THOMSON CALI-B 520010 User manual
www.mythomson.com
V1
EN Smart WiFi thermostat
For boilers
520010
CALI-B
24V
Solaire
OPTION
4m / 200kg Batterie
de secours
OPTION
GarantieGarantie
ans
Google Play
Free available on
Available on the
Google Play
Free available on
Available on the
EN 2
SMART WIFI THERMOSTAT
TABLE OF CONTENTS
A. SAFETY INSTRUCTIONS 5
1. OPERATING PRECAUTIONS 5
2. WARNING 5
2. MAINTENANCE AND CLEANING 5
3. RECYCLING 5
B. PRODUCT DESCRIPTION 6
1. KIT CONTENTS 6
2. DESCRIPTION 6
3. CHARACTERISTICS 7
C. INSTALLATION 8
1. TEMPERATURE SENSOR CONNECTION 8
2. INSTALLING THE HEATING MODULE 8
3. CONNECTION AND USE FROM THE MOBILE APP 8
3.1. INSTALLING THE APP AND PAIRING THE PRODUCT. 9
3.2. PAIRING THE TEMPERATURE SENSOR 9
3.3. PAIRING YOUR BOILER MODULE 11
3.4. ADDING THE THERMOSTAT 12
3ENEN
3
D. USING THE PRODUCT 14
1. TEMPERATURE SENSOR 14
2. THERMOSTAT (OPTIONAL WITH A HEATING MODULE) 14
2.1. SETTINGS. 14
2.2. PROGRAMMING 14
2.3. VOICE ASSISTANT COMPATIBILITY 15
3. CONSUMPTION MONITORING 15
E. TECHNICAL AND LEGAL INFORMATION 16
1. TECHNICAL CHARACTERISTICS 16
2. WARRANTY 16
3. ASSISTANCE AND ADVICE 16
4. PRODUCT RETURNS - AFTER SALES SERVICE 16
5. DECLARATION OF CONFORMITY 17
5EN
SMART WIFI THERMOSTAT
A - SAFETY INSTRUCTIONS
1 - OPERATING PRECAUTIONS
• Read this entire manual before installing.
• Do not allow children to operate the product.
• Do not install this product outside
2 - WARNING
This product was designed to measure temperature
and control electric or boiler heating when paired
with the Cali-ON or Cali-P modules. Any other
use of the device is not covered by the warranty
or technical support. The company cannot be
held liable for any use that does not comply with
the instructions in this manual and which causes
damage. Children should be supervised to make
sure that they do not play with the device.
2 - MAINTENANCE AND CLEANING
• The outer case can be cleaned periodically.
• Disconnect from the mains before carrying out
any work on the device.
• Do not use abrasive substances, substances
containing alcohol, thinners or other ammable
substances.
• Do not spray any products directly onto the
unit.
3 - RECYCLING
This logo denotes that devices no
longer in use should not be disposed of
as household waste. They are likely to
contain hazardous substances that are
dangerous to both health and the
environment. Return the equipment to
your local distributor or use the recycling collection
service provided by your local council.
Pour en savoir plus :
www.quefairedemesdechets.fr
6
SMART WIFI THERMOSTAT
EN
B - PRODUCT DESCRIPTION
The Thomson Cali-B thermostat lets you control your home’s temperature from your smartphone (Apple and
Android). It has an LCD screen.
Easy to install and use, it will quickly t into your lifestyle. You can congure weekly programmes from the app.
Easy to install and use, it will quickly t into your lifestyle.
1 - KIT CONTENTS
2 - DESCRIPTION
3x 2
1x 1 2x 2
1Control module for boilers
2Wall plugs for attaching the module to the wall
3screws for attaching the module to the wall
1Power indicator light
2Pairing button
3Front plastic cover for accessing the
mounting holes
4Back plastic cover for accessing the
connection terminal block
4Temperature sensor
5USB-MicroUSB cable
6USB charger
1
2
3
4
1+ button
2LCD screen
3- button
4RESET button
5MicroUSB port
3 5 5421
6x 1
4x 1 5x 1
7EN
SMART WIFI THERMOSTAT
B - PRODUCT DESCRIPTION
3 - CHARACTERISTICS
1. Temperature sensor
- Unit and temperature range: °C or °F, from 0 to 38°C (from 32 to 100°F)
- Humidity measurement range: from 20% to 90%
- Buttons on the front panel: Changing the set point temperature
- Measurement frequency: Every 2 minutes
- Screen: LCD, useful size: 30 x 30 mm
- Use: Indoors only
- Operating temperature: 0°/+40°C
- Storage temperature: -20°C/+70°C
- Power supply: Micro USB cable with 5 V adapter (included)
- Installation: On stand (included)
- Colour: Sand/Pure white
- Protection rating: IP20
- Weight: 57 g
2. Cali-B control module for boilers
- Power supply: 230 V – 50 Hz
- Maximum power: 1150 W – 5 A
- Use: Indoors only
- Operating temperature: 0°/+40°C
- Storage temperature: -20°C/+70°C
- Installation: wall mounting
- Average consumption: < 1 W
- Protection rating: IP20
- Weight: 80 g
EN 8
SMART WIFI THERMOSTAT
Your temperature sensor and boiler module must be
within WiFi range of your router/gateway in order
to function. If it is installed outside WiFi range, you
should install a WiFi repeater to boost the signal.
1 - TEMPERATURE SENSOR CONNECTION
2 - INSTALLING THE HEATING MODULE
After disconnecting the electricity supply, install
the module near the boiler and connect it to the
electricity supply.
1B,1
/B,1
2&
2&
$9a
Connecting to a boiler
with thermostat input
N Input P Input OC1 OC2
blue
red
power supply
outlet
230V/50Hz
N Input
P Input
Boiler’s thermostat
control input
Once the electrical connection has been done,
replace the plastic cover at the back and attach
the receiver to the wall using the wall plugs and
screws included. The xings provided are suitable
only for masonry walls.
3- CONNECTION AND USE FROM THE
MOBILE APP
This product only works with a 2.4Ghz frequency.
During pairing, make sure your smartphone is
connected on that specic frequency. If you are not
sure, check with your Internet service provider.
C - INSTALLATION
9ENEN
SMART WIFI THERMOSTAT
3.1. Installing the app and pairing the product
Once the temperature sensor and heating module
are connected, follow the instructions below for
pairing.
Download the Thomson At Home app from the Play
Store or App store.
At Home
Launch the app and log in if you already have
an account. If you do not, press INSCRIPTION
(REGISTER) and follow the app guide
Once you have entered your email address and
password, you will receive a conrmation code
in your inbox. Enter this code to nalise the
registration. Note that you might nd this email in
your spam folder.
3.2. Paring the temperature sensor
To begin pairing, press the menu at the top left and
select AJOUTER UN PRODUIT (ADD A PRODUCT).
Ensure that your phone is connected to the 2.4 GHz
WiFi network of your ADSL router
Select the product you wish to pair and select the
CALI-TEMP temperature sensor.
10
SMART WIFI THERMOSTAT
EN
C - INSTALLATION
Make sure the temperature sensor is plugged in and
in pairing mode. In pairing mode, the temperature
sensor’s screen should be ashing. If this is not the
case, press and hold the “reset” button at the rear
of the temperature sensor for 3 seconds.
Next, press COMMENCER LA CONFIGURATION
(START SETUP).
Select your 2.4 GHz WiFi network (note: your
smartphone must be connected to the WiFi network
to which the module will be connected), enter your
network password and press SUIVANT (NEXT).
Please wait while the pairing procedure takes
place. This stage can last several minutes.
IMPORTANT: The network compatibility of this
device is 2.4 GHz WiFi - WPA/WPA2. Not compatible
with 5 GHz WiFi or with WEP encryption.
Please check the WiFi settings of your router
or contact your Internet service provider if you
experience connection difculties. In case of failure,
check the module’s Wi-Fi range. To do so, connect
it close to your Wi-Fi network. Check your network
password and check that you are on 2.4GHz WiFi.
Then perform a reset and restart the procedure.
Your Thomson temperature sensor has been paired
successfully. You can name it and press TERMINER
(FINISH).
Your temperature sensor is now operational and
appears in your dashboard. Wait until the icons
change from grey to black (indicating conrmation
of connection to your WiFi network). Your
temperature sensor is now ready to use.
11 EN
SMART WIFI THERMOSTAT
C - INSTALLATION
You can view the temperature and humidity level
from your smartphone.
3.3. Pairing your boiler module
To begin pairing, press the menu at the top left and
select AJOUTER UN PRODUIT (ADD A PRODUCT).
Ensure that your phone is connected to the 2.4 GHz
WiFi network of your ADSL router.
Select the product you wish to pair and select the
Cali-On module.
Make sure the Cali-B module is plugged in and
in pairing mode. In pairing mode, the heating
module’s indicator light blinks quickly. If it is not
blinking, press and hold the centre button for 10 s
to put the module in pairing mode.
Next, press COMMENCER LA CONFIGURATION
(START SETUP).
Select your 2.4 GHz WiFi network (note: your
smartphone must be connected to the WiFi network
to which the module will be connected), enter your
network password and press SUIVANT (NEXT).
EN 12
SMART WIFI THERMOSTAT
C - INSTALLATION
Please wait while the pairing procedure takes
place. This stage can last several minutes.
IMPORTANT: The network compatibility of this
device is 2.4 GHz WiFi - WPA/WPA2. Not compatible
with 5 GHz WiFi or with WEP encryption.
Please check the WiFi settings of your router
or contact your Internet service provider if you
experience connection difculties. In case of failure,
check the module’s Wi-Fi range. To do so, connect
it close to your Wi-Fi network. Check your network
password and check that you are on 2.4GHz WiFi.
Then perform a reset and restart the procedure.
Your Thomson Cali-On module has been successfully
paired. You can set a name and press TERMINER
(FINISH).
Your boiler module is now operational and appears
in your dashboard. Wait until the icons change from
grey to black (indicating conrmation of connection
to your WiFi network). You can now use your boiler
module and create a thermostat.
3.4. Adding the thermostat
Before adding a thermostat, you must have
connected a temperature sensor and one or more
heating modules
Press the menu at the top left and select AJOUTER
UN PRODUIT (ADD A PRODUCT).
13 ENEN
SMART WIFI THERMOSTAT
C - INSTALLATION
Select the product you wish to pair. Select Thermostat.
Make sure the temperature sensor and the heating
module(s) are plugged in
1. Select the temperature sensor you wish to use
2. Select the heating module(s) you wish to use
3. Select the home’s typical inertia
4. Name the thermostat
Press enregistrer (save) to nish saving your
thermostat.
Your thermostat is now operational and appears in
your dashboard. You can use your thermostat to set
the temperature in your room and program it for
added comfort and savings.
EN 14
SMART WIFI THERMOSTAT
D - USING THE PRODUCT
1 - THE TEMPERATURE SENSOR
You can view the temperature and humidity level
from your smartphone.
You can check the temperature from your Google
Home and Alexa voice assistants:
- Ask how warm the room is
- Alexa/OK Google, what’s the temperature in
the living room?
2 - THERMOSTAT (OPTIONAL WITH A HEATING
MODULE)
Press the “Plus” (More) button for settings and
programming
2.1. Settings
• The temperature can also be changed for each
mode
• You can add/remove modules and change the
initial setup
2.2. Programming
• You can change the weekly programme, including
applying settings from another day to simplify
programming
• You can add/remove time slots for more exibility
15 ENEN
SMART WIFI THERMOSTAT
D - USING THE PRODUCT
You can directly override the programming using
the +/- buttons on the temperature sensor and
impose this setpoint temperature until the next
programmed time slot.
2.3. Voice assistant compatibility
Your new smart thermostat is compatible with both
Google Home and Alexa voice assistants. Refer to
your voice assistant’s instructions to connect your
thermostat.
Once connected, you can:
- Turn the thermostat on and off
- Alexa, turn on the thermostat
- OK Google, turn off the thermostat
- Ask the assistant to increase the temperature
- Alexa, increase the temperature by 1°C
- Ok Google, lower the temperature by 1°C
- Ask the assistant to set a temperature
- Alexa, set the temperature to 20°C
- OK Google, set the temperature to 20°C
3 - ELECTRICITY CONSUMPTION
MONITORING
You can monitor your heating’s electricity
consumption per day, month or year and
compare it from one year to the next. Perfect for
making energy savings.
16
SMART WIFI THERMOSTAT
EN
1 - TECHNICAL CHARACTERISTICS
TEMPERATURE SENSOR
• T° measurement unit and range: °C or °F, from 0 to
38°C (from 32 to 100 °F)
• Humidity measurement range: from 20% to 90%
• Buttons on the front panel: Changing the set
point temperature
• Low battery detection: Information displayed on
the sensor screen and transmitted by radio signal
• Measurement frequency: Every minute
• Screen:
- Overall size: 35 x 35 mm
- Useful size: 30 x 30 mm
- Segment screen
- Segment visualisation
• USB power supply:
Power supply of 5 V/100 mA
minimum
• Use: Indoors only
• Operating T°: 0°/+40°C
• Storage T°: -20°C/+70°C
• Installation: Ideally placed on a piece of furniture
in the middle of the room
• Colour: Black
• Protection rating: IP20
• Weight: 58 g
CALI-ON HEATING MODULE
• Radio frequency: 2.4GHz WiFi
• Power: maximum transmitting power 100 mW
• Radio range: up to 30m indoors. Up to 25m if
going through walls
• Power supply: 230VAC 50Hz
• Operating temperature: 0°C à 40°C,
indoor use only
• Maximum power: 1150W - 5A
• Connection: wired connection between the
module and
the device to be operated
• Cable section up to 2.5mm2
• Average consumption: < 1 W
• Protection rating: IP20
2 - WARRANTY
This product is guaranteed for parts and labour
for 2 years from the date of purchase. Proof of
purchase must be retained for the duration of the
warranty period.
The warranty does not cover damage caused by
knocks or accidents.
3 - HELP AND SUGGESTIONS
• If, despite the care we have taken in designing
our products and drafting these instructions, you
do encounter difculties when installing your
product or you have any questions, we urge you
to contact one of our specialists who will be glad
to help.
• If you encounter operating problems during
the installation or a few days afterwards,
it is essential that you are in front of your
installation when contacting us, so that one of
our technicians can diagnose the source of the
problem, as it will probably be the result of a
setting that is incorrect or an installation that is
not to specication. If the problem is caused by
the product itself, the technician will give you an
RMA number so that you can return the unit to
the shop.
Without this RMA number, the shop may refuse to
exchange your product.
Contact our after sales service team technicians:
0,35 €
/ min
0 892 701 369
Monday to Friday, 9pm to 12pm, and 2pm to 6pm.
Alternatively, talk to our chatbot free of charge:
https://www.avidsen.com/chatbot-thomson.html
4 - PRODUCT RETURNS - AFTER SALES
SERVICE
If, despite the care we have taken in designing and
manufacturing your product, it needs to be returned to
our customer service centre, you can check the progress
of the work on our website at the following address:
https://www.avidsen.com/nos-services
E - TECHNICAL AND LEGAL INFORMATION
17 EN
SMART WIFI THERMOSTAT
E - TECHNICAL AND LEGAL INFORMATION
5 - DECLARATION OF CONFORMITY
Avidsen declares that the above product complies
with the RED 2014/53/EU directive. Its compliance
has been assessed pursuant to the applicable
standards in force:
Temperature sensor
EN 62479
EN 62368
EN 301 489-1 V2.1.1
EN 301 489-3 V2.1.1
EN 300 220-1 V3.1.1
EN 300 220-2 V3.1.1
EN 300 328 V2.2.2
Mains adaptor
EN 62368
EN 55032
EN 55035
EN 61000-3-2
EN 61000-3-3
EN 50563
EN 50581
EN 62321
Cali-B module
EN 60335-1:2012 + A11:2014 + A13: 2017
EN 62311:2008
EN 301 489-1 V2.1.1
EN 301 489-17 V3.1.1
EN 300 328 V2.1.1
Tours, 23/03/2021
Alexandre Chaverot, CEO
Avidsen
19 avenue Marcel Dassault
ZAC des Deux Lions - 37200 Tours - France
Table of contents
Other THOMSON Thermostat manuals
