Thompson roc 4306 User manual

The ROC 4306 is a universal remote control (4 in 1). It can replace 4 remote controls thanks to its
4 mode keys TV, VCR/DVD... It is compatible with the majority of television sets, video cassette
recorders, DVD players, satellite and cable receivers as well as terrestrial digital television (DVBT),
amplifiers and other audio equipment provided they are controlled by infra red signals.
This remote control has been factory programmed to allow you to use it immediately with the
majority of Thomson Group devices.We therefore advise you to try it before beginning to program it.
If programming is necessary, follow one of the methods A, B, C, D or E that are given in this manual.
But first, install 2 batteries (AAA) in the remote control.
Keep these instructions and the separate list of codes in a safe place so that you can later reprogram
your remote control.
1 Indicator lamp: the red indicator lamp lights up when
any key is pressed.
2 B: On / Standby.
3 Remote control mode
Selects device to control TV, DVD,VCR,...
4 B(Play): play*.
5 F(FF): fast forward *.
6 L (STOP): stop playback*.
7 K(Pause): stops on an image*.
8 I(EXIT): teletext Off in TV mode.
SHIFT and EXIT: turns off the menu of the
selected product.
9 VOL-/VOL+ increases (+) or decreases (-) the
volume of the TV set.
SHIFT and VOL-/VOL+ also allows you to
navigate the menus horizontally.
10 S: programmes the remote control.
SHIFT: activates the secondary key features
(indications in blue).
11 Number keys 0 to 9: these keys have the same
functions as those of your original remote and are
also used to enter the codes for different products.
12 Press this key first before you type in the 2-digit
channel number (except for Thomson group
products).
13 AV: for selecting an external source (SCART).
14 c: switches the TV sound off.
SHIFT and OK: confirms a selection.
15 PROG+,PROG-: programmes zapping button
(received by the television set or the satellite
receiver); use to scroll vertically through menus
SHIFT and PROG+/PROG- also allow you to
navigate the menus vertically.
16 a(MENU): teletext On/Off in TV mode.
SHIFT and MENU: turns on the menu of the
selected products.
17 M (RECORD): to record.
18 G(REW): goes backward or advances forward*.
* The coloured buttons can be used to select categories
when teletext is activated, and specific functions
depending on the make.
2 - Testing the remote control
before programming
1
1. Turn on the device that you wish to control.
2. Press the key corresponding (3) to the type of device
to control:
TV: television set,
VCR/DVD: video cassette recorder, DVD player,
DVB-T: DVBT receiver,
SAT: satellite.
3. Point the remote control at the device you wish to
control and try to turn it off using theB(2) key.
If the device does not turn off, you must program the
remote control using one of the methods A,B, Cor
Das described below.
1 - Description of keys 3 - Programming
the remote control
Before you start programming, you must find the subcode of
the set to be controlled.
Refer to the list provided with these instructions, page I of the
codes.
1 Switch on the set you want to control.
2. Hold down the S(10) key until the red indicator
lamp (1) remains lit (the indicator light remains on
for a few seconds to give you the time to proceed with
the following steps. The indicator lamp flashes when
this time is almost up, and then goes off).
3. Press the key (3) that corresponds to the type of
equipment you want to control:
TV: television set,
VCR/DVD: video cassette recorder, DVD player,
DVB-T: DVBT receiver,
SAT: satellite.
4. While the indicator is lit, type in the subcode (example:
1 for Thomson).
5. Direct the remote control towards the set and try to
switch it off by pressing the B(2) key.
6. If the set you want to control switches off, press
c(14) to memorise the subcode.
7. If the product doesn’t turn off, press the B(2) key
repeatedly until the set switches off.Wait approximately
one second between key presses to give the red
indicator lamp (1) enough time to go off and
light up again. This will allow you to see whether the
product responds or not.
8. Immediately upon the switching-off of the set to be
controlled, press c(14) to store the subcode.
Note:
If you want to assign another type of product than those
mentioned on the remote control (with the exception of the
TV button which can only be used to control a television set),
begin by entering the code that corresponds to the product you
want to programme (a 4-digit code that you will find in the code
booklet – see method B).
Example: if you want to control a satellite receiver with the
VCR/DVD key, begin by entering a satellite code (any satellite,
for example: 0603 for a Thomson satellite receiver) then begin
the procedure.
Check of the programming:
In principle, your set is ready for receiving the remote control
commands. Check your remote control for proper functioning by
performing the test described on page 3.
Method A – Fast programming with
1-digit subcode
1
GB
1
01_ROC4306_GB.indd 1 8/12/06 9:50:20

2
Method B – 4-digit codes Programming
Before you start programming, you must find the code of
the set to be controlled.
Refer to the list provided with these instructions, page II
of the codes.
1. Switch on the set you want to control.
2. Hold down the S(10) until the red indicator
lamp (1) remains lit (the indicator light remains on
for a few seconds to give you the time to proceed with
the following steps. The indicator lamp flashes when
this time is almost up, and then goes off).
3. Press the key (3) that corresponds to the type of
equipment you want to control:
TV: television set,
VCR/DVD: video cassette recorder, DVD player,
DVB-T: DVBT receiver,
SAT: satellite.
4. While the indicator is lit, enter the first digit of the
4-digit code proposed for the set to be controlled
(example: 0036 for Thomson). The red indicator then
goes off if the code is correct or flashes, if the code is
not on the list.
5. Direct the remote control towards the set and try to
switch it off by pressing the B(2) key.
6. Should the set not switch off, repeat step 2.Then type
in the next 4-digit code. Try to switch off the set by
pressing B(2) key once. Repeat this procedure by
trying out each of the 4-digit codes.
Check of the programming:
In principle, your set is ready for receiving the remote control
commands.Check your remote control for proper functioning by
performing the test described on page 3.
Method C – Programming by means of
code retriever
Should none of the codes work, you still have the possibility
of retrieving the appropriate code without having to perform
any input.
1. Switch on the set you want to control.
2. Hold down the S(10) until the red indicator
lamp (1) remains lit (the indicator light remains on
for a few seconds to give you the time to proceed with
the following steps. The indicator lamp flashes when
this time is almost up, and then goes off).
3. Press the key (3) that corresponds to the type of
equipment you want to control:
TV: television set,
VCR/DVD: video cassette recorder, DVD player,
DVB-T: DVBT receiver,
SAT: satellite.
4. Direct the remote control towards the set and try to
switch it off by pressing the B(2) key.
5. If the set you want to control switches off, press
c(14) to memorise the subcode.
6. Should the set not switch off, press B(2) key, as
many times as required (up to 200 times), until the set
switches off.Wait approximately one second between
key presses to give the red indicator lamp (1) enough
time to go off and light up again. Proceeding this way
will enable you to see whether the set responds or
not.
7. Immediately upon the switching-off of the set to be
controlled, press c(14) to store the subcode.
Note:
If you want to assign another type of product than those
mentioned on the remote control, begin by entering a code that
corresponds to the product you want to programme (a 4-digit
code that you will find in the code booklet – see method B).
Example: if you want to control a satellite receiver with the
VCR/DVD key, begin by entering a satellite code (any satellite,
for example: 0603 for a Thomson satellite receiver) then begin
the procedure.
Check of the programming:
In principle, your set is ready for receiving the remote control
commands.Check your remote control for proper functioning by
performing the test described on page 3.
Method D - Automatic code search
With this method, the remote control scrolls through the full
code list by sending an IR signal to the set to be controlled
remotely. Proceed as follows:
1. Check that your equipment is on. If not, switch it on
manually.
2. Hold down the S(10) until the red indicator
lamp (1) remains lit (the indicator light remains on
for a few seconds to give you the time to proceed with
the following steps. The indicator lamp flashes when
this time is almost up, and then goes off).
3. Release the S(10) key.
4. Press the key corresponding to the type of equipment
(for example TV).
5. Press the PROG+ (15) key once.After a few seconds
the remote control begins to list all the codes included
in the library (around 1 code per second). Press
PROG+ (15) a second time to reduce the speed
of the test (1 code every 3 seconds). As soon as the
device changes channel you must immediately press
c(14) to record the code and stop the listing. If
you have gone past the code, you can go back to the
previous code by pressing PROG- (15) as many
times as necessary (you can go forward by pressing
B(2) or PROG+ (15). As soon as the device reacts
again, press c(14) to record the code.
Note:
If you want to assign another type of product than those
mentioned on the remote control, begin by entering a code that
corresponds to the product you want to programme (a 4-digit
code that you will find in the code booklet – see method B).
Example: if you want to control a satellite receiver with the
VCR/DVD key, begin by entering a satellite code (any satellite,
for example: 0603 for a Thomson satellite receiver) then begin
the procedure.
Method E – Programming for control of a COMBO
(combined TV-VCR,TV/DVD,VCR/DVD, ... set)
Depending on the COMBO group (TV/VCR,VCR/DVD, etc.) and
the make, you will be required to enter a single code for both
devices in the COMBO, or to enter two codes, one code per
device. Consult the separate list to discover this. Before you start
programming, you must find the subcode or code of the
subset to be controlled (television or video recorder).
Refer to the list supplied with this user manual (see page
subcodes or codes).
GB
2
01_ROC4306_GB.indd 2 8/12/06 9:50:21

3
3
1. Switch on the COMBO you want to control.
2. Hold down the S(10) until the red indicator
lamp (1) remains lit (the indicator light remains on
for a few seconds to give you the time to proceed with
the following steps. The indicator lamp flashes when
this time is almost up, and then goes off).
3. Press the TV (3) key, then follow one of the
programming methods (A, B, C or D) described
earlier.
4. If a second code programming is required, then repeat
steps 2 and 3 above.
4 - How to retrieve
a programmed code
It may be useful to retrieve the code programmed in the
remote control.
1. Hold down the S(10) until the red indicator lamp
(1) remains lit (the indicator light remains on for a
few seconds to give you the time to proceed with the
following steps. The indicator lamp flashes when this
time is almost up, and then goes off).
2. Press the key (3) that corresponds to the type of
equipment you want to control:
TV: television set,
VCR/DVD: video cassette recorder, DVD player,
DVB-T: DVBT receiver,
SAT: satellite.
3. Press S(10) again briefly. The red indicator lamp
(1) flashes once.
4. Press the number keys (0to 9) in ascending order
until the red indicator lamp (1) flashes once.
5. The digit which made the red indicator lamp (1) flash,
is the first number of the 4-digit code. Please make
note of it.
6. Repeat step 4 to find out the other numbers of the
code.
7. When the fourth number is found, the red indicator
lamp (1) goes off.
5 - Check of the programming
- For a television or a satellite receiver: switch on and, for
example, press (15) to change channels.
- DVD player: load a DVD and then press PLAY (6).
Try other remote control keys to find out the range of
functions you can control. If you think that not all of the
keys are active, try the programming Method B or C.
When you have retrieved the code of your set, jot
it down so that you can use it whenever needed.
After battery replacement, you may have to
programme the remote control again.
7 - The NAVILIGHT system
The THOMSON NAVILIGHT navigation system allows you
easy access to the settings of your television set (TV) or your
video recorder (VCR) fitted with the THOMSON NAVILIGHT
system provided that you have allocated the VCR/DVD or
SAT keys to the video recorder.
1. Switch on the set you want to control.
2. Press the key corresponding to the type of set you
want to use (TV, VCR/DVD, or SAT). In the
VCR/DVD position, make sure that the AV mode is
activated for the TV set (the SCART socket must be
selected).
3. Press the S(10) key once and then press the a(16)
key.
4. Navigate through the setting menus with the play keys
p, q, tand u(9and 15).
5. Validate with OK (14).
6. To leave the menus, press key EXIT (8) once.
Note:The S(10) key remains on as long as light Iis lit. If this
light goes out, you have to press the S(10) key again before
using the navigation keys. To exit this mode, press S(10) a
second time.
ROC 4306 / EN / aws - rst / 12-2006
3
GB
6 - Other functions
Adjustment of ALL volume controls under a
specific mode.
You can allocate the volume control to one of the modes
of the remote control on condition that the volume
control exists on the corresponding device (e.g. control of
TV sound in VCR/TV mode).
1. Hold down the S(10) key until the red indicator
lamp (1) remains lit.
2. Release the S(10) key.
3. Press the c(14) key. The red indicator lamp (1)
flashes once.
4. Press once on the mode key (TV, VCR/DVD…)
corresponding to the device whose volume will always
be controlled by the VOL (9) and c(14) keys.
5. Press the c(14) key once.
Adjustment of the volume controls for EACH
mode.
You can decide that the volume control is functional for
each mode selected on condition that the volume control
exists on the corresponding device (e.g. control of the
television set sound in TV mode, the control of the sound
of the SAT receiver in SAT mode, ...).
1. Hold down the S(10) key until the red indicator
lamp (1) remains lit.
2. Release the S(10) key.
3. Press the c(14) key. The red indicator lamp (1)
flashes once.
4. Press once on the mode key (TV, VCR/DVD…)
corresponding to the device whose volume will always
be controlled by the VOL (9) and c(14) keys.
5. Press the VOL - (9) key once.
6. Press the c(14) key once.
You can contact THOMSON by dialling:
0871 500 0520
(call to this number
will be charged at 10 pence per minute)
www.thomsonlink.com
TV CODE VCR/DVD CODE
TVB-T CODE SAT CODE
01_ROC4306_GB.indd 3 8/12/06 9:50:22