to properly locate the gas hose
including locating the hose out of pathways where people may trip over it or in areas where
the hose may be subject to accidental damage.
If you are using a remote propane gas supply system please see the following two diagrams.
For internal storage the construction of the enclosure should comply with all ventilation and
non-combustible enclosure requirements. See page 12 for more details.
*Propane tank & LP enclosure are not supplied.
Please see SECTION 6 - Enclosure Construction

18 THEOUTDOORPLUS.COM | [phone] | [e-mail]
SECTION 9
FIRE MEDIA USAGE
THIS SECTION DEMONSTRATES HOW FIRE MEDIA SHOULD BE INSTALLED & WARNINGS
SECTION 9  FIRE MEDIA USAGE
»DO NOT USE FIRE GLASS
»DO NOT USE: Stones of man made materials
»DO NOT USE: SAND, DO NOT FILL HOLLOW AREAS.
»DO NOT USE ANY FIRE MEDIA FOR PROPANE APPLICATIONS
Media used in the fire feature enhances the look of the flame and improves the fire pit
performance. As gas is emitted from the burner, the media helps mix air with fuel resulting in
a more uniform flame and a cleaner burn. The media will also help spread the flame across
all areas of the burner resulting in faster and more even ignition.
The media covering the burner should never exceed 2”. With all media, the pilot burner MUST
be left open to the air for proper ignition. When the media is placed correctly, you should
see the top of the pilot burner shield. If ignition is delayed or inconsistent, you may need
to remove some media from the pilot burner area. When using propane gas it is important
to check for back pressure created by excessive use of media that could result in gas being
forced back through the air mixer.
WARNING: Do not use any other material as media in the fire feature other than: Lava
rock no smaller than 1/2” average diameter.
WARNING: If the information in this manual is not followed exactly, a fire or explosion
may result causing property damage, personal injury, or loss of life.
WARNING: Placement of media (lava, stone, etc.) MUST NOT cover the
pilot assembly. DO NOT USE SAND OR SMALL MEDIA!
DO NOT COVER PILOTS WITH SAND!
USE ONLY PROVIDED MEDIA

19
EXPERT TECHNICAL SUPPORT | MADE IN THE U.S.A. | 701 S. DUPONT AVE. ONTARIO, CA 91761 U.S.A.
SECTION 9
FIRE MEDIA USAGE
THIS SECTION DEMONSTRATES HOW FIRE MEDIA SHOULD BE INSTALLED & WARNINGS
MUST READ! BURNING MEDIA INSTALLATION
👎
👍CORRECT INSTALLATION
ONLY FIRERATED MEDIA
PAN TO HOLD MEDIA
PROPER VENTING & CAVITY
WRONG INSTALLATION
NO PAN TO HOLD MEDIA
IMPROPER VENTING
COVERS PILOT IGNITER

20
SECTION 10
PARTS LIST
THIS SECTION OUTLINES THE LIST OF REPLACEABLE PARTS
SECTION 10  PARTS LIST
Ball Valve