Titan Pro TPLS11TV User manual

Save This Manual for Future Reference
Original Instruction
FOR YOUR SAFETY
READ AND UNDERSTAND THE ENTIRE MANUAL BEFORE OPERATING
MACHINE
Both model number and serial number may be found on the main label.
You should record both of them in a safe place for future use.
Hydraulic Log Splitter
Operator's Manual
MODEL NUMBER: TPLS11TV
SERIAL NUMBER :

2
INTRODUCTION
ENVIRONMENTAL
SYMBOLS
TABLE OF CONTENTS
Introduction
Symbols
Safety
Contents Supplied
Assembly
Deliverying Log SplitterTo Work Site
Splitter Operation
Transport
Free a Jammed Log
Replacing Oil
Sharpening Wedge
Wiring Diagram
Parts Schematic
Trouble Shooting
Hydraulic System Diagram
Specifications
Safety Warnings & Instructions
2
2
3
3
5
6
7
9
9
8
11
11
12
13
14
13
13
Your new Titan Pro 11 ton log
splitter has been designed to more
than satisfy your expectations,
following in our long line of quality
garden machinery products. It has
been manufactured under
stringent quality standards in
order to offer a higher level of
performance. You will find your new
unit easy and safe to operate, and with
proper care, it will give you many years
of dependable service.
Carefully read through this
entire operator's manual
before using your new log
splitter. Take special care
to heed the cautions and
warnings.
Always recycle your
unwanted materials instead of
disposing of them as waste.
All tools, hoses and packaging
should be taken to your local
recycling center and
disposed of in an
environmentally safe way.
The rating plate on your
machine shows a number of
symbols. These represent important
information about the product, or
instructions on its use.
Read these
instructions in full
before using the
machine.
Wear appropriate footwear!
Wear protective gloves!
Wear eye protection!
Wear hearing protection!
Keep your work space
tidy! Untidiness may
result in accidents.
Do not remove or tamper
with any protection or
safety devices.
Dispose of the used oil in
an environmentally-friendly
way.
Do not use in the rain.
Danger! Keep clear of
moving parts!
Certificate of Conformity 17

3
SAFETY
Do not remove jammed logs
with your hands.
Caution! Thrown objects.
Before starting any repair
maintenance or cleaning,
always disconnect the power.
Avoid injury from the
movement of the
splitting blade.
Keep bystanders away from
the working area.
Do not split wood when
transporting your machine.
Do not split wood when
your machine is leaning.
Safety Warnings & Instructions
UNDERSTAND YOUR LOG SPLITTER
INSPECT YOUR LOG SPLITTER
DRESS PROPERLY
PROTECT YOUR EYES AND FACE
EXTENSION CORDS
DRUGS, ALCOHOL AND MEDICATION
AVOID DANGEROUS CONDITIONS
Read and understand the owner's
manual and labels affixed to the log
splitter. Learn its application and
limitations and take note of
the potential hazards caused by
misuse. Familiarise yourself with
the machine controls and their proper
operation.
Do not operate the log splitter while
under the influence of drugs, alcohol,
or any medication that could affect
your ability to use it properly.
Always operate your log splitter on dry,
solid, level ground. Never operate your
log splitter on slippery, wet, muddy, or icy
surfaces. The location you choose should
be free from any tall grass, brush, or other
interferences. There should be plenty of
room for operation. Keep your work
area tidy and well lit. Cluttered areas
can cause injuries. To avoid tripping, do
not leave tools, logs, or other
components laying around the work
area.
Check your log splitter before turning
it on. Keep guards in place and
in working order. Form a habit of
checking to see that keys and adjusting
wrenches are removed from tool area
before turning it on. Replace damaged,
missing or failed parts before using
it. Make sure all nuts, bolts, screws,
hydraulic fittings, hose clamps, etc. are
securely tightened. Always check the
oil level in the hydraulic oil tank. Never
operate your log splitter when it is in
need of repair or is in poor mechanical
condition. Before starting work, test
the stopping devices to keep them in
safe working condition.
Do not wear loose clothing, gloves,
neckties or jewelry (rings, wrist watches).
They can be caught in moving parts.
Protective electrically non-conductive
gloves, non-skid footwear and hearing
protection are recommended when
working. Wear protective hair covering
to contain long hair, preventing it from
get caught in machinery.
Any log splitter may throw foreign
objects into the eyes. This can cause
permanent eye damage. Always wear
safety goggles. Everyday eyeglasses
have only impact resistant lenses. They
are not safety glasses.
Improper use of extension cords may
cause inefficient operation of the log
splitter which can result in overheating. Be
sure the extension cord is no longer than
10m and its section is no less than 2.5mm2
to allow sufficient current flow to the
motor. Avoid use of free and inadequately
insulated connections. Connections must
be made with protected material suitable
for outdoor use.
Do not use the log splitter in wet or
damp areas,or expose it to rain. Do not
use it in areas where fumes from paint,
solvents or flammable liquids pose a
potential hazard.

4
AVOID ELECTRICAL SHOCK
PREVENT FIRES
DON'T OVERREACH
PROTECT YOUR HANDS
DON'T FORCE TOOL
DISCONNECT POWER
AVOID INJURY FROM UNEXPECTED ACCIDENT
INSPECT YOUR LOG
KEEP BYSTANDERS AWAY
Check that the electric circuit is
adequately protected and that it
corresponds with the power, voltage
and frequency of the motor. Check
that there is a ground connection.
Ground the log splitter. Prevent body
contact with grounded surfaces: pipes,
radiators, ranges, and refrigerator
enclosures. Never open the switch /
plug box. Should this be necessary,
contact a qualified electrician. Make
sure your fingers do not touch the
plug's metal prongs when plugging or
unplugging the log splitter.
Do not smoke or have open flames
when operating or refilling the log
splitter. Never operate the log splitter
near a flame or spark. Oil is flammable
and can cause explosions.
Keep proper footing and balance at
all times. Never stand on log splitter.
Serious injury could occur if the tool
is tipped or if contact is made
with the cutting tools. Do not store
anything above or near the log
splitter, to avoid encouraging anyone
to stand on the tool to reach them.
Keep your hands away from splits and
cracks which open in the log. They may
close suddenly and crush your hands.
Do not remove jammed logs with
your hands.
It will do a better and safer job at
its design rate. Don't use this log
splitter for any purpose for which
it was not intended. Do not alter
the equipment, or use the equipment
in such a way as to circumvent its
design capabilities and capacities.
Never try to split logs larger than
those indicated in the specifications
table.
Unplug when not in use, before making
adjustments, changing parts, cleaning,
or working on the log splitter. Consult
the technical manual before servicing.
Do not straddle or reach across the
splitting area when operating the log
splitter. Never pile logs to be split in
a manner that will cause you to reach
across the log splitter. Only use
your hands to operate the control
levers. Never use your foot, knee, a
rope, or any other extension
device. Always pay full attention to
the movement of the wedge ram.
Never attempt to load your log
splitter while the ram is in motion.
Keep hands out of the way of all
moving parts. Never try to split two
logs on top of each other, as this
may cause one to fly up and hit you.
Never attempt to split logs containing
nails, wire or other debris.
Always make sure that both ends
of the log you are splitting are cut
as square as possible. This will
prevent the log from sliding out
of position while under pressure.
Branches must be cut off, flush with
the trunk.
Allow only one person to load and
operate the log splitter. Always keep
bystanders, including visitors, children
and pets away from the work area,
especially when the log splitter is in
operation. Only the operator should
stand near the machine and only within
the safe operating area as
described in this manual. Never
use another person to help you
with freeing jammed logs. No one
under the age of 16 should be allowed
to operate the log splitter. Any
individual under the age of 18 should
have the necessary training and
skills to perform the functions
properly and safely, and should
always be under adult supervision.

5
PROTECT THE ENVIRONMENT
DEAL WITH ACCIDENT
OPERATION
MAKE THE WORKSHOP CHILDPROOF
MAINTAIN YOUR LOG SPLITTER WITH CARE
Take used oil to an authorised
collection point or follow the
stipulations in the country where the
log splitter is used. Do not discharge
into drains, soil or water.
Always have a fire extinguisher and
a first-aid kit available for use should
the need arise. In emergency always
know the location of the nearest
phone or keep a phone on the job site.
Also know the phone numbers of the
nearest ambulance, doctor and fire
department. This information will be
invaluable in the case of an emergency.
Lock your workshop. Store the log
splitter away from children and others
not qualified to use it.
Specifications
Model Number TPLS11TV
Log Size Capacity
Dia. 10-30 cm
Length 56~104 cm
Maximum Force 11 Ton ±10%
Hydraulic Pressure 25.2 Mpa
Hydraulic Oil Capacity 7.0 L
Ram Travel 85 cm
Speed
Forward 13.9 cm/s
2.9 cm/s
Retract 3.7 cm/s
Noise Pressure Level(LpA)≤80 db(A)
Vibration 2.5 m/s²
Overall Sizes
Length 144 cm
Width 133 cm
Height 228 cm
Weight 173.4 kg
* S6 40%, continuous operation periodic duty: time of one load cycle is 10 minutes, operation time at constant load is
4 minutes, operation time at no-load is 6 minutes.
Motor (S6 40%)* 230V~ 50Hz 3000W 13A
Before cleaning, repairing, inspecting
or adjusting, turn off and unplug your
machine, making sure all moving parts
have stopped. Always clean the unit after
each use. Keep the log splitter clean for
best and safest performance. Follow
instructions for lubricating. Inspect all
hydraulic seals, hoses and couplers for leaks
prior to use. Control levers and power
switch must be kept clean, dry and free
from oil and grease at all times.
This machine is designed to be
operated by one person only. Only
one person should operate the
machine and the ram head itself.
This machine must not be operated by
children.

6
1. Log Splitter Frame & Power Station
2. Guard Arm
3. Log Lift
4. Retaining Hook
1
2
3
4
6
9
5
7
8
5. Wheel
6. Wheel Axle
7. Support Wheel
8. Operator's Manual
9. Hardware Bag, including
CONTENTS SUPPLIED
Ø2x20 ×2 A
M10 ×30 ×1 B
M10 ×30 ×2 C
M16 ×90 ×1 D
APPLICATION CONDITIONS
This log splitter is designed for operation
under ambient temperatures between +5°C
and 40°C and for installation at altitudes no
more than 1000m above M.S.L. The
surrounding humidity should less than 50% at
40°C. It can be stored or transported under
ambient temperatures between -25°C and 55°
C.
ELECTRICAL REQUIREMENTS
With a 230 Volt / 50Hz motor, the log
splitter should be connected to standard
230V ± 10% /50Hz ± 1%.
Electrical supply which has protection devices
of under-voltage, over-voltage, over-current (16
A) as well as a residual current device (RCD)
which maximum residual current rated at 0.03A.
Electrical connection rubber cables must comply
with EN60245 which are always marked with
symbol H 07 RN. Cables should be identified, as
it is a legal requirement.
If machine installs BSI approved plug or SEV
approved plug, the degree of protection of the
plug and socket combination should be IP44 at
least.

7
ASSEMBLY
1. Insert the wheel axle into the holes
of the mount bracket. Slide the
wheels onto the axle and secure
with Ø2x20 split pins from outside.
Attach the wheel caps.
2. Keeping the support stand against
the wedge, remove the R-Pin and
bolt to release cylinder. Lower both
control handles to raise the wedge
ram to the top. Insert the bolt and
R-Pin to secure the cylinder.
2
3
4
1
Ø2x20 ×2 A
3. Release both control handles to
retract the wedge ram. Remove the
support stand.
4. Align the hole and locking pin of the
guard arm with the mount bracket.
Secure the guard arm with a M10 ×30
hex bolt, a washer and a nut from the
hardware bag.
M10 ×30 ×1 B

8
5. Position the retaining hook onto the
frame and secure with two M10×30
hex bolts and nuts.
6. Position the log lift inside the
mounting bracket and align with
the mounting bracket holes. Secure
with a M16×90 hex bolt and nut. Hook
the lift chain to the wedge slide guide.
M10 ×30 ×2 C
1
2
3
M16 ×90 ×1 D
The transporting handle is fixed upright
by the pin with clip for easier delivery.
Remove the clip and pin. lower the
handle in the direction of the arrow as
shown and secure it by fixing the pin
with clip to the outer hole.
Pull the spring pin and slide the square
tube of the support wheel into the
holder. Loosen the spring pin to fix it
after selecting the appropriate hole.
TRANSPORT
Upper Hole
Lower Hole
2
1
2
1
3
The upper hole is for transport,
and lower hole is only for
storage. Because the support
wheel is an universal wheel, it is
not stable enough for transport
if mounted at the lower hole!

9
MOVING THE LOG
SPLITTER TO THE
WORK SITE
The log splitter is equipped with 2
wheels for moving. To move the log
splitter, grip the handle (a) to tilt the
log splitter slightly after making sure
the oil tank cover is tightened.
Save difficulty and increase safety
in your work by having a plan
before beginning work. Have your
logs positioned where they can be
easily reached. Have your work site
located near your stack, the split
wood or load it onto a nearby
truck or other carrier. Position the log
splitter on solid level ground.
Applying a thin coat of grease to
the surfaces of the ram before
operation will help increase the
durability of the ram.
If a crane is used, tie the
rope at the lifting point
below the blue bundling
label, then hoist the
machine with the crane.
SPLITTER OPERATION
aBleed the air out of the hydraulic system
before starting the log splitter. The
cover of the hydraulic oil tank should be
loosened by some rotations until air can
go in and out of the oil tank smoothly.
Air flow through the oil tank filler should
be detectable during operation.
Before moving the log splitter, make
sure the cover of the oil tank is tightened
to avoid oil leaking from this point.
1. Place the log vertically
on the support table,
so that it lies flat on its
face. Press the left lever
to lower the extended
log fixing claw against
the log to secure it. The
extended log fixing claw
can be adjusted to fit
logs with different heights.
Splitting
Failure to loosen the oil tank
cover will keep the sealed air in
hydraulic system being
compressed and
decompressed. Continuous air
compression/decompression
will blow out the seals of the
hydraulic system and cause
permanent damage to the log
splitter.

10
2. Hold the left press lever.
Meanwhile, move the
splitter wedge down
by pressing the right
splitting lever to half
stroke to split the log
slowly,then press it to
the end until the log is
completely split.
3. Return the splitter
wedge to the starting
position. Operate the
spring-loaded retract
control lever to lift the
wedge above the height
of log to be split.
Idle Stroke
Slow
Fast
The spring is already connected
to the handle in factory.
Reverse Control
Handle
MANUAL
REVERSE

11
The splitting force and speed are
governed by the splitting lever.
The first half stroke of the splitting
lever is idle speed; press the splitting
lever to the half stroke for maximum
splitting force at slower speed to split
the log at the beginning or particularly
hard and seasoned logs;
Press the
splitting lever
to the end for
faster speed at
less splitting
force to finish
the splitting or
to split usual
logs.
It can be shifted by simply raising and
lowering the splitting lever slightly.
Splitting Lever
Stack as you work. This will provide
a safer work area, by keeping it
uncluttered, and avoid the danger of
tripping, or damaging the power cord.
Do not attempt to split green
logs. Dry, seasoned logs
split much more easily, and
will not jam as frequently as
green wood.
Do not remove jammed logs
with your hands. Never use
another people to help you
with freeing jammed log.
Break log in the direction
of its growing grain. Do
not place log across the
log splitter for splitting.
It may be dangerous and
may seriously damage the
machine.
Accumulated split wood
and wood chips can create a
hazardous work environment.
Never continue to work in a
cluttered work area which
may cause you to slip, trip or
fall.
Do not remove jammed logs with your
hands. If jammed, stop the motor and
loosen the log by a downward stroke
on the log with a hammer.
FREE A JAMMED LOG
REPLACING OIL
The hydraulic system is a closed
system with oil tank, oil pump and
control valve. Low oil levels can
damage the oil pump. Check the oil
level regularly with dipstick. The oil
should be completely changed once a
year.
Following hydraulic oils or equivalent
are recommend for the log splitter's
hydraulic transmission system:
Titan Pro ISO32 Hydraulic Oil
SHELL Tellus 22
MOBIL DTE 11
ARAL Vitam GF 22
BP Energol HLP-HM 22
Oil Filler Plug
Oil Drain Plug

12
SHARPENING WEDGE
Apply sealant to filler plug and reinstall
it.
Following an oil change, activate the
log splitter a few times without actually
splitting.
This log splitter is equipped
with a reinforced splitting wedge with
a specially treated blade. After
long periods of operation, and
when required, sharpen the
wedge using a fine-toothed file,
removing any burrs or flat spots on the
edge.
Read dipstick to determine
the maximum and minimum
oil level. Low oilcan
damage the oil pump.
Overfilling can result in
excessive temperature in
the hydraulic transmission
system.
Max.
Min. Oil level
Use a drain pan to aid in the removal of
all used oil and particles.
Remove the oil drain plug to drain oil
from the hydraulic transmission
system. Examine oil for metal
chips as aprecaution to future
problems.
After oil has been completely drained
from the machine, reinstall drain plug.
Add the recommended oil through
the filler plug opening.

13
TROUBLESHOOTING
PROBLEM PROBABLE CAUSE REMEDY SUGGESTED
Motor does not start Switch is OFF Turn the switch ON
Log splitter does not work
while the motor is running
Valve is not opening
owing to the connecting
parts being loose
Check and tighten the
parts
Control levers or
connection parts bent Repair the bent parts
Low hydraulic oil level Check and refill hydraulic
oil
Log splitter works with
abnormal vibration and
noise
Low hydraulic oil level Check and refill hydraulic
oil
ATTENTION: ALL REPAIR WORK MUST BE DONE BY A SPECIALIST
FOR THIS PRODUCT.
WIRING DIAGRAM HYDRAULIC SYSTEM
DIAGRAM

14
PARTS SCHEMATIC

15
Parts List
No. Description Q'ty
1 Left Guard Bracket 1
2 Bolt 8.8 M10x30 7
3
Flat Washer 10 9
4 Locating Pin Handle 2
5 Locknut M10 13
6 Lift Chain Φ61
7 Wedge Weldment 1
8 Bolt 8.8 M12x65 6
9 Friction Plate 4
10 Baffle Plate 2
11 Left Plate 1
12 Locknut M12 4
13 Large Washer 12 3
14 Cylindrical Pin 8x40 1
15 Control U-Handle 1
16 Right Plate 1
17 Nut M12 6
18 Axis Pin 1
19 Wheel Cap 12 2
20 Lift Guard 1
21 Cylinder 1
22 Spring 1
23 Nut M8 5
24 Bolt 8.8 M8x30 2
25 Bolt 8.8 M8x80 1
26 Oil Cap 1
27 O- Ring 25x2.65 1
28 Oil Dipstick 1
29 Nylon Washer 1
30 Shaft 1
31 Extended Log Fixing Claw 1
32 Nut M8 3
33 Log Fixing Claw 1
No. Description Q'ty
34 Locknut M8 4
35 Large Washer 8 6
36 Wing Bolt M8x25 1
37 Bolt M8x20 3
38 Lower Hose 1
39 Combined Washer 20 10
40 Upper Hose 1
41 Valve Connecter 4
42 Screw M12x120 2
43 Operating Handle Grip 2
44 Thin Nut M12 2
45 Lever 1
46 Reset Spring 1
47 Cylindrical Pin 8x60 1
48 Bolt M8x12 4
49 Front Support Plate for Cylinder 1
50 Bolt M8x25 2
51 Rear Support Plate for Cylinder 1
52 Flat Washer 8 3
53 Handle Grip 1
54 Square Plug 1
55 Pull Rod 1
56 Connecting Plate for Valve 1
57 Valve 1
58 Hose Nipple 2
59 Inlet Hose 1
60 Bolt 8.8 M8x50 2
61 Spring Washer 8 4
62 Oil Hose 19 1
63 Hose Clamp 28-36 2
64 Hose Connector 1
65 Right Operating Lever 1
66 Large Washer 10 2

16
No. Description Q'ty
67 Connectin Lever 1
68 Bolt 8.8 M8x401
69
Cylindrical Pin 6x40 2
70 Stroke Adjusting Lever 1
71 Round Plate 2
72 Clip 2.5 1
73 Large Washer 10 1
74 Star Knob 1
75 Adjusting Sleeve 1
76 Screw M4x60 2
77 Switch 1
78 Locknut M4 2
79 Single Phase Motor 1
80 1
Gear Pump 2.4
81 Screw M8x90 1
82 Oil Hose 16 1
83 Hose Clamp 20-26 2
84 Wheel Cap 2
85 Wheel 2
86 Flat Washer 16 4
87 Cotter Pin 2x20 2
88 Wheel Axle 1
89 Locknut M16 2
90 Bolt 8.8, M16x90 2
No. Description Q'ty
91 Screw Plug 1
92 Combined Washer 22 1
93 Main Frame 1
94 Bolt 8.8 M6x12 4
95 Flat Washer 6 4
96 Buffer Spring 1
97 O- Ring 50x2.65 1
98 Oil Filter K 1
99 Bush K 1
100 Flange 1
101 Locating Plate 1
102 Hook 1
103 Rectangular Nozzle 1
104 Locknut M14 1
105 Torsional Spring 1
106 Locating Bush for Spring 1
107 Locating Bush 1
108 Bolt 8.8 M14x60 1
109 Large Washer 14 2
110 Screw M6x10 1
111 Handle Grip 1
112 Support Wheel Assy. 1
113 Bolt M10x25 4
114 Fixing Tube 1
115 Pin B 16x85 1
116 Clip 3 3
117 Pin B 12x50 2

EC Declaration of Conformity
We, The Importer
Titan Pro Ltd
Declare that the product Titan 11 Ton Electric Vertical Log
Splitter
Model – TPLS11TV
Complies with the following directives:
EN609-1:2017 - Machinery Directive
2014/30/EU - Electromagnetic Compatibility Directive
2005/88/EC – Noise Emission in the Environment by equipment
for use outdoors Directive.
Standards and technical specifications referred to:
EN 609-1:2017
EN 55014-1:2017 EN
55014-2:2015 EN
61000-3-2:2014 EN
61000-3-11:2000
Authorised Signature
Date: 19/01/2019
Name/Title: Mr Charlie Abbott – Sales Director
Titan Pro Ltd, Unit 11 Glenmore Business Park, Wend-Al
Road, Blandford Forum, Dorset, DT11 7FP
17