Titan TTS-NP Series User manual

1
Models of the TTS-NP series
Industrial videoscope with 2 or 4 way swiveling
camera head
User manual

2
Safety recommendations
 This device must not be used for medical or veterinary purposes.
 Do not use this item in explosive atmospheres.
 Do not modify or disassemble the unit.
 Do not subject the insertion tube (camera cable) or other cables to strong pulling.
 Do not move the display unit around by holding the cables. Otherwise the insertion tube or cables may
be damaged.
 Do not subject the distal end and the angulation section to severe impact, pulling or bending. Otherwise
the precision components that make up the distal end and the angulation section may be damaged.
 Do not allow any other liquids than water, saltwater, machine or diesel oil to come into contact with the
insertion tube. Otherwise the insertion tube may be damaged.
 Do not allow water to come into contact with other parts than insertion tube. Water creates the risk of
electric shock. All parts of the device, except of the camera cable and camera head are not waterproof.
That’s why the main unit should not be submerged into liquids or being used or stored in wet
environment. Don’t use or store the device at temperatures higher than 60°C or lower than -20°C and
store it in dry and adequately ventilated environment.

3
Open the battery compartment
1. Use the supplied screwdriver to remove the screw at the bottom of the handle and pull out the
battery compartment.
2. Open the battery compartment by lifting the cover carefully.
3. Replace the 2 supplied batteries, observe correct polarity.
4. Close the cover of the battery compartment. Make sure that the two small hooks at the top inside of
the cover hook into the two small slots inside at the top of the battery compartment.
5. Reinstall the battery compartment and tighten the screw.
Charging the batteries
Insert the 2 Li-ion batteries into the supplied battery charger. Pay attention to correct polarity.
Plug the charger into a standard wall outlet.
The charging is finished when the 2 indicator lights at the top of the charger turns green. Charging
time to reach full charge needs approx. 7 hours. The fully charged battery can continuously works
up to 8 hours.
Note: Do not mix old and new batteries. Do not mix alkaline standard (carbon-zinc) and
rechargeable (nickel cadmium) batteries.
Never dispose of the device or used batteries/rechargeable batteries in
household waste. The user is obligated to take end-of-life devices to a
designated collection point for the disposal of electrical and electronic
equipment. And consumers are legally required to take used batteries
to appropriate collection sites, the retail store where the batteries were
purchased, or wherever batteries are sold.

4
Parts and their functions
01 display 08 arrow key up 15 DC in
02 playback 09 MENU button 16 reset
03 charge i
ndicator
10 OK 17 headphone
04 power indicator 11 camera cable 18 video key
05 freeze k
ey
12 m
icro USB
19 illumination/brightness
06 arrow key down 13 HDMI o
utput
20 snapshot
07 power on/off 14 TF card slot 21 exposure to light
(except of TTS-S08-6.0(D)
– there this button means
lens change - front to side
and vice versa)

5
t
Button Preview mode Playback mode Indication mode Menu mode
no function switch to next
photo or video
adjust optional
functions or options
select previous function
or option
no function go to the previous
photo or video
adjust optional
functions or options
select next function or
option
enter to menu mode enter into menu
mode
enter to menu mode no function
choose indication mode combined with
to confirm
deleting of files
choose next function confirm selection
or option
enter into playback mode return to preview
mode
enter into playback
mode
no function
freeze image delete this file freeze image return to the preview
mode/indication mode
power off power off power off power off
illumination/
brightness
no function illumination/
brightness
no function
start /stop
video recording
Press this button to start
video recording. REC
appears in the top left
corner to indicate
recording status. Press it
again to stop recording.
REC will disappear
accordingly.
select recorded
videos
start /stop
video recording
Press this button to
start video recording.
REC appears in the
top left corner to
indicate recording
status. Press it
again to stop
recording. REC
will disappear
accordingly.
no function
Snapshot – press this
button to take a picture.
After that system
automatically returns to
preview mode.
select recorded
photos
Snapshot – press this
button to take a
picture. After that
system automatically
returns to preview
mode.
no function
Button description

6
There are 4 basic modes for easier usage:
Operation
brightness (except for
model TTS-S08-6.0(D) –
there this button means
lens change - front to side
and vice versa)
no function brightness (except
for model
TTS-S08-6.0(D) –
there this button
means lens change -
front to side and vice
versa)
no function
preview mode live image, snapshot, video recording
playback mode view photos or videos on memory card or delete them
indication mode optional functions as:
illumination, brightness , exposure, zoom, freeze,
rotation, image colors, screen format, white balance
menu mode system settings
Operation modes

7
Button Function
brightness (5 levels)
exposure (0.0, + 1,0, +2,0, -2.0, -1,0)
zoom (original = 1x, 2x, 4x, 8x)
freeze image
90° image rotation (up, down, left, right)
adjusting image colours: original, negative, black & white
change between full screen and 16:9
scale for measurements – currently without function
white balance (AUTO, cloudy)
Buttons of indication mode and their functions

8
Press the MENU button in preview or indication mode to display options as follows:
For all options of the system setting applies:
Choose the respective options by moving with the arrow keys and confirm your
selection with OK. You can leave the menu mode and return to preview mode by pressing the
‘freeze’ button (except under the ‘Date & Time’ option. Under ‘Date & Time’ you can leave
by pressing OK.)
Language
You can choose between 10 languages. Use the arrow keys to move up and down and confirm your
selected language with OK.
System settings in menu mode

9
Date & Time
Confirm your selection of ‘Date & Time’ with OK. A new submenu will open. A red cursor shows
you the adjustable values like year, month, date (YY/MM/DD), hours and minutes. Increase the
value by pressing the up arrow and reduce it by pressing the down arrow .
You can move the red cursor to the next value by pressing the ‘freeze’ button
Power Save
Adjust the time limit for automatically shut off. You can choose between OFF (without
automatically shut off), 1 min., 3 min. and 5 minutes.

10
Date Stamp
The ‘Date Stamp’ function allows you to add the recorded date and time on your photos or videos.
You 3 options:
OFF: Photos and videos are shown WITHOUT date and time.
Date: Date of the recording appears on the photos and videos.
Date&Time: Date and time of the recording appears on the photos and videos.
Format
‘Format’ means to erase all data stored on memory card. But please note that all data are deleted
irrevocably. If you choose ‘Format’ a submenu will open where you can choose ‘Yes’ or ‘No’. Yes
deletes all photos and videos. If you select ‘No’ nothing will happen and you will return so the all
system settings in menu mode.

11
Reset All
When you want to delete all your settings, you can reset the system to default settings.
After confirming ‘Reset All’, a submenu with ‘Yes’ or ‘No’ will open. Yes means that all your
settings will be deleted and reset to factory settings. ‘No’ means that nothing will happen and your
settings will be retained.
FW Update
That option has normally no function. An automatically ‘FW Update’ (firmware update) by user is
not possible. Only in case of problems and when you contact us we can possibly help you with a
firmware update. For the firmware update you need a special memory card which includes that
update.

12
Caution when pulling out the camera cable
When pulling out the camera cable please hold it as straight as possible otherwise it could be
damaged.
Cleaning
Cleaning insertion tube
 Clean the insertion tube immediately after withdrawing. Because leaving it dirty could
cause corrosion.
 Wipe thoroughly with a piece of gauze or a cloth moistened with neutral detergent. As a
second step moist gauze or a cloth with clear water and use it to clean the camera cable.
Finally use a dry cloth to wipe off all moisture.

13
Cleaning distal end
Hold the rigid portion of the distal end and use a clean soft piece of gauze, cloth or a cotton swab to
wipe off dirt and liquids. The best results may obtained by using commercially available absolute
ethanol.
Cleaning main unit
Moisten a soft, clean cloth with clean water and wipe for cleaning the main unit. Finally dry it with
a clean dry cloth.
Storage
 Store the instrument at normal room temperature and air humidity.
 Straighten the angulation section when you place it into the carry case.
 Store the equipment at a clean, dry and frost-protected place.

14
Problems & solutions
P: No image on the screen after turning the power on
S: Battery is exhausted. Connect the main unit to the power adapter and recharge or replace the
battery.
P: Unable to take photo or record video
S: No TF card inserted, wrongly inserted, full or faulty.
P: How to shut down the sytem
S: When all functions freeze or fail, insert an insulated needle into the hole (“Reset”) at the side
of the main unit will be reset and restarts automatically.
Display
LCD panel 5” 16:9 TFT LCD
USB connector micro USB
video output HDMI port
recording media TF card (4 GB included)
photo 1280x720 JPEG
(400x400 JPEG for 2.8mm and 3.0mm)
video 1280x720 MOV
(400x400 MOV for 2.8mm and 3.0mm)
power source Lithium battery 2 x 3350 mAh
AC adapter: input 100-240 VAC 50/60HZ,
output 5V DC

15
Working environment
operating
temperatures
distal end and insertion tube: 0-60°C
other parts excepted of above: 0-40°C
operating humidity 15-90% RH
waterproof insertion tube IP67
other parts no waterproof construction
Certifications
CE: This device is CE conform and complies with the EC directive
EN55032:2015/AC:2016-07
EN55035:2017
FCC:
Compliance with FCC part 15B
WTX19X06040678E
RoHS
WTX19X06040679C
Imprint
This manual was published by Titan Technology GmbH, An der Feuerwache 9, D-41836
Hückelhoven (www.titan-tech.de). All rights, including translations are reserved. Any reproduction,
e.g. photo-copying, microfilming or storage on electronic media requires the prior written consent of
the publisher. Those instructions for use reflect the current technical specifications at time of print.
Changes in technology and equipment are reserved.