THEMIX SHOP Ovana 019G User manual

2
Ovana
30 Ledgar Rd, Balcatta WA 6021
Appliance Name Ovana
Model/Type No. 019G
Brand TheMix Shop
Input rating 10.8 MJ/h
Injector size 0.95 mm
Gas Type Propane
Gas Pressure 2.75kPa
Use outdoors only. Read the instructions before using the appliance.
WARNING: accessible parts may be very hot. Keep young children
away. Do not use spirit or petrol for lighting or re-lighting.
HOT
SURFACE

3
12
GAS PIZZA OVEN
019G
Installation Manual
Number
Name
Qty
1
Chimney cap
1
2
Chimney
1
3
Oven body
1
4
Door
1
5
Handle
1
6
Knob for ignition and fire adjustment
1
7
Inlet interface
1
8
Pizza slate
1
A
Screw
2
Number Name Qty
1 Chimney Cap 1
2 Stove Pipe 1
3 Oven Body 1
4 Door 1
5 Handle 1
6 Control Knob 1
7 Gas Inlet 1
8 Baking Stone 1
9 Arch 1
10 Oven Feet 4
Number Name Qty
A Screw 2
B Screw Driver 0

4
78
Installation steps:
1. Screw the wooden handle onto the oven door with screw
2. Tighten four oven feet clockwise into the screw holes in four corners at the
bottom of the oven
3. Insert three fixed male tabs of the chimney into the chimney base, and
then tighten them clockwise
4. Harness the chimney cap sleeve into the stovepipe. The vertical plane of
the cap is the frontage
78
Installation steps:
1. Screw the wooden handle onto the oven door with screw
2. Tighten four oven feet clockwise into the screw holes in four corners at the
bottom of the oven
3. Insert three fixed male tabs of the chimney into the chimney base, and
then tighten them clockwise
4. Harness the chimney cap sleeve into the stovepipe. The vertical plane of
the cap is the frontage
78
Installation steps:
1. Screw the wooden handle onto the oven door with screw
2. Tighten four oven feet clockwise into the screw holes in four corners at the
bottom of the oven
3. Insert three fixed male tabs of the chimney into the chimney base, and
then tighten them clockwise
4. Harness the chimney cap sleeve into the stovepipe. The vertical plane of
the cap is the frontage
78
Installation steps:
1. Screw the wooden handle onto the oven door with screw
2. Tighten four oven feet clockwise into the screw holes in four corners at the
bottom of the oven
3. Insert three fixed male tabs of the chimney into the chimney base, and
then tighten them clockwise
4. Harness the chimney cap sleeve into the stovepipe. The vertical plane of
the cap is the frontage

5
910
5. Take out the pizza slate and clean up the packing stuff in the oven, and
then put the barbecue slate into the oven gently
6. Connect and tighten the air supply hose to the oven inlet port (refer to the
specification for the detail)
7. And then check whether the air leakage happens to the air supply system,
and start the ignition and preheat the barbecue slate if confirming there is no
potential safety hazard
Note: Carry out installation after wearing the work gloves to prevent the hand
scratch incurred by the metal edge or bend in the installation process
910
5. Take out the pizza slate and clean up the packing stuff in the oven, and
then put the barbecue slate into the oven gently
6. Connect and tighten the air supply hose to the oven inlet port (refer to the
specification for the detail)
7. And then check whether the air leakage happens to the air supply system,
and start the ignition and preheat the barbecue slate if confirming there is no
potential safety hazard
Note: Carry out installation after wearing the work gloves to prevent the hand
scratch incurred by the metal edge or bend in the installation process

6

7

8

9

10

11

12

13
Problem Cause Solution
Weak flame • Empty/low gas cylinder.
• High altitude.
• Cold gas cylinder.
• Try a dierent gas cylinder.
• Check gas regulator.
Noisy burner • Debris blocked head.
• Debris in oven.
• Clean oven debris with a so brush.
Slow heat up • Empty gas cylinder.
• Cold weather.
• Windy conditions.
• Try a dierent gas cylinder.
• Check gas regulator.
• Sheltered location.

14

15

16

17

18

19