THOMSON B9 Series User manual

User Manual
B9 Series & UD9 Series

CONTENTS
Introduction 1
Warnings & Safety Precautions 1
Features 2
Safety Information 2
Important Safety Precautions 3
Prepration Stand Installation 4
Functional Overview Front & Side Panel 5
Functions 6
Connections 7
Remote Control 8-10
Basic Operation 11
Menu Operation 12-18
Media Play 19
Network Setting 20
Instructions for Intelligent Platform Operation 21-24
Troubleshooting 25-27

INTRODUCTION
Thank you for choosing our product. To be able to make use of all application options we
recommend that you should read this operation manual carefully and preserve it for quick
access, if required.
Do not touch any parts in the set and do not make changes to any settings not described in
this operating manual.
The LED Screen is a high-tech product which consists of more than 9,00,000 control
elements. Any Non-active red, blue or green spots lines that might appear on the screen
occasionally have no effect on the performance of the screen or television and may disappear
over a short period of time.
WARNINGS AND SAFETY PRECAUTIONS
Warning:
– To prevent damage to the TV which may result in a fire or electrical shock hazard, do not
expose the TV set to rain or excessive moisture.
– Do not rub or strike the Active matrix LED with any thing hard as this may scratch, mark or
damage the active matrix LED permanently.
– For safety, do not place vessels or any container which contains fluids including water, on or
near the TV.
– Do not insert any objects in the ventilation slots.
Service:
– Do not remove the back cover of the set as this can expose you to very high voltage and
other hazards. If the set does not operate properly, unplug it and call THOMSON HD LED
TV customer care.
Location:
– Position the set so that no bright light or sunlight falls directly on the screen. Reflections on
the screen affects the picture quality & viewing television.
– Soft and indirect lighting is recommended for comfortable viewing.
– Care should be taken not to expose the set to any unnecessary vibration, moisture, dust or
heat.
– Adequate ventilation is essential to prevent set failure.Ensure that the set is placed in a
position to allow a free flow of air. Do not cover ventilation opening on the back cover. Do
not place the set in an enclosure or very close to walls.
– Avoid excessively warm locations to prevent possible damages to the set.
– Place the television on a solid and flat surface, if not wall mounted.
1

FEATURES
SAFETY INFORMATION
2
– SMART LED TV
FHD / UHD 4K Resolution –
Extra Slim Design–
500000:1 Dynamic Contrast Ratio–
HDMI Connectivity–
Full Multimedia Interface–
Seven Picture Modes–
Five Sound Modes–
o o
178 x178 Viewing Angle–
PC Connectivity–
Dynamic Noise Reduction–
LAN & Wi-Fi Connection for Internet–
Web Browsing–
CAUTION
RISK OF ELECTRIC SHOCK
DO NOT OPEN
High voltages are used in the operation of
this product. To reduce the risk of electric
shock, do not remove cover of the cabinet,
refer for servicing to qualified service personal.
If the LED TV require any changes or coarse adjustment, electric shocks
are imminent. Do not attempt to open, contact customer support for
needed overhual.
The exclamation point within an equilateral triangle is
intended to alert the user to the presence of important
operating & maintenance (servicing) instruction in the
literature accompanying the appliance.
The lightning flash with arrowhead symbol within an
equilateral triangle, is intended to alert the user to the
presence of uninsulated dangerous voltage within the
products enclosure that may be of sufficient magnitude
to constitute a risk of electric shock to persons.
Warning

IMPORTANT SAFETY PRECAUTIONS
3
- Read & keep this instruction manual.
- Keep these instructions.
- Heed all warnings & follow all instructions.
- Do not use this apparatus near water.
- Clean only with dry cloth.
- Do not block any ventilation openings. Install in accordance with the manufacturer’s
instructions.
- Do not install near any heat source such as radiators, heat registers, stoves or other
apparatus (including amplifiers) that produce heat.
- If the provided plug does not fit into your outlet, protect the power cord from being walked
on or pinched particularly at plugs, socket outlets and the point where they exit from the
apparatus.
- Only use attachments / accessories specified by the manufacturer.
- Use with the bracket or table stand specified by the manufacturer or sold
with the apparatus.
- Unplug this apparatus during lightning storms or when unused for long periods of time.
- To reduce the risk of fire or electric shock, do not expose this apparatus to rain or moisture.
- The apparatus should be disconnected from the mains by placing the power / standby
switch in the standby position and unplugging the power cord of the apparatus from the
AC main outlet.
- The socket outlet should be installed near the equipment & should be easily accessible.
- This product should never be placed in a built-in installation such as a bookcase or rack
unless proper ventilation is provided or the manufacture’s instructions have been adhered to.
- The apparatus should not be exposed to dripping or splashing & objects filled with liquid,
such as vases, should be placed on the apparatus.
- Do not place any sources of danger on the apparatus (e.g. liquid filled objects, lighted
candles).
- Wall or ceiling mounting - The appliance should be mounted to a wall or ceiling only as
recommended by the manufacturer.
Servicing should be carried out by qualified service personnel only. To reduce the risk of
electric shock do not perform any servicing other than that contained in the operating
instructions.

PREPARATION
4
Stand Installation
The TV base will be separated with the TV unit. You should install the base before
you use the TV unit.
- Place the TV with its front side facing down on a cushioned flat surface.
- Place the base on the hinge of TV unit, with the base direction shown under
the base. (See the picture)
- Tighten the supplied screws to fix the TV stand securely in place.
(Screws - Provided with TV unit)
WARNING
- The TV stand may not be securely fixed in place after repeated tightening
and loosening of screws.
- During assembling and disassembling the TV stand, please use your hand
to support it. Failing to do so may cause the TV stand to fall and result in
personal injury / damage to the product.
- After installing the TV stand, please ensure that the screws are tightened
firmly. Failure to do so may cause the TV set to tip over or be damage.

FUNCTIONAL OVERVIEW
5
Front & Side Panel
1 Power Light
On Standby Mode, the light
turns red.
2 Infrared Remote Sensor
Receives the signals from the
remote control.
3 Power
Press to turn TV on or turn to
standby mode.
4 Menu
Press to display the setup menu on
the TV screen.
5 CH-, CH+
Press to select desired channels. or
press to select or adjust a menu item.
6 Vol-, Vol+
Press to adjust the volume level or Press
to select and adjust a menu item.
7 Input
Press to select source of viewing and
adjust all video input modes TV, AV,
HDMI, USB, YPbPr, VGA

FUNCTIONAL OVERVIEW
6
- LAN (Local Area Network)
For Internet connection
- USB
Insert USB
- HDMI input Terminal
Connect to equipment with HDMI output
- VGA(PC IN) Input Terminal
Connect to PC.
- PC / HDMI Analog Audio Input Terminal
Connect to equipment using HDMI-DVI
connection or PC with audio output.
- AV 1 & AV 2 In / YPBPR
Connect the video output jack of DVD or Set-top Box
- Antenna Input Terminal
Connect to equipment with antenna output or
wall antenna socket.
* Actual product specifications may differ from the above.

CONNECTIONS
7
You can connect DVD player, set-top box, computer, game console or other
equipment to the TV. To view external source images, press to select the input
source.
Source
Connecting an AV Equipment with HDMI Connector
Connecting an AV Equipment with Composite Connector
Connecting an AV Equipment with VGA Connector
- If the external equipment has DVI output, you can connect it to the HDMI terminal using a HDMI-DVI cable.
In case of using the HDMI-DVI cable, connect analog audio signal to RGB/HDMI analog audio input terminal.
- Please refer to the user manual of the external equipment for more information on connection to the TV.
- Please disconnect all power supplies to the equipment & TV before connection.
- Compatibility of the TV set and external equipment is dependent on hardware compatibility of both.

REMOTE CONTROL
8
Installing the remote control batteries
- Open the battery cover.
- Insert batteries (2x AAA size batteries)
Place batteries with their terminals observing
the (+) & (-) indications.
- Replace the cover & press down until the lock
snaps closed. If the remote control is not used
for an extended period of time, remove the
batteries from the remote control as damage
may result due to electrolyte leakage from the
batteries.
- The batteries shall not be exposed to excessive heat such as sunshine, fire or the like.
- Danger of explosion if battery is incorrectly replaced. Replace only with the same or
equivalent type.
- Risk of explosion if battery is replaced by an incorrect type. Dispose of batteries
according to the instructions.
- Do not dispose of batteries in a fire, danger of explosion.
- Batteries not covered under warranty.
- The remote may differ from the above picture.
Note:
POWER
FREEZE
SOUND MODE
PICTURE MODE
Settings / FAV -
FAV+/Capture
Turns TV into STANDBY ON/OFF.
Select to freeze the scene still on the screen.
Different sound features.
Different picture features.
Press to open internet set-up.
Press to switch your favorite channels under TV menu.
Press this key to capture video image
- Navigates vertically Up/Down through the Menu/Sub Menus.
- To enter character/numbers in program name parameter.
- To navigate channel Up/Down through valid channels.
- Navigates horizontally Right/Left through the Menu/Sub menus.
- To enter in Menu/Sub menus & to adjust Vol +/-.
- To navigate the letter in program name parameter.
- To select the time.
- To select Source by right arrow key.
- Increase / Decrease the value of selected items & set the
parameter On/Off.
- To enter in sub menu.
- Enter to edit program name parameter.
P
P
OK
EXIT Press to exit the OSD menu
FUNCTIONS

MENU
VOL +/-
ECO Vision
MUTE
SUBTITLE / COPY
ASPECT
GOTO
MEDIA / SPEAKER
To select menu OSD window and return to upper menu.
Change to cursor mode.
Select to increase or decrease volume.
This key provides the different power saving modes. The current mode is
displayed with ecovision symbol on the screen. In audio only mode display is off
& only audio is on. Press any key to exit audio only mode. Note: VOL+/-, PA+/- &
Mute can fuction even as panel is off. Note: Audio only mode is not available in
models 32” and above.
Turns sound OFF or ON
Figures 0-9 are used to directly input channel number.
Click to open internet browser.
- Press this key to display sub title list.
- Press this key to rename channels in program edit function.
- Press this key to copy / paste from USB to USB in USB Mode.
- Press this key to switch On/Off internal speaker used in TV set.
- Press this key to swap channel in program edit function.
- Press this key to open media center.
- Press this key to switch aspect ratio 16:9, 4:3, Zoom 1, Zoom 2, Auto scan
- Press this key to skip channel in program edit function.
- Press this key to STOP in USB mode
- Press this key to PLAY/PAUSE in USB mode
- Press this key to FAST REVERSE in USB MODE
- Press this key to FAST FORWARD in USB MODE
- Press this key to select play time position
When playing the Photo or Video or Mp3 or Text, if you select ROOT key it will stop
playing & return to the current list in USB mode.
Press to open home page.
- Press this key to play the previous track.
- Press this key to play the next track.
REMOTE CONTROL
9
Q. View
INPUT To select the source of viewing.
/ CH. LIST
PA +/- Select to increase or decrease volume for power audio
SLEEP / DELETE - To set sleep timer except when in program edit menu or USB mode.
- To select sleep timer except when you want seen next program after
selected time, you can enjoy watch TV set.
- Press this key to save channels when manual tuning or delete channel
when editing TV program in program edit function.

REMOTE CONTROL
10
Power On/Off
Turning on the TV
- Plug the TV’s power cord into a wall outlet (after this step, the main unit will turn on
and enter stanby mode automatically).
- Press the (Power) button on the TV, or press the (Power) button on the remote
control. The TV will turn on.
Placing In Standby Mode
Your TV can be placed in Standby mode in order to reduce the power consumption.
The standby mode can be usefull when you wish to interrupt viewing temporarily
(during a meal, for example).
- Press the Power Button.
- To switch back on, simply press power button.
Remark: Do not leave your TV in standby mode for long periods of time. (When you
are away on holiday, for example). It is the best to unplug the set from the mains and
aerial.
Changing Programmes
Using the programme selection buttons on the remote control to change
programmes
To select a programme, press the corresponding programme selection button
remote control. For example, to select programme 8, press the “8” programme
selection button on the remote control.
Using the P+/- buttons to sequentially change programmes
Press P+/- buttons on the remote control or on the TV to sequentially seletct
the TV programmes available in you area.
Using the button to return to sequentially change programmes
To return to the previous viewed programme, press the button on the remote
control.

BASIC OPERATION
11
Power On/Off
To turn on the TV
- Connect the power play into the wall outlet.
The power indicator lights in red, indicating
that the TV is in Standby Mode.
-Press
The Power indicator lights turns off & the
TV turns on.
To turn off the TV
-Press
The power indicator lights in red & the
TV turns off to standby mode.
- It takes approximately 10 sec. for the
picture to appear after the TV is turned on.
- The TV will switch to standby mode auto-
matically if there is no signal input for 10
minutes.
- If the TV will not be used for a long periods
of time, unplug the TV from the wall outlet.
Channel Selection
To select channel
Press P+/- or Program Select buttons to select
the channel number directly.
Input Source Selection
To select input “SOURCE”.
- Press to select the desired input source,
then press “enter” to enter. The selected
input source image displays.
INPUT Source : TV, AV-1, PC, HDMI , USB, YPbPr,
VGA
Volume Adjustment
To change the volume
- Press V+ to increase the sound volume level.
- Press V- to decrease the sound volume level.
To Mute the sound
- Press to temporarily turn off the sound.
- Press or V+ to restore the sound to
previous level.
- You can decrease the sound volume by pressing
V- while the sound is muted.
On-Screen Displays (OSD) Selection
& Adjustment
- Press “MENU” to display the main menu.
- Press to select a menu. The selected
menu page displays.
- Press to set your selection.
- Press to choose an item on the menu
page & press to set your selection.
- Press to adjust an item value or choose
options.
- Press “MENU” to return to the menu, press
”MENU” again to exit.
The OSD menu screen will be closed auto-
matically when no operation has been made
for the set OSD menu display time.

CHANNEL :
Auto Tunning : You can tuto tune all RF channels in ATV input source only.
ATV Manual Tunning : Channel
: Color System
: Sound System
: Search
: Frequency
CH1
Auto/PAL/NTSC/SECAM
BG/DK/I/M
< >
62.25 MHz
MENU
Program Edit
:
1 S-00 ATV
Delete Edit Move Skip
OGY B
Picture : Standard / Soft / User / Vivid/Natural/Sports/Lightness
ATV Manual Tunning Contrast
Brightness
Hue
Sharpness
Saturation
ECO
back Light
Color Temperature
Aspect Ratio
Image Noise
Reduction
: 0 - 100
: 0 - 100
: 0 - 100
: 0 - 100
: 0 - 100
: Off/Low/Middle/High
: 0 - 100
: Standard / Warm / Cool
: 16:9, 4:3, Zoom 1, Zoom 2
: Off/Weak/Middle/Strong
SOUND :
: 2016 / 7 / 1
: 09:02:40
: Setting off Time Off / On
Date
Current Time
Off Time
Standard / Music / Movie / News / User
Bass
Treble
Balance
AVC
Surround
SPDIF Output
Screen Off
: 0 - 100
: 0 - 100
: 0 - 100
: Off / On
: Off / On
: PCM/RAQ/OFF
: Music Only
(Press Ok, Only Sound, No Picture
To exit, press any key.
TIME :
: Setting Boot Time OFF/ON
On Time
Hour 9 (0-23)
Minute 05 (0-59)
(Off Time must be more, than 1 minutes after the current time)
Hour
Minute
Source
(Schedule time must behind the current time)
9
43
ATV
: Off / 10 min / 20 min/ 30 min/ 60 min / 90 mibn /
120 min / 180 min / 240 min.
Sleep Time
: Always / 5 Sec / 10 Sec / 15 Sec / 20 Sec / 30 Sec.
: Off / On
: Off / On
Stand by On : OFF / ON
ARC : OFF / On
Menu Time
Blue Screen
HDMI CEC
SETTING :
: 0 - 100
: >>>>
Menu Opacity
Restore To Default
MENU OPERATION
12

MENU OPERATION
Auto Tuning
ATV Manual Tuning
Program Edit
Channel Picture Sound Time Setting
Select Confirm Exit
13
Channel Setting (Use for TV)
- Press the “MENU” button on the remote
control to enter the OSD menu. Then
press buttons the “CHANNEL”.
- Press buttons to select the desired item,
then press or ENTER to enter.
- Press buttons on the remote control to
adjust desired item.
- Press the “MENU” button on the remote
control to return to upper menu.
At ATV input source, the first page showed is CHANNEL. At non ATV input source, the first page
is PICTURE as default. Currently press ENTER to get in sub menu, submenu highlight fixed on
press button key, the subtopic turns up with full screen.
Note : CHANNEL can be only selected under ATV condition, others can’t be used.
- Auto Scan : Enter Auto, it shows the process of frequency & the number of channels.
Press to select country & Tune Type at first,
press to select start or cancel, then press OK
button to start or exit Auto Scan.
- TV Manual Tuning:
Storage To : Current storage space shows, the following
option are available : 1-200.
System : Default option depends on country selection.
The following option are available : BG, I, DK
Current CH : Current channel shows.
Search : Can be searched at full channel condition.
Frequency : Show the current frequency & follow
search or Fine-Tune to adjust.
NOTE : After tuning by hand, make sure to press red button for storage, otherwise all channels searched
would not be stored after switching condition.

MENU OPERATION
14
- Program edit :
There are 3 items in the Preference page : Skip, Type
Select : Select your channel name by moving the cursor.
Delete : Delete current channel, as follows :
Press UP/DOWN buttons to choose the channel which you want to delete, then
press RED button to delete the current channel.
GREEN Button(Optional) :
Modify current channel name, only used in ATV mode.
- At normal condition, press GREEN button to enter RENAME mode.
- At RENAME Mode :
MENU : Press to exit RENAME mode, back to normal.
EXIT : Press to exit menu.
UP/DOWN : Press to switch letters, numbers or signs.
LEFT/RIGHT : Press to switch left & right, can select by circle.
GREEN : Press to exit RENAME mode, return normal condition.
Yellow Button (Optional) :
Channel switching function, ATV available as default.
- At normal condition, enter SWAP mode, & current selected channel is mobile channel X.
- At SWAP mode :
MENU : Press to exit SWAP mode, turn to normal condition.
EXIT : Press to exit menu.
UP/DOWN : Choose switch channels.
YELLOW : If current selected channel is what selected before X, no any other action,
Otherwise, the current channel is channel Y, need to exchange X& Y condition. But the
channel number stays 1,2,3,...... order as before.
BLUE Button (Optional) :
Choose if skip the channel when CH+/- channel tuning.
At Non Skip channel, press BLUE button, & Skip the current channel
At skip channel, press blue button to cancel skip.

MENU OPERATION
15
Picture Setting
You can adjust picture effects here, such as contrast,
brightness & etc.
- Press the “MENU” button on the remote
control to enter the OSD menu.
Then press buttons to select the “PICTURE”.
- Press button to select the desired item to enter.
- Press buttons on the remote control to adjust
desired item.
- Press the “MENU” button on the remote control
to return upper menu.
Picture Mode : Press buttons to select. The following option are available.
“Standard, Mild, User, Dynamic”
Contrast : Adjust image contrast.
Brightness : Adjust image brightness.
Color : Adjust the color saturation.
Sharpness : Adjust the sharpness level of image.
Tint : Determines the tint of the screen (This is only available with NTSC).
Color Temperature : Adjust the color temperature level of image. The following option are
available, “Normal, Warm, User, Cool”.
RED/GREEN/BLUE : Press buttons to adjust numeric size, Press MENU button to turn back
picture main menu.
Aspect Ratio : Press buttons to select, 16:9, Zoom 1, Zoom 2, Panorama, 4:3
Noise Reduction : Press buttons to select On/Off.
Color Temperature
You can select your favorite color temperature.
- Press the “MENU” button on the remote
control to enter the OSD menu. Then press
buttons to select the “PICTURE”
- Press button to select the “Color Temperature”
- Press buttons on the remote control to choose
color temp’s value.
- Press the “MENU” button on the remote
control to return to upper menu.
User : Adjust the color value.
Normal : Keep the original white color
Warm : Adjust the white color to a little bit red.
Cool : Adjust the white color to a little bit blue.
Remark : The changes you made will be stored automatically.

MENU OPERATION
16
PC Setting (Only for PC Mode)
The function only used in PC port to adjust PC position. Enter
the screen page with buttons or ENTER button.
- When input PC source, you can go to PC to set up menu.
- Press the “MENU” button on the remote control to enter
the OSD menu. Then press buttons to select the
“PICTURE SETUP” in main menu.
- You can press ENTER buttons to enter PC setup mode
after selecting PC setting , & the press buttons to
select your desired item press buttons to adjust.
- Press the “MENU” button on the remote control to
return to upper menu.
- In PC function operation will instruct more clear.
Sound Setting
You can customize different sound mode to get best effect.
- Press the “MENU” button on the remote
control to enter the OSD menu. Then press
buttons to select the “SOUND”
- Press button to select the desired item
to enter.
- Press buttons on the remote control to
increase or decrease the value of desired
item.
- Press the “MENU’ button on the remote
control to return to upper menu.
Auto Adjust : Press buttons, TV system adjust by itself, it can adjust, H position, V position, Phase & so
on that can make the image in center & display best.
H. Position : Adjust Horizontal Position of the PC Screen.
V. Position : Adjust the Vertical Position of the PC Screen.
Size : Adjust the size of the PC Screen.
Phase : When necessary, adjust the pixel phase of the picture to avoid picture interference.
Sound Mode : Press buttons to select one of the following options “Standard, Music, Movie,
Sports User”.
Treble : Adjust treble effect.
Bass : Adjust bass effect.
Balance : Adjust balance effect.
Auto Volume : (Auto volume control, when you turn on the TV, this feature allows the TV to
automatically adjust the sound output from level to the previous level of
last time when you turned off the TV) : On/Off.
Surround Sound : Select it to enter, then you can select Off or On.
SPDIF Output : Select it to enter, then you can select option PCM/RAW/OFF
For HD channel select only PCM
Music Only : Press OK (ENTER) only listen sound, no picture, to exit Press any key on remote control.

MENU OPERATION
Time
Clock
Off Time
On Time
Sleep Timer
Auto Sleep
09/NOV 04:19
13:57
13:58
Off
On
17
Time Setting
You can set the TV’s time & you should set time if you use the automatic On/Off times.
- Press the “MENU” button on the remote control to enter
the OSD menu.
Then press buttons to select the “TIME”.
- Press button to select the desired item to enter.
- Press buttons on the remote control to adjust desired item.
- Press the “MENU” button on the remote control to upper menu.
Sleep Timer : Press buttons to select your desired item (Off,
240 min., 180 min., 120 min., 90 min., 60 min., 30 min., & 10 min.)
Auto Sleep : Within 10 min. there is no signal, the TV will auto sleep
Clock
- Press the “MENU” button on the remote control to enter
the OSD menu.
Then press buttons to select the “TIME”.
- Press button to select CLOCK, then press ENTER button
to enter.
- Press buttons to select the desired item.
- Press the “MENU” button on the remote control to return upper
menu.
- Press the “MENU” button on the remote control to enter
the OSD menu.
Then press buttons to select the “TIME”.
- Press button to select Off Time, then press ENTER button to
enter.
- Press buttons to select the desired item, then press
buttons on the remote control to set the time.
- Press the “MENU” button on the remote control to return upper
menu.
Off Time